Search Documents

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By Liang Sha

In this study, adsorption of copper by chemically modified orange peel was investigated. A conspicuous change occurs in the surface morphology of the biomass due to modification, which is depicted by SEM images. Equilibrium isotherms and kinetics were obtained and the effects of various factors, including solution pH, contact time, initial metal ions concentration and temperature, were studied by batch experiments. Kinetics was found to be best-fit pseudosecond- order equations. Equilibrium was better described by Langermuir isotherms rather than Freudlich isotherms. At 25?, pH5.30, the maximum adsorption capacity was 70.67mg?g-1 . With increase of temperature, adsorption efficiency decreased. The biosorbent was suitable for repeated use for more than five cycles.

Jan 1, 2009

This study of the tin-tungsten ore of the Shepherd and Murphy Mine, in central northern Tasmania, was originally undertaken at the request of the Moina Tungsten-Tin Mining Co., N.L., as part of the research programme of the Mineragraphic Investigations Section of the C.S.I.R.O. It is based on the examination of a suite of specimens supplied by the management, supplemented by a more extensive collection and observations made by the author during a short visit to the mine in October, 1956.The Shepherd and Murphy Mine is at Moina, 36 miles S.W. of Devonport and 22 miles from Sheffield, the nearest railway station. It was worked almost· continuously from 1893 to 1919, when a fire destroyed the mill; to that date it had produced concentrates to the value of £141,000. After a long period of idleness, the mine was re-opened by the present company, but it has been announced recently that unfavourable market conditions have again forced closure.GENERAL GEOLOGYThe mine is on a deeply dissected plateau, about 2,500 ft. above sea level; it lies between the Iris and the Forth Rivers, whose valleys are deep gorges cut to about 400 to 600 ft. above sea level. From Moina westwards to the Iris River, a limestone regarded as part of the Gordon River Group, of Ordovician age, conformably overlies a sandstone containing tubicolar casts which are circular in cross section, half an inch in diameter and up to two feet long, and which resemble marine worm burrows (Elliston, 1953).

Jan 1, 1958

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By J. U. MacEwan

THE basis on which the modern metallurgical industry is operated is the endeavour to attain maximum return in purchasing power for the least expenditure of energy. This has always been the general objective of the industry, as of all industries. In recent years, however, it has received a new emphasis. Today, as never before, increased attention is being directed to the detailed study of plant operations and the application of scientific knowledge and of business principles in order to achieve the maximum efficiency. This new emphasis is the result in large part of the new problems and conditions with which the industry has been confronted, chief among which are the following: (l) Development of new ore-bodies and the treatment of complex ores. (2) Necessity of achieving a greater degree of purity in some of the metals in order to meet the newly discovered demands for some of the industrial metals. (3) Discovery of new markets for many of the metals, either in pure form or in the form of alloys. ( 4) Change in values, absolute or relative, of some of the important metals. (5) Increasing scale of investment in expensive plant and equipment, which makes imperative most efficient utilization if total unit costs are to be kept to a minimum. (6) Increasing scale of operations in some important branches of the industry, which also makes essential maximum efficiency in organization, administration, and operation. The success with which the metallurgical industry has met the problems created by these changing conditions has been due primarily to the following factors: (1) Results of research and experimental work carried on by universities, government laboratories, and many private corporations in the industry itself. (2) Closet study of every detail of plant operation, both from the technological and from the economic point of view, with the object of increasing plant efficiency. (3) Interchange of information and experience amongst the operating companies. It is only by the concerted efforts of numerous investigators and experimenters that the underlying fundamentals of plant operations can be learned. The exchange of results permits their easy assembly and correlation with maximum benefit to the whole industry. Unnecessary duplication of research and experimental work is avoided and the industry as a whole is able to reap the fruits of this work with the maximum of-speed and efficiency. (4) Advances made in recent years in so-called 'scientific management' in industry as a whole and the application of the principles learned to the metallurgical industry. A review of the modern trends in extractive non-ferrous metallurgical processes illustrates the afore-mentioned new conditions and problems, and gives some idea of the methods by which they have been and are being surmounted.

Jan 1, 1937

By China University of Mining & Technology, Yuemin Zhao, Bo Zhang, Liang Dong, Zhenfu Luo, Chenlong Duan

"In China, approximately 65% of coal reserves are in the west region, where water shortage is a serious problem: high-efficiency dry coal beneficiation technology is desired. Using magnetic powder and fine coal as heavy medium, and using air as the fluidizing agent, a novel air dense medium fluidized bed separator is proposed for coal preparation. Coal can be efficiently separated according to density in the fluidized bed, where bed density is steady. The separator is highly reliable, the circulation quantity of heavy medium is low, and the gas distributor cannot be easily easily. The world’s first industrial modularized dry coal preparation plant was built by China University of Mining and Technology. Dry coal beneficiation technology was first used to produce low-ash coal. Results of industrial production show that the ash content of clean coal is 3.46%, the probable error E value is 0.055 g/cm3, and the organic efficiency is over 90%. The advantages of the modularized dry coal beneficiation system are the high separation accuracy, the simple process flow, the low operation cost, low energy consumption, and so on. This technology provides a new effective method for coal separation in acid region and coal tending to sliming.INTRODUCTIONCoal is the most important primary energy source in China, where coal output reached 3.68 billion tons in 2013 and represents approximately 68% of the primary energy consumption. Coal has made a great contribution to the development of the Chinese national economy, but it also brings serious environmental pollution. However, approximately 65% of coal reserves are in the arid west region in China where water shortages present a challenge for wet coal preparation technology. In addition, the abundant lignite resource, because it is easy to mud in the water, should not be treated with the wet separation method. Therefore, it is critical to develop highly efficient dry coal preparation technology to meet the demand in arid areas. Further, water resource shortages are a global problem, thus the development of efficient dry coal preparation technology in has potential application in other water-short countries like South Africa, Brazil, India and Turkey."

Jan 1, 2016

The paper presents a brief history of endeavours to start a mining education programme which began in the days when Papua New Guinea's first large mine, at Panguna (Bougainville), was coming into production. The status of the Public Investment Programme in Mining Engineering and the facilities being created for the education and training of Papua New Guinean citizens in mining and mineral processing are also described. Future expansion plans are also detailed including those for the commencement of petroleum engineering and geological engineering which would include courses in mining geology, exploration geology, engineering geology and petroleum geology. The paper also looks at the manpower training requirements in the lower levels of mining industry such as pit foreman, blasting foreman and other similar positions. It stresses the need to start mining technical training programs at pre- employment level and at certificate level in a technical college, possibly Lae Technical Colleqe.

Jan 1, 1991

By E Widzyk-Capehart

The mines of the future can be envisioned as complex, large-scale technological systems being operated remotely from few centrally located (major cities) operating centres and skeletal crew stationed at the site. These systems will require remotely located human operators to constantly adapt to new and unforeseen system and environmental demands. In addition, the remote operators will need to match system properties to the changing demands and operational conditions, ie must be able to handle the ‘non-design’ emergencies, because the system designers would not have been able to foresee all possible scenarios of failures and provide automatic safety devices for every contingency. Therefore, it is highly important that the operators’ job, which involves problem solving and decision making at the workstation level, is facilitated by the proper interface designs. This paper argues that decision support systems and thus human-system interfaces for the mines of the future should be developed based on the principles of human-system integration that take into account human information processing and cognitive abilities. The information presented to the operator must support the operator in taking appropriate action through a human-system interface designed according to scientific principles of User Centred Design. A case study is presented where an iterative design process was used by CSIRO researchers as an evaluation method involving users (control room operators) at several stages of the user interface design in order to correct any design inadequacies as they emerged. This process allowed the designers to identify any usability issues before the user interface was fully implemented, which subsequently enabled the control room operators to easily adapt to the new interface and carry out all designated tasks in a timely and effective manner.

Nov 22, 2011

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By M K. C Roberts, M G. Magwaza, J W. L Hanekom, P Piper, R Lousteau

Due to the perceived potential to extract the second economic manganese seam at its Black Rock Operations in the Northern Cape Province, South Africa, Assmang commissioned an investigation with respect to mining method and sequencing of the two orebodies in 2007. Based on this initial study into multiseam potential, conditions and impacts, the rock engineering aspect was expanded to determine conceptual rules to govern the extraction of both manganese seams using the normal bord-and-pillar layout implemented at this operation. This work included the theoretical analysis using basic pillar design practices and numerical modelling, including the use of Map3D, UDEC and Phase2 codes.In 2013, Assmang launched a large-scale investigation into the potential to increase mine output from all possible manganese sources at the operation. Included in this investigation was the requirement to confirm or modify the conceptual multiseam extraction rules to implementation. As part of this confirmation process, stress measurements, borehole camera audits and additional numerical modelling were performed at a particular site on the operation where a limited extraction of both seams had been undertaken. The results obtained from this process provided confidence in the conceptual extraction rules and allowed the derivation of final extraction rules that will be implemented at the operation as the multiseam mining process becomes more widespread.CITATION:Hanekom, J W L, Roberts, M K C, Magwaza, M G, Lousteau, R and Piper, P, 2014. Confirmation of multiseam extraction rules for Black Rock Manganese Operations, Assmang, Northern Cape, South Africa, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 107–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Mario Paredes Malca

El presente trabajo describe el sistema experto por circuito de molienda desarrollado en la Concentradora Toquepala, donde se aplica la tecnología del control experto-basada en conjuntos difusos y modelos matemáticos. Las ventajas que presenta la aplicación de los sistemas expertos comprenden el aumento de la capacidad de tratamiento, la disminución del costo de operación y del porcentaje del producto que no cumple las especificaciones. Asímismo, el sistema experto se integra al sistema de control para asistir al operador en la detección de los casos, donde las operaciones se puedan descontrolar, aunque ésta no sea realmente su principal función. Si se le configura y sintoniza correctamente, el sistema experto detecta, diagnostica en forma continua los problemas de operación y aplica modelos matemáticos y estadísticos de optimización, interactúando con un sistema de control DCS o PLC.

Sep 12, 2005

The Acid Drainage Technology Initiative (ADTI) was initiated in 1995 by federal agencies, the National Mining Association (NMA) and the Interstate Mining Compact Commission (IMCC) to identify, evaluate and develop cost-effective and practical acid drainage technologies. In 1999, ADTI was expanded through the addition of the metal mining sector, which is focused on drainage quality issues related to metal mines. ADTI addresses drainage quality issues from abandoned, active, and future coal and metal mines. The guiding principle of ADTI is to build consensus among industry, federal and state regulatory agencies on acid drainage technology development and technology transfer issues. ADTI is focusing its efforts on mine drainage prediction, sampling/monitoring, modelling and avoidance/remediation. ADTI is not a regulatory or policy development program. ADTI includes the Coal Mining Sector (CMS) and the Metal Mining Sector (MMS) under the overall guidance of the ADTI Operations Committee. The Operations Committee consists of representatives from industry, state and federal government and academia. The Coal Mining Sector includes two committees; a prediction committee and an avoidance and remediation committee. The Metal Mining Sector includes steering committee and work groups on prediction, sampling and monitoring, modelling, mitigation, and pit lakes. The Coal Mining Sector has produced two publications on the prediction and prevention of acid drainage. The Metal Mining Sector has workbooks under preparation covering the work group topics. This past winter, the Metal Mining Sector, working with the US Bureau of Land Management, presented a satellite training session on acid drainage. ADTI has evolved in response to changing needs and technologies as evidenced by the addition of the Metal Mining Sector in 1999. The Operations Committee and the members of the Coal and Metal Mining Sectors will guide future direction in response to identified issues.

Jan 1, 2003

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' Circular (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circular pros. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By A. Schaum

On average, there are approximately 10 fatal haul truck accidents per year. The most common causes for haul truck accidents include mechanical problems, inadequate training and insufficient road/berm maintenance. Due to the frequency and magnitude of haul truck accidents, new training methods are being investigated. With the widespread availability of computers and new technology becoming more reasonably priced, the ability to incorporate computer-based training for miners is becoming more possible. It has been shown that computer-based training is just as effective in knowledge acquisition as traditional lectures, and computer-based training can lead to a significant increase in the retention of material (Williams and Zahed, 1996). Studies have also shown that more engaging training methods lead to more effective knowledge acquisition (Burke et al., 2006). A supplemental system for current and new miner training to address the common causes of fatal accidents was developed. The training system is a virtual preshift inspection of a haul truck, and it can train new haul truck operators to identify parts that look defective. The training will increase an operator?s ability to recognize problematic parts and correctly identify the corrective action needed. Increasing the quality of training by providing an engaging, simulated hands-on environment will lead to safer behaviors by trainees, which will ultimately lead to fewer accidents and fatalities.

Jan 1, 2008

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By W. W. Weller

Heat capacity measurements of anhydrous cobalt sulfate (CoSO4), copper sulfate (CuSO4), nickel sulfate (NiSO4), and zinc sulfate (ZnSO4) were conducted over the temperature range 51° to 298° K. The results were used to evaluate the following entropies at 298.15° K (cal/deg mole): CoSO4, 28.1; CuSO4, 26.8; NiSO4, 24.8; and ZnSO4, 26.4. Entropies were combined with heats of formation to give free energies of formation.

Jan 1, 1965