Search Documents

By S. Vézina

"Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/ communication technologies, better educated populations, climate change, longrange transport of toxics, and the increasing influence of non-governmental organizations (NGOs) and multistakeholders.As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental management systems (EMS) have been introduced not only to meet the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO 14 001) is a common practice.Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities, and a variety of government infrastructures to obtain a “license to operate.” This paper presents the structure of Cambior’s EMS and how it was adapted and implemented in the company’s operations in South America."

Jan 1, 2006

By W J. Riva

This paper reviews the coal mining operations of The Canmore Mines, Limited, at Canmore, Alberta, paying particular attention to the use of this coal by the metallurgical and chemical industries. The characteristics of the deposits are outlined, and the mining and processing methods used are discussed. Introduction M INING in the Cascade coal area of Alberta began form-ally in 1886 when the Canadian Anthracite Coal Company was granted its charter. Earlier operations had been confined to prospecting and family-type enterprises serving the market area within barging distance on the Bow river. From 1886 to 1964, seven mines were opened between Banff and Ribbon Creek; six of these have since been abandoned, leaving the B c 0 L. original tenant, under the name of The Canmore Mines, Limited, as the sole survivor. The town of Canmore, hub of the mining ventures, is located on the main line of the C.P.R. and on the Trans-Canada Highway, 67 rail miles west of Calgary and 57 4 miles east of Vancouver, as shown in Figure 1.

Jan 1, 1965

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

By René Lefebvre

Numerical simulations of the physicochemical processes related to acid rock drainage (ARD) in the Sugar Shack South rock pile of the Questa Mine were performed with the TOUGH AMD simulator. The objectives were to 1) identify the main processes responsible for observed present-day conditions, 2) provide an estimate of gas phase humidity transfer, and 3) give a preliminary indication of the potential impact of closure involving the installation of an alluvial soil cover. Modeling results indicated that the mine rock geometry (thin layers placed along steep mountain slopes) favors the onset of strong thermal air convection. Simulations also indicate that resloping the piles would not significantly reduce convection and oxidation. For simulation purposes, a potential cover with the permeability range of a local alluvium was investigated and found to be of questionable effectiveness since its permeability can exceed the value of 3x10-13 m2 required to prevent thermal air convection and reduce ARD.

Nov 1, 2002

By W Taylor, S Chen, R Haywood, M White, R West, J Ranasinghe

In March 2012 a combined BHP Billiton and Hatch team embarked on a program to improve the concentrate burner efficiency of BHP Billiton’s Olympic Dam copper flash smelting furnace. A multi-faceted approach including an analysis of the furnace using operational knowledge and first principles engineering led to the design and supply of a new central-lance (disperser). A new, patented, swirl method of introducing the copper concentrate into the furnace was developed to integrate with the existing concentrate burner. Plant trials in 2014 demonstrated an increase of nearly 10 percent in the oxygen efficiency of the furnace. The improved efficiency is expected to provide savings in operating costs and asset life extension of downstream gas and dust handling equipment.CITATION:White, M, Haywood, R, Taylor, W, Chen, S, Ranasinghe, J and West, R, 2015. Improved copper flash smelting at Olympic Dam, in Proceedings MetPlant 2015, pp 382–395 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By J. Yuan

Ground calcium carbonate (GCC) and chemically precipitated calcium carbonate (PCC) have become important mineral-based commodities in recent years. GCC manufacturing generally requires high purity and high brightness deposits of marble, chalk or limestone as the stone source. PCC usually uses limes made from lesser quality limestone deposits. GCC products have a wide span of particle size, with a d50 size ranging from sub micrometers to as large as several inches such as those used in landscaping. PCC products are typically limited to less than 10 µm (1,250 mesh). Each PCC product has a narrowly distributed size range. GCC and PCC products tend to have higher levels of whiteness com-pared with other traditional filler and extenders, such as kaolin and talc. Published statistics of GCC production volume often vary due to the exclusion of certain size range GCC products. According to Roskill’s latest estimate, world GCC capacity was believed to exceed 56 Mt (62 millionst) during 2004 for all grades.

Jan 1, 2005

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Miller, M Dowling, R Domotor

"This paper is focused on blasting activities undertaken as part of the Pacific Highway Upgrade – Tintenbar to Ewingsdale – project (T2E). This is a ‘priority 1’ Pacific Highway road construction project in New South Wales (NSW), to be completed by mid-2015 (weather permitting). T2E will provide approximately 17 km of dual carriageway road starting at the northern end of the Ballina bypass and extending to the Ewingsdale interchange, and will complete the existing dual carriageway road between Ballina and the NSW/Queensland border.Roads and Maritime Services (RMS) (formerly the Roads and Traffic Authority) is delivering the project on behalf of the NSW state and federal governments. In October 2011, RMS awarded a contract to Baulderstone Pty Ltd (now Lend Lease Engineering Pty Ltd – Lend Lease) to design and construct T2E. One of the key elements in this project is the St Helena Tunnel.In order to avoid the steep grades of St Helena Hill, eliminate a well-known accident black spot and maintain the aesthetics of the Byron hinterland escarpment, RMS and Lend Lease prepared designs to construct a 434 m long dual carriageway tunnel, 46 m below the ridge line of St Helena Hill. Lend Lease elected, where geotechnical conditions permitted, to use drill and blast methods to excavate the full tunnel profile, instead of traditional mechanical excavation techniques.Since all blasting locations (both inside and outside the tunnel) were in close proximity to nearby residents, the NSW Department of Planning and Infrastructure imposed strict air blast overpressure (airblast), ground vibration (vibration) limits and limited working hours. Both RMS and Lend Lease recognised that these restrictions meant that nearby residents may be exposed to blasting activities for longer than was necessary. As a result, after close consultation and agreement with the nearby residents, RMS applied successfully to the NSW Department of Planning to increase the airblast and vibration limits, as well as the working hours.Working under these new conditions, Lend Lease employed a range of best practice drill and blast technologies provided by both Orica Australia Pty Ltd and Atlas Copco Mining and Rock Excavation to improve the safety and efficiency of blasting activities and to minimise the potential negative impacts of the blasting works on affected residents. These technologies included: the use of a continuous environmental monitoring system to record the results of the blast events and provide quick and easy reporting to key stakeholders to address RMS specification requirements electronic detonators to enable accurate hole detonation timing for vibration compliance and to give project engineers the flexibility and precision to alter each design to suit the geological profile of each face the use of two software programs and advanced drill rigs to enable the efficient design of blasts, electronic transfer of designs to the drill rigs, as well as in-hole monitoring and recording of drilling performance the use of a specialised bulk emulsion system to deliver fully coupled bulk explosives into face blastholes to maximise fragmentation, and decoupled bulk explosives into perimeter blastholes, to reduce overbreak and deliver a cleaner profile.By taking a progressive approach towards the environmental restrictions and the work hours imposed, as well as utilising best practice blasting techniques, RMS and Lend Lease were able to blast with confidence and achieve their production deadlines and reduce the total cost of the project.Most importantly, RMS and Lend Lease were able to meet their environmental obligations and work constructively with the nearby residents to ensure that the blasting was undertaken as safely and efficiently as possible without delay or negative impact.CITATION:Dowling, M, Domotor, R and Miller, D, 2014. Improving excavation efficiency at the St Helena Tunnel using best practice drill and blast techniques, in Proceedings 15"

Sep 17, 2014

By W. A. Dunkley, W. W. Odell

About two-thirds of the manufactured gas supplied to the public by the gas plants in the Illinois district is cnrbureted water gas. The leading generator fuel is coke, ma.de in by-product c.oke ovens or in retorts, chiefly from eastern gas coals. During the fall and winter of 1917-18, when the demand for coke by war industries and the restrictions of the Fuel Administration in connection with the transportation of coke from eastern States made it almost impossible for many gas companies to obtain their coke requireml'nts, several water-gas plants had to use bituminous coal as generator fud. Many operating difficulties were encountered, some of which were solved more or less satisfactorily in different plants. A number of plants attacked the problem rather blindly because facilities for making tests were lacking and because technical men were too busy with labor and supply problems to study thoroughly the conditions involved or to ascertain what other plants had done with this fuel. It was therefore with the hope of assisting the gas industry during this critical period, and of promoting the use of Central District coals for gas making, that the Illinois Mining Investigations, a joint agency of the U. S. Bureau of Mines, the University of Illinois, and the Illinois Geological Survey Division undertook the, tests discussed in this paper. • This report was compiled under the auspices of a technical committee appointed by Gov. Frank 0. Lowden to promote the use of Central District coals in gas manufacture as a war measure. This committee included the following representatives of the various agencies concerned: U. S. Bureau of Mines, E. A. Holbrook and W. W. Odell; Illinois Gas Association, C. W. Bradley and R. B. Harper; University of Illinois, Dean C. R. Richards, Prof. S. W. Parr, and Prof. H. H. Stoek; State Geological Survey Division, F. W. De Wolf, G. H. Cady, a.nd W. A. Dunkley. F. W. De Wolf was chairxnan of the committee and E. A. Holbrook was secretary.

Jan 1, 1924

By Matej Petružálek, Václav Vavrycuk, Tomáš Svitek, Tomáš Lokajícek

The most common type of waves used for probing anisotropy of rocks in laboratory is the direct P wave. Information potential of the measured P-wave velocity, however, is limited. In rocks displaying weak triclinic anisotropy, the P-wave velocity depends just on 15 linear combinations of 21 elastic parameters, called the weak-anisotropy parameters. In strong triclinic anisotropy, the P-wave velocity depends on the whole set of 21 elastic parameters, but inversion for 6 of them is ill-conditioned and these parameters are retrieved with a low accuracy. Therefore, in order to retrieve the complete elastic tensor accurately, velocities of S waves must also be measured and inverted. For this purpose, we developed a lab facility which allows the P- and S-wave ultrasonic sounding of spherical rock samples in 132 directions distributes regularly over the sphere. The velocities are measured using a pair of P-wave sensors with the transmitter and receiver polarized along the radial direction and using two pairs of S-wave sensors with the transmitter and receiver polarized tangentially to the spherical sample in mutually perpendicular directions. We present an inversion method for elastic parameters describing general triclinic anisotropy. We demonstrate on synthetic tests that the inversion becomes more robust and stable if the S-wave velocities are included. This applies even to the case when the velocity of the S waves is measured in a limited number of directions and with a significantly lower accuracy than that of the P wave. Finally, we analyze velocities measured on a rock sample from the Outokumpu deep drill hole, Finland, including the error analysis for several levels of confining pressure.

Jan 1, 2015

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By P. Kovalchik

The Bureau of Labor Statistics (BLS) classifies hearing loss as a separate illness category. Hearing loss accounted for 11% of all illnesses in 2005 (U.S. Department of Labor Bureau of Labor Statistics, 2006a). According to occupational data for coal mining provided by the Mine Safety and Health Administration (MSHA) from 2000 to 2005, operators that exceeded 100% noise dosage were from only seven types of machines: auger miners, bulldozers, continuous mining machines, front end loaders, roof bolters, shuttle cars (electric) and trucks (Title 30 CFR Part 62, 2000-2005). Roof bolting machine operators rank second among all underground machine operators that exceed 100% noise dose. There are approximately 600 underground coal mines with 3,930 roof bolting machine operators (U.S. Department of Labor, Mine Safety and Health Administration, 2005; U.S. Department of Labor Bureau of Labor Statistics,

Jan 1, 2008

By M. Potesser

One of the main targets in the automotive mass industry and supplying industry is the weight reduction of the vehicle for decrease of the fuel consumption. For that reason combinations of different kinds of materials and connections of, for example, steel and aluminium are developed or are already successfully field-tested. A determining factor concerning the quality assessment of the welded joint during hybrid welding is the characterization of the intermetallic Fe-Al layer regarding strength, hardness, morphology and mainly the different phases in which Fe occurs together with the Aluminum (FeAl, Fe2Al5, FeAl3.). A combination of conventional light microscopy, SEM - EDX - analysis, the usage of an atomic force microscope including a Nanoindenter and theoretical thermodynamic calculations turned out to be highly effective. Based on the attained results, the constitution of the intermetallic FeAl layer, influenced by silicon, manganese and zinc, can be predicted.

Jan 1, 2006

By Glan Dale Coe, Will H. Coghill

"INTRODUCTION Characteristics of the mineral products that are to be contrasted herein are net energy consumed in grinding to a definite top limiting size and size distribution of the ground products. Through contrasts of these grinding characteristics this paper to differences in related mineral products and in unlike products. For,example, in anticipation of the data to follow, although Joplin chert and Babeitt taconits are running mates in defying the best crushing machinery, taconite is one of the more docile and Joplin chert one of the most refractory mineral products ordinarily fed to a grinding Routine grinding tests on a great variety of ores and tabulation of the findings have been covered amply by Lennox 4/ and by Maxon 5/ and associates. In contrast to that work, the present paper is a record of random tests made over a long period, and each answered an urgent question at the moment. The work was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama. The pressure of war work prevented an organized investigation."

Apr 1, 1943