Search Documents

By Keith A. Heasley, Timotlly M. Barton

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence- Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents a case study where a mechanics-based, boundary-element program is used to calculate the surface subsidence associated with several panels of a Northern Appalachian longwall coal mine. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin seam or vein type deposits. In this paper. the program is used to calculate both the underground convergence and the resulting surface subsidence at three longwalls. The subsidence results from the model are compared with field measurements and analyzed The results from the case study in this paper demonstrate that the laminated model with calibrated properties can easily provide fairly accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies are recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

Numerical models play a significant role in the design of safe underground mining excavations and support systems. Advances in the capabilities of numerical modeling software, together with ever increasing computational speeds, have made it possible to investigate the very nature of the large-scale rock mass and its response to mining excavations. The improved understanding of the rock response obtained from modeling enhances our designs, resulting in greater stability and safety of the mining excavations. To help advance the state of the art in this field, the National Institute for Occupational Safety and Health organized the International Workshop on Numerical Modeling for Underground Mine Excavation Design. The workshop was held in Asheville, NC, on June 28, 2009, in association with the 43rd U.S. Rock Mechanics Symposium. The proceedings include 10 papers from leading rock mechanics and numerical modeling experts in the United States, Canada, Australia, and Germany. The papers address a wide range of issues, including various numerical modeling approaches, rock mass modeling, and applications in coal and metal mines.

Jun 1, 2009

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013

By A Litwinowicz, M Laxman, A Fourie, A L. Li

This paper presents a design approach and analytical methods that were used for assessing the potential of static liquefaction and developing the mitigation measures for a tailings dams. The rigour of the design and analysis approach represented leading practise in the industry to address static liquefaction, which contributed to a robust design with high confidence and certainty. The salient features of our approach to static liquefaction included geotechnical investigation and tailings characterisation, static liquefaction screening assessment, static liquefaction triggering analysis, limit equilibrium analyses and numerical modelling of static liquefaction using the NorSand model, which was amongst the first tailings dam projects involving numerical modelling of static liquefaction using these methods.

Jul 1, 2021

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

The Pilbara region, located in the north-west of Western Australia, is significant as the second-largest source of iron ore on the planet. Iron ore mines owned and operated by Pilbara Iron are located within the Hamersley Basin. This paper refers to the Greater Paraburdoo mines, the 4WEST and 4EAST pits, located on the southern margin of the Hamersley Basin. The groundwater model refers to ephemeral watercourses: Seven Mile and Pirraburdoo creeks, which are adjacent to the two pits, and Ratty Springs, located upstream from 4WEST and within Pirraburdoo creek. The spring and creeks hold cultural heritage significance for local Aboriginal communities. Two of these, the Gobawarrah Minduarra Yinhawanga (GMY) and Innawonga native title claim groups, initiated hydrological work on the two creeks and Ratty Springs, with the aim of determining the affects of dewatering on the natural water flows of these systems. The numerical model used to simulate drawdown in the Pirraburdoo and Seven Mile Creeks was derived from PMWIN Pro software and covered an area of 77 km2. The modelling period was from January 1998 to December 2004, and the prediction period was from January 2005 to December 2015. The model has four layers and incorporated effects caused by mining voids, 4WEST and 4EAST pits, creek bed material, weathered bedrock below creeks and surrounding banded iron formations (BIF). The model has been calibrated using the trial-and-error method set down by Middelmis et al (2001). The current dewatering schedule (12 ML/day) in the 4WEST and 4EAST mining areas does not affect the water table levels in the adjacent creeks significantly or for any considerable periods of time. However, changes to mine plans may occur, for example, in response to changed commodity price and may lead to significant increase in rates of vertical advancement. This, in turn, affects dewatering schedules, as greater vertical advancement requires increased dewatering effort. When an accelerated mine plan is applied to the model and dewatering rates increased to 18 ML/day, drawdowns in the creeks are more noticeable. The model has therefore helped to indicate the extent to which increased dewatering rates may be acceptable, especially in terms of immediate and longer-term damage to riparian species, ie Melaleuca and Eucalypt. Predictions from the model may also allow mine planners to schedule decreased rates of vertical advancement, where these are required to meet environmental constraints.

Jan 1, 2006

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920' s and 1930's, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a 'collector' in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Peter M. Watt

The objective s of this paper are: (a ) to examine and discuss the burdens we place on our extractive industry; (b) to compare the levels of taxation in Canada with those in other countries; and ( c) to suggest certain broad parameters within which our taxation policies may be made more rational and stable. Among the burdens identified are taxation, the ownership and use of our resources, environmental issues and the rather emotional issue of so-called 'super profits'. Finally, the paper will address certain broad but key areas of policy which need attention and agreement if our tax system is to be made more rational. Such areas include: whether and if so why the extractive industry should be given incentives;. what circumstances, if any, justify a 'higher' than normal' level of taxation, and, ?if the concept of economic rents is a justifiable one, how might a basis for them be established which recognizes the fluctuating value of much of the industry's output. Note: The paper was written before the 1977 Federal and Provincial budgets were presented. Consequently, the paper does not reflect any changes proposed in these budgets.

Jan 1, 1977

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Edwin A. Clarke

[For almost 2 decades the Bureau of Mines has been Interested in converting solid fuels to liquid fuels. Small-scale laboratory investigations were carried on for a number of years.4/ This work wad expanded substantially under authority of Public Law 290, approved by the 78th Congress on May 5, 1945. As part of the. broadened program, coal-hydrogenation demonstration plant was designed and erected at Louisiana, Mo., where: hydrogen-manufacturing and compression equipment, shoes, electric power, and other utilities and facilities were available from a discontinued wartime ammonia works . The plant uses the direct -hydrogenation or Bergius process, but the process differs from prewar European practices in many respects. Many noteworthy improvements h eve bean made, particularly by substituting automatic instruments for manual control of process variable's, in line with modern American processing practices. The over-all objective of the demonstration plant is to bridge the gap between laboratory end commercial-scale operation by furnishing cost and engineering data to develop a synthetic liquid-fuels industry when it proves technically and economically justified. Fitting into the over-all program, specific objectives o early runs were to (1) train personnel who had no experience with this type of operation, (2) break in the installed equipment, (3) obtain successfully integrated operation of the entire plant, and (4) work towards obtaining data on the hydrogenation of coal-tar oil and a typical low-ash coal. In beginning fan integrated operation, it is common practice to operate and obtain reaonably smooth performance of each unit before the over-all operation is undertaken. The first part of the plant completed was the refinery, consisting of several fractionating systems, a stabilizer, and a chemical treater.]

Jan 1, 1953

By W. Greuer

The objective of this paper is to demonstrate how site-specific slope stability analysis can be performed entirely from the desktop with satellite images, Geographic Information Systems (GIS), and slope stability software packages. This type of analysis would effectively eliminate or restrict the need for expensive field testing of geotechnical properties of a hillside, pit wall, berm, or embankment, and would be particularly useful for slope failure mitigation at remote or otherwise inaccessible locations.

Jul 17, 2000

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

By Alexandre da Silva Rocha, Luiz Maurício Barreto de Azevedo, Leonardo Sales Araújo, Rafael Menezes Nunes, Matheus Campolina Mendes, Thiago Marque Ivaniski, Luiz Henrique de Almeida

Superliga 718 é uma liga de níquel endurecida majoritariamente por precipitação controlada. As suas principais aplicações são nas indústrias aeroespacial, óleo e gás e nuclear devido a capacidade da manutenção das suas propriedades desde a temperaturas criogênicas até aproximadamente 650°C. Para atenuar fenômenos deletérios de natureza intergranular, neste material são feitos tratamentos termomecânicos específicos para se se aumentar a fração dos contornos do tipo Σ3n.Portanto, o objetivo deste trabalho é analisar duas rotas termomecânicas capazes de aumentar a fração destes contornos por ciclos iterativos de deformação por trefilação, seguido de solubilização em temperaturas sub-solvus  e super-solvus  e envelhecimento além de avaliar a influência da trefilação na precipitação de  mesotextura e tamanho de grão  Para a análise microestrutural, foram feitas imagens de microscopia eletrônica de varredura(MEV) e difração de elétrons retroespalhados (EBSD). Foi feita simulação computacional por elementos finitos do processamento termomecânico para avaliar a distribuição e o grau da deformação no processo. Os resultados mostram que é possível atingir uma elevada fração de contornos do tipo Σ3n pelo processo de trefilação, contudo, a heterogeneidade da deformação ao longo da seção radial influencia em parâmetros microestuturais .

Oct 10, 2019