Search Documents

By J. E. McDonald, J. G. Eberhart

A model is discussed from which the work of adhcslon .tor liquid transition metals on aluminum oxide surfaces can he calculated, A close-packed (00011 oxygen surface on A12O3 is assumed with two different types of surface sites: one type involving metal-oxygen bonds and the other man der Waals into actions. The work of adhesion is thus expressed as the sum of these two bonsding free energies. Calculated works of adhesion for nickel, titanium, chromium, and zirconium on sapphire agree well with the experimentally determined quantities. The model is extentled to the calculation of the work of adhesion and shear stress required to remove a thin metal film from a sapphire substrate and is in good agreement with experimental values. The obsewed dependence of the work of adhesion on the free energy of oxide formation of the metal is shown to also provide an interpretation of the tittle dependence of thin-film adhesion. THIS paper presents a model for the type of bonding which occurs across a metal-A12O3 interface. The model is used to explain the results of two types of experiments in which such an interface exists: 1) the adhesion of thin metal films on Al2O3 substrates and 2) the wetting of A12O3 by liquid metal drops. The adhesion of thin films to various substrates has been the subject of a variety of investigations.'-' Benjamin and weaver3 and Bowie,6 using the scratch test developed by Heavens,10 studied the adhesion of metallic films to glass substrates. Their observations for noble-metal film adhesion agree well with an adhesion model involving a van der Waals type of bonding between the film and the substrate. For films of metals whose free energy of oxide formation. ?F°f, has a negative value. Benjamin and weaver3 and Bowie6 found a time-dependent adhesion with an initial value that can be interpreted in terms of van der Waals interactions but a larger terminal value which was related to ?F°f, Karnow-sky and Estill7 deposited films on sapphire at elevated temperatures and noticed no time dependence of film adhesion but a similar correlation with ?F°f. Because of the kinetic problems associated with thin-film adhesion it is desirable to examine adhesion in an equilibrium system. The wetting behavior of liquid-metal drops on Al2O3 provides such a system. Systems of this metal-ceramic type have been studied extensively.11 Humenik and Kingeryl2 have measured the wetting of A12O3 (and other substrates) by several metals and have pointed out that the wetting ability of these metals increases with increasing values of -?F°f. It is thus seen that thin-film adhesion and metal wetting on A12O3 are both related to the tendency of the metal to react with the surface oxide ions of the Al2O3 substrate and, because of this, both phenomena should be explainable by an appropriate model for the metal-Al2O3 interfacial bonding. In the sections that follow, wetting and adhesion data on A2O3 are reviewed and a model is presented by which these phenomena can be interpreted. ANALYSIS OF WETTING EXPERIMENTS In an equilibrium system involving a liquid-metal drop on a solid Al2O3 substrate, the work of adhesion, WAD, is defined by the Dupre, equation as WAD = ?s + ?L -?sL [1] where ?s and ?L are the surface free energies of the solid substrate and the liquid drop, respectively, and ?sL is the interfacial free energy. The work of adhesion is the work required to separate a unit area of the solid-liquid interface into two surfaces. The work of adhesion is usually determined from a sessile-drop experiment in which yL and the contact angle, ?, are measured. The Young-Dupr6 equation is then used to calculate WAD Wad = ?L (1+ cos ?) [2] The literature of this subject has been examined and Table I shows work of adhesion data for various liquid metals as measured on A12O3 substrates. The standard free energy of oxide formation of the metal at the temperature of the wetting experiment, ?F°f . is also tabulated in kcal per g-atom of oxygen. The data is grouped according to the gaseous atmos-

Jan 1, 1965

By P D. Munro

On the occasion of the 14th Mill Operators’ Conference and marking 40 years since the first one was held in Mount Isa in 1978, it is fitting to review the history of the Conference and its development over that time.The first 10 Conferences were irregularly held at three to four year intervals, with 9 of these in regional centres of Australasia. It is only since 2012 that the Mill Operators’ Conference has become a regular biennial event, alternating with the MetPlant Conference.The number of people attending the Conference has more than doubled to 470 delegates at the 13th one in 2016. It has outgrown its regional beginnings.Papers presented to the previous Conferences have been analysed according to commodity, country of origin, technology and theme plus the affiliation of the authors to discern any trends that may assist in planning the future events.Suggestions are made as to how the AusIMM might wish to arrange its mineral processing/metallurgical conferences.Recent changes to the structure of the Conference providing a more meaningful experience for the delegates and increasing their interaction and involvement should be vigorously pursued.CITATION:Munro, P D, 2018. Mill Operators’ conferences – a 40-year retrospective and a vision for the future, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 5–14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

By D. Warkentin, M. Tomlinson, A. Nacu

"This study focuses on comparing the “blinding” effectiveness of various organic additives as part of a general review of using organic additives to mitigate preg-robbing and improve gold recovery during cyanide leaching of carbonaceous gold ores. The laboratory results compared the impact of various organic additives on the prevention of gold adsorption using both activated carbon and ore samples containing carbonaceous matter, generally referred to as total carbonaceous matter (TCM). Although several organic reagents were found to have a significant blinding effect on activated carbon, these results did not translate into increased gold leaching efficiencies with actual ore samples.INTRODUCTION Preg-robbing refractory ores, which contain carbonaceous matter, have been problematic in cyanide plants for many years. In industry, preg-robbing by carbonaceous matter may be mitigated using various techniques including flotation, to remove the carbonaceous matter; addition of blinding agents, to passivate the carbon surface and prevent adsorption of gold cyanide complex; roasting, to partially or fully destroy the carbonaceous matter; chemical oxidation (Abotsi & Osseo-Asare, 1986); pressure oxidation; or microbial deactivation (Dunne, Staunton, & Afewu, 2013). Carbon-in-Leach and Resin-in-Leach are also used as process alternatives in which activated carbon or resins are used to compete with the carbonaceous matter for gold cyanide adsorption. For highly preg-robbing ores, thiosulphate leaching may be considered as an alternative to conventional cyanide chemistry (Baláz, et al., 2000). Natural carbonaceous matter is composed mainly of hydrocarbons, organic acids, and graphitic/amorphous elemental carbon. Natural elemental carbon that behaves as activated carbon is considered to be the main reason for preg-robbing, although the true nature of this phenomenon is not fully understood (Tan, Feng, Lukey, & van Deventer, 2005). In general, the hydrocarbon fraction is assumed to have negligible interaction with gold, while organic acids, such as humic acids, may form complexes with gold, inhibiting its extraction in cyanide solutions. Organic reagents have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Abotsi & Osseo-Asare (1987) tested various organic compounds, with two possible effects in mind. First, the organic compounds were expected to adsorb onto the surface of the solids as anionic/cationic species; the resulting electrostatic interactions between the Au(CN)2- anion and the negatively/positively charged surface would inhibit/enhance the gold uptake. Second, the organic reagents were expected to coat the surface of the carbonaceous component in the ore, limiting the available adsorption sites and reducing gold losses. Optimal reagent dosage depends on ore mineralogy, maturity and surface area of the carbo"

Jan 1, 2019

By J. A. Mejia

The combination of high-resolution X-ray microtomography (HRXMT) image analysis and Lattice-Boltzmann Method (LBM) simulations has demonstrated the ability to describe real multiphase flow problems in fine coal filtration. The single component multiphase flow He-Chen-Zhang LBM model was used to simulate filtration with actual HRXMT images of pore network structures produced in filtration experiments. The analysis performed on coal, silica, and glass bead filter cakes showed that particle shape and wettability are two of the most important factors in the retention of moisture during filtration.

Feb 23, 2014

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By C. Brown, N. Rayyan, T. H. Dubaniewicz

Lithium-Ion batteries (LIBs) have the potential to go into thermal runaway which introduces a new ignition source in hazardous environments such as gassy underground mines that may contain methane in the surrounding air. Researchers from the National Institute for Occupational Safety and Health (NIOSH) used an accelerating rate calorimeter (ARC) to induce thermal runaway in individual lithium-titanium-oxide (LTO) and lithium-nickel-cobalt-aluminum-oxide (NCA) LIB cells within a sealed enclosure with either no methane, a lean, a stoichiometric, or a rich methane-air mixture in the surrounding canister to determine if these LIB types would ignite the methane, causing an additive effect on overpressures. Canister pressures and maximum temperatures reached by the cells, surrounding air, and exhausted gases were measured in this study and remained consistent with varying methane concentrations.

Feb 1, 2023

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott's paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By Joan K. Kuenzi

The purpose of this U.S. Bureau of Mines information circular (Ie) is to discuss how job analysis methods taken from different disciplines can be used together to form a more complete picture of jobs in the mining industry. "Job analysis" is a term used by many researchers, but use of the term is far from standardized. Authors of papers on this subject often state that there is confusion in how or why jobs are to be analyzed, what the resulting information is to be used for, and what the "job analysis" actually means. The process of breaking a job into elemental tasks and analyzing them is used to determine what skills and knowledge are needed to perform a given job, to improve efficiency, and to develop safer job procedures. All are valid reasons to analyze jobs, but the methods used to accomplish the analyses may be very different. In order to create a more complete picture of a job, it may be useful to incorporate methods and information from different areas of study rather than choosing one method for analysis.

Jan 1, 1995

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

By P. F. Sands

This U.S. Bureau of Mines report reviews the state of the art in blind pneumatic stowing of backfill in voids in abandoned coal mines. It contains a short history of the development of pneumatic equipment in mining and four recent case histories of blind pneumatic stowing. Limitations of pneumatic stowing in terms of equipment wear, costs, backfill material, and methodology are discussed, and some new procedures and designs are reviewed. A bibliography covering pneumatics in mining is included also. This report provides background for the preparation of a Bureau test program in which the variables affecting the efficiency of pneumatic backfilling will be studied using a full-scale surface test facility.

Jan 1, 1990

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

By D. Newman

Mineral production in the Highlands and Islands of Scotland during the last ten years has been confined to the sporadic production of industrial minerals—for example marble, anorthosite, limestone, talc and silica. From 1962 onwards there has been an upsurge in mineral exploration in the Highlands, increasing in tempo from 1966 onwards due to the efforts of the Institute of Geological Sciences, the Highlands and Islands Development Board, and private and public companies. Geological, chemical and economic aspects of some of the more interesting mineral prospects are discussed: these include anorthosite, feldspar, magnetite, quartzite and brucite marble. Reference is made to a geochemical survey undertaken in the Rosehall district of Sutherland, the results obtained being summarised. Problems that affect the future of mineral exploration in the Highlands are stated.

Dec 1, 1971

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By Will H. Coghill, C. O. Anderson

In July 1921 , we were assigned by the U. S. Bureau of Mines to an investigation of milling methods in the Tri - State zinc district ( Missouri -Kaneas- Oklahoma district ) . The work has progressed without interruption , and about onehalf of the funds allotted for it has been expended . This preliminary statement abcut the nature of the work and the results so far obtained , has been prepared for the information of the operators , and through their assistance to insure the greatest possible progress during the remainder of the work . A general survey of the district was made , and many of the mining companies cordially offered the facilities of their plants for the investigation . The work was finally centralized at the plant of the 0. M. Bilharz Mining Co. Its manager , F. H. Gartung, and his successor , O. W. Bilharz , have been especially helpful , also the millmen at this plant and elsewhere have rendered assistance without which the work could not have advanced . The Missouri School of Mines and Metallurgy , Rolla, Mo. , and the Miami School of Mines , Miami , Okla . , have given hearty cooperation . The Webb City Iron Works and the Joplin Supply Co. donated some necessary apparatus .

Jan 1, 1922

By Robert J. Hundhausen

During the early part of World War II , it appeared likely that supplies of chromite for United States industry might become critically short . As a part of the ensuing search for new sources of domestic chromite supply , the chromite - bearing black sands along the coast of southern Oregon were hurriedly investigated by State and federal agencies and by private interests , These investigations led to a decision to begin exploitation of the deposits immediately . A government stock- piling program was put into effect , a concentrator was financed by the Defense Plant Corporation , two privately controlled companies were encouraged to start mining operations , and the Bureau of Mines and the Geological Survey were authorized to search. for additional reserves of minable ore .

Feb 1, 1947

By Kenelm C. Appleyard

In introducing to an American audience a description of the work done in dry coal separation in England and in Europe generally, it is perhaps desirable to give a short history of the development outside the United States of the particular processes with which the author is connected, and perhaps to stress a little the differences in the nature of the conditions to be faced. England actually presents one set of problems and the Continent of Europe another, since the character of the coals to be treated is entirely dissimilar, and the attitude of the coal industries towards coal preparation is also dissimilar. England for generations has been working by hand good seams of clean coal of the highest possible quality and has not felt any pressing need to clean its coal. Most Continental countries, however, especially in Central and Western Europe, have been working friable and often very dirty coals for so long that a washery is accepted as a part of the normal equipment of a colliery, with the result that the art of wet washing has reached a high state of perfection, particularly in Belgium and Germany. The advent of machine mining has intensified the problems to be faced in all countries, and in England has been coupled with the working out of the best seams in the older coal fields, thus bringing about the necessity of working thinner and dirtier seams with resultant difficulties as regards marketing the products, while Poland, with clean and well prepared coal, has in recent years been attacking established British markets in Scandinavia. In recent years, therefore, interest in coal preparation has been steadily gaining ground in England, although it has not yet reached Continental dimensions. Broadly speaking, the differences in preparation problems between England and the Continent boil themselves down to one of size. In England, for example, with the exception of the Kent coal field, the proportion of coal of a size less than ? in. to the coal less than 2 in. is very much less than on the Continent, and since the principal difficulties in dry cleaning lie in the fines it is easier to produce good figures on

Jan 1, 1931

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933