Search Documents

By Breno Totti Maia, Rubia Teodoro Silva, Daniel A. G. de Carvalho, Aline Lima da Silva, Gilvan Nascimento de Souza

Para a maior eficiência na técnica conhecida como Slag Splashing, empregada com fins de manutenção e reparo de refratários de convertedor LD, a escória deve apresentar características apropriadas em termos de viscosidade e fração de sólidos. No presente trabalho, desenvolveu-se uma metodologia híbrida, combinando a utilização de padrões para a caracterização visual de escórias na planta, baseada em critérios de atribuição de notas, com a simulação termodinâmica usando o software FactSage para determinação das fases presentes na escória, quantificação de fração de sólidos e cálculo da viscosidade efetiva. A metodologia proposta permite identificar os quadrantes ideais de viscosidade efetiva, fração de sólidos e teor de ferro total, de modo que se possa garantir escórias com notas altas, apresentando qualidade apropriada para o processo. Os resultados indicam que as escórias com nota 3 (ótima) são obtidas nas seguintes condições: temperatura de fim de sopro de 1690-1720ºC, viscosidade efetiva na faixa de 0,070-0,650 Pa.s, fração de sólidos de 13-22%, teor de ferro total na escória de 14-17,5%..

Oct 1, 2019

By Andrey de Moraes Barcelos Casanova, Rebeca Vieira de Oliveira, Juliana Diniz e Castro, Danilo Abílio Corrêa Gonçalves, Patricia Freitas Rodrigues, Thiago Henrique Fernandes Dias Ferrão, Naiara Vieira Le Sénéchal, Rodolfo da Silva Teixeira, Andersan dos Santos Paula

Este trabalho avaliou a efetividade do tratamento térmico de solubilização de uma liga de NiTi com 58,5%at. Ni comparado a uma liga de composição equiatômica, elaboradas por vacuum arc remelting (VAR). A solubilização foi realizada à 950 °C, em forno de atmosfera não controlada, com tempo de encharque de 2 h, seguido de resfriamento rápido em água à temperatura ambiente. Foram analisadas imagens de microscopia óptica e de microscopia eletrônica de varredura, após preparação metalográfica, das amostras fundidas e solubilizadas, bem como, quantificação da segunda fase pela análise de micrografias ópticas. As propriedades mecânicas foram avaliadas pelo ensaio de dureza por microindentação Vickers. O tratamento térmico imposto resultou em alterações morfológicas na liga equiatômica e não foi possível verificar a dissolução completa dos precipitados da liga com elevado teor de Ni. Foi observado a diminuição da dureza com a solubilização do NiTi equiatômico, e aumento na liga Ni58,5%at.-Ti41,5%at.. Logo, para se obter uma solubilização ótima das ligas, se faz necessário um tempo de encharque maior.

Oct 22, 2019

By Antônio Carlos Aguiar Gagno Junior

O Sistema de Controle de Equipamentos de Radiofrequência (SCER) nasceu a partir de uma demanda da área de Telecomunicações com o objetivo de minimizar as interferências dos diversos equipamentos emissores e receptores de ondas de rádio existentes em todo o perímetro da Usina ArcelorMittal Tubarão. Anterior ao sistema, todo o cadastro, controle e alocação destes equipamentos era feito em planilha Excel, mantida pela área de telecomunicações. Todas as verificações para liberação da instalação/configuração do equipamento a ser instalado eram feitas manualmente, com auxílio de equipamento analisador de espectro de frequência. Com a implantação do SCER, as fragilidades do controle manual foram supridas, trazendo o diferencial de cálculos automáticos de interferências feitos pelo sistema em função dos parâmetros de ajuste de cada equipamento, da sua abrangência e localização geográfica. Através de uma interface Web, os usuários podem não só controlar os equipamentos, fabricantes, modelos e aplicações, como também visualizar em mapas, com georreferenciamento, as áreas da Usina em que estes equipamentos atuam, bem como alterar os polígonos e perímetros de alcance e abrangência das áreas.

Aug 16, 2017

By Beatriz Lemos Clemente

A maneira com que acontece a nucleação interfere diretamente na forma dos contornos de grão e também nas propriedades do material em questão. Para visualizar melhor, pode-se utilizar uma célula cúbica, na qual é possível notar que em cada eixo há diferença de textura e densidade entre os grãos já desenvolvidos. Neste trabalho, foram empregadas duas vias de estudo a fim de obter os resultados desejados. A primeira delas é a nucleação homogênea dos grãos e a outra, a nucleação não homogênea, ambas com velocidade constante. Esse fenômeno pode ser visto durante a recristalização de grãos. Rios e Villa [6] criaram um método efetivo para analisar a cinética das transformações homogêneas e não homogêneas a partir do método de JMAK[1-5]. Para comparar método analítico foi desenvolvida uma simulação computacional com base no modelo analítico Rios e Villa [6], foi utilizado a metodologia do Cone Causal (método estocástico). Os gráficos gerados confirmam a teoria de Rios e Villa [6] para esses casos particulares e comparam os resultados obtidos com o conceito de JMAK [1-5].

Oct 30, 2017

By Ivan R. Jankov

No setor industrial no mundo todo, são exigidas as emissões cada vez mais restritivas. Nas plantas onde o Precipitador Eletrostático já está instalado, a solução com o melhor custo-benefício para reduzir as emissões de material particulado abaixo de 20 mg/Nm3 é com o Filtro Híbrido. Esta tecnologia consiste em combinação dos princípios de operação de um Precipitador Eletrostático (utilizado na entrada do sistema), com uso de campo elétrico para separação de material particulado do fluxo gasoso, e de um Filtro de Mangas (utilizado na saída do sistema), com uso de tecido para retenção de material particulado. Salienta-se que a viabilidade de implementação do Filtro Híbrido depende da configuração original do Precipitador Eletrostático (i.e. altura das placas, número de campos, largura da carcaça) que determina o espaço disponível para mangas, bem como as velocidades máximas do gás dentro da carcaça. Na indústria siderúrgica, este tipo de retrofit já é utilizado em planta de sinterização, mas também é aplicável para despoeiramento de fornos de cal e de plantas de pelotização.

Oct 30, 2017

By Flavio Viana Diniz Soares

Neste trabalho foi avaliada a desnitrogenação ao longo do tratamento no Desgaseificador a vácuo – RH2 da Usiminas, a partir da amostragem de 10 corridas de aço estrutural para chapa grossa de classe de resistência mecânica de 50 kgf/mm2 microligado com nióbio e titânio, de composição química e em condições de processo similares. Foram retiradas amostras de aço nos tempos 0, 5, 10, 15 e 20 minutos de cada corrida. Os dados foram tratados em dois grupos baseado no teor inicial de nitrogênio. Para o grupo de corridas com o teor menor que 39 ppm, não se verificou redução nos valores de nitrogênio após o tratamento no RH. No grupo de corridas com teor de nitrogênio acima de 39 ppm, evidenciou-se uma redução média de 17% do teor de nitrogênio. Além disso, o teor médio final de nitrogênio em ambos os grupos ficaram com diferença de apenas 2 ppm, evidenciando que o desgaseificador a vácuo RH foi eficiente na redução de nitrogênio para teores acima de 39 ppm.

Oct 30, 2017

By Camila Fernandes Rezende, Camila Simon Christ, Vinicios Andreatta, Marcus Vinícius Pimentel Gomes

A integração e cruzamento de dados de diversos sistemas para as unidades técnicas de processo sempre foi uma necessidade e um desafio. Para a unidade técnica da Aciaria, a integração de dados gerados pela Instrumentação, Automação e MES (Manufacturing Execution System) é imprescindível para a análise e otimização do processo. Este processo feito de forma manual era trabalhoso, improdutivo e com grande potencial de erros. Mesmo com o suporte da área de TI (tecnologia da informação) e TA (tecnologia de automação), em alguns casos este processo era inviável devido à complexidade. Com a utilização de uma ferramenta analítica, já utilizada em outros processos produtivos da empresa (Laminação de Tiras a Quente e Qualidade), foi possível prover acesso a diferentes bases de dados, permitindo a integração dessas informações de forma simplificada, ágil e única, todos consumindo os mesmos dados, com as mesmas regras. A automatização deste processo trouxe benefícios como: melhora na qualidade do dado, democratização das informações e tempo para investigação de problemas e otimização de processo, além de menor dependência das equipes de TI e TA.

Oct 1, 2019

By H. C. L. Reemeyer

"The mining industry faces increasing economic, environmental and social challenges, as easier deposits deplete and ores become more difficult to mine and process; head grades decline; projects migrate to increasingly remote and difficult geographies; and the industry faces more stringent environmental and social standards. While these factors increase costs and risks, they also present opportunities for a more integrated approach to mining, processing, materials handling and waste management. Two key areas of risk are in tailings and water management. As mining and processing tonnage rates continue to increase, the disturbance footprints, water and energy consumption and scale of tailings storage facilities also rise. These factors can be mitigated by more selective mining, ore sorting and pre-concentration, and more intensive tailings dewatering. Such alternatives must be considered in conjunction with the selection of mining method, metallurgical flowsheets, major equipment selection, and key process design criteria. For example, increasing the grind size of a concentrator reduces energy consumption and eases tailings dewatering, but may cause challenges with metal recovery. Emerging technologies will be reviewed, and economic and environmental trade-offs for eco-efficient alternatives will be presented for metal sulfide mines.INTRODUCTION The metals mining industry faces significant challenges that can affect its financial viability and social license to operate. There has been a consistent decline in ore grades and a relentless push towards larger operations to capture perceived economies of scale. With these larger operations, the environmental footprint of mines has increased. Water and energy consumption, and resulting GHG emissions have also risen. In recent years, two issues have raised special concerns for stakeholders and companies: • Water scarcity, particularly in drier regions of the world such as Northern Chile, SW USA, Southern Africa and Australia • Tailings risks, following the high-profile failures of the Fundao tailings dam in Minas Gerais, Brazil in 2015 and the Mount Polley tailings dam in BC, Canada in 2014"

Jan 1, 2017

By J. J. Shields

The Bureau of Mines observed two different types of longwall mining; the advancing longwall method and the retreating longwall method at seven bituminous coal mines located in five of the coal producing states. In two mines using the advancing face method, the coal faces were abandoned because of roof failures and poor production. In the other five mines using the retreating method, roof control was good as was production. The success of longwall mining depends on good roof control and good production. The use of self-advancing hydraulic roof supports, such as Westfalia, Dowty, and Wanheim props along with Westfalia coal planers and the Anderton and Eickhoff shearer-loaders have been a factor in recent successes.

Jan 1, 1967

By D. M. Dabbs

A static dew point technique has been used to evaluate the solubility of arsenic in ?slag and its dependency on P02 at temperatures of 1458 and 1523K. The ferrous-ferric ion ratio of the slags ranged from 3.9 to 23.8. These values correspond to partial pressures of 02 ranging from 10-8 to 10-12 atm. The solubility of arsenic in slag was found to be independent of? P02? The data indicate that elemental arsenic exists in silicate ?slags. This result was further substantiated by mass .spectrometric analysis of doped slag specimens.

Jan 1, 1983

By Jhon F. Chávez

"El presente texto describe las técnicas de análisis, diseño y optimización de las mallas de sostenimiento activo, de forma que optimiza las condiciones de seguridad y reducción de costos de sostenimiento en las labores de la minera Iscaycruz, así como los sobrecostos por daños a instalaciones y equipos por accidentes relacionados a falla en el sostenimiento activo."

Jan 1, 2016

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By Robert G. Bottge

The Bureau of Mines has engaged m a program to determine the availability of land for mineral exploration and development in Alaska. Land availability, based on ownership and Federal and State laws and policies, is compared with mineral terranes and mineral deposits. This is the fifth of six regional studies, which cover the State with a comprehensive set of maps and data compilations. This study covers an area of 112.3 million acres in western Alaska. In July 1986, 41.0 million acres, 37% of the study area, were available for mineral exploration and development; 14.6 million acres, 13%, were available with restrictions; and 56.7 million acres, 50%, were unavailable. Nearly 65% of the unavailable land is classified as national parks, preserves, wildlife refuges, and wild and scenic rivers. Of the 34.0 million acres of mineral terranes that underlie the study area, 12.9 million acres, 38%, are available for exploration and development; 3.6 million acres, 11%, are available with restrictions; and 17.5 million acres, 51%, are unavailable.

Jan 1, 1988

By Edir Neves Teixeira

O presente trabalho teve como objetivo o estudo para otimização de distintas condições de tratamentos térmicos de solubilização e envelhecimento em liga forjada de NiTi rica em Ni visando características e propriedades adequadas para aplicações superelásticas. As características microestruturais e composicionais foram avaliadas por Difração de Raio-X (DRX), por Microscopia Eletrônica de Varredura (MEV) associada à Difração de Elétrons Retroespalhados (EBSD) e ao Espectrômetro de Energia Dispersiva de Raio-X (EDX), e correlacionadas com as medidas de dureza Vickers. Baseados em resultados da literatura, apresentou características mais promissoras para tratamentos de solubilização a 950ºC por 120 minutos conjugado com envelhecimento a 350ºC por 30 minutos, ambos com resfriamento em água.

Aug 8, 2018

By Jr. Frank Parrish

This report describes the performance of 17 selected water-injection projects producing from Pennsylvanian-and Permian-age reservoirs. Illustrations depict reservoir structure and thickness, and production and injection history. A selected bibliography of publications pertaining to area oil recovery and geology is included. Tabulations of field and reservoir data reveal marked differences in the projects. Increased oil recovery resulted from injecting water in most cases; however, seven projects recovered less oil than the operators anticipated. Oil recovery by water injection ranged from 0.2 to 262 bbl per acre ft, or 0.1 to 22.5 pct of the initial stock-tank oil in place. Major reasons suggested for poor performance include: (1) Adverse directional horizontal permeability, (2) channeling of injected water through fractures or zones of high permeability, and (3) lack of containment of injected water. One 330-foot-deep project is among the first successful shallow water-floods in north Texas. Another project is the first successful Canyon sand-stone waterflood reported in the area. Previous gas injection in two Cisco sandstone projects did not prevent the reservoirs from responding favorably to waterflooding.

Jan 1, 1965

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

By A. V. Kuznetsov, R. I. Kamkin, V. M. Paretskiy, A. Y. Mamaev, V. P. Bystrov, A. S. Vernigora

"Vanukov furnace technology is an efficient, proven pyrometallurgical injection technology, used extensively in Russia and Kazakhstan for a number of different applications. The technology was most widely adopted for processing copper sulfide concentrates for matte in smelters in Norilsk, Revda (Russia) and Balkhash (Kazakhstan). The following applications also were developed and tested at industrial scale: treatment of sulfide lead and lead-zinc concentrates, laterite nickel ore, production of cast iron, treatment of antimony gold-containing ores, and municipal solid waste. In this paper, current experience of Vanukov furnace application to these technologies is described with a number of general development trends and new areas of application.IntroductionAt the present time, the Vanukov process, developed at the Moscow State Institute of Steel and Alloys at the Department of metallurgy of non-ferrous, rare and noble metals with collaboration with other research organizations, is a highly efficient technological solution for processing different kinds of raw materials. The process was invented by Professor Andrey Vladimirovich Vanukov, whose research work began in 1949. From 1956 to 1975 test runs of the technology were carried out at the smelters in Norilsk and Balkhash. In 1976 a pilot Vanukov furnace was built in Ryazan. Furnace designs was modified to suit the various test programs. A major objective of each experiment was the determination of optimal working conditions for processing different types of raw materials such as copper, copper-nickel, copper-zinc, lead or pyrite concentrates, and materials containing secondary lead and zinc. After the death of Andrey Vladimirovich Vanukov in 1986, this technology and furnaces based on the technology were named after him: “Vanukov process” and “Vanukov furnace”. Today, the following furnaces based on Vanukov technology are either working or were tested at semi-industrial scale: three in Norilsk, two in Revda (Russia) and two in Balkhash (Kazakhstan) for treatment of copper sulfide concentrates for matte, one in Orsk (Russia) for processing laterite nickel ore, one in the Buruktal plant (Russia) for antimony gold-containing ores for antimony oxide sublimates and gold-containing metallic antimony, and one in China for processing sulfide lead and lead-zinc concentrates for production of black lead and zinc-containing sublimates."

Jan 1, 2011

By Spencer R. Titley

Nearly three decades of intense research, corresponding with a period of unparalleled discovery and the advent of scientific advances and hypotheses of ore formation, has resulted in a great body process-focused research concerning how ore deposits form. The development of process models and their application has proceeded more or less in step. Discoveries have been made in mineralized regions such as provinces and districts but generally without a comparably developed understanding of why provinces and ore bodies exist and, except in general terms, where ore deposits are within districts and regions. The process of discovery is still referred to as search and exploration budgets are heavily weighted toward exploration drilling.

Jan 1, 1995

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014