Search Documents

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

Due to the reduction in frictional resistance, the characteristics of joint infill have a major role to play on rock mass instability. This paper elucidates the laboratory behaviour of graphite infilled joints based on a large-scale shear apparatus under constant normal stiffness (CNS). Discontinuities in a graphite mine have been simulated using high strength gypsum plaster, with the joints infilled with compressed graphite layers. The Fourier series was employed to characterize the joint surface, and the method of using the Fourier coefficients for the prediction of dilation and normal stress with displacement is explained. Die Charateristik von Verbindungsfüllungen hat einen wichtigen Einfluss auf Felsmassenstabilität aufgrund der Verringerung des Reibwiderstandes. Diese Veröffentlichung untersucht das Verhalten von Graphit gefüllten Verbindungen im Labormaßstab mit einer Methode die auf einem gross-umfang Apparateprinzip unter konstanter Normal-Steifheit beruht. Unregelmässigkeiten in einer Graphit Mine wurden mit Gypsum Gips von hoher Festigkeit simuliert, die Verbindungen wurden mit kompressierten Graphitschichten gefüllt. Fourier Reihen wurden angewandt um die Verbindungs Fläche zu Characterisieren. Die Methode die verwendet wurde um die Ausdehnung und Normalkraft mit der Verschiebung mit Hilfe von Fourierkoeffizienten zu bestimmen wird beschrieben. Due à diminution des résistances par frottements, les caractéristiques des joints de remplissage joue un rôle majeur sur les instabilités de la roche. Cet article étudie le comportement en laboratoire des joints de remplissage en graphite à partir d’un dispositif de friction à grande échelle sous rigidité normale constante. Les discontinuités dans une mine de graphite ont été simulées grâce à un plâtre à haute teneur en gypse, dont les joints ont été remplis de couches de graphite compressées. La caractérisation de la surface des joints a été réalisée avec les séries de Fourier. La méthode utilisant le coefficient de Fourrier pour la prédiction de la dilatation et de la compression en fonction du déplacement est également expliquée.

Jan 1, 2003

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

The 1981 Review: In the late 1970s there was an upsurge of interest in the prospecting and mining of this countryÆs mineral resources. That upsurge of interest was accompanied by a mounting public concern over the damage mining operations might do to the environment. Concern was also expressed about what some people perceived as inadequacies in the legislation which regulates mining and the grant of mining privileges, and inconsistencies in the relationship of that legislation to other legislation regulating land use and the use of resources.

Jan 1, 1984

By Anselmo Monteiro Ilkiu

No presente trabalho será apresentado um modelo matemático para a análise da instabilidade plástica de um cilindro de parede fina sujeita a pressão interna, considerando o material com anisotropia normal R no estado plano de tensões. As equações foram obtidas, com base nas teorias elásticas e plásticas, considerando o critério de escoamento de von Mises no estado plano de tensões em termos da anisotropia normal, e de acordo com os trabalhos realizados por Johnson & Mellor [1], Chakrabarty [2] e Al-Qureshi [3].

Aug 16, 2017

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary. The strategic minerals investigations of the bureau afford an example of this change in emphasis to problems of immediate and urgent interest, and during 1941 they comprised, upon the basis of appropriations and expenditures, more than 90 percent of the work of the division.

Jan 1, 1941

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest: those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary.

Jan 1, 1941

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

El presente texto señala los factores y la teconología para controlar adecuadamente el medio ambiente subterráneo en el curso de los próximos diez años. En ese sentido, se muestra el control de las dimensiones físicas, el calor, los gases, la humedad, la ventilación de la mina, supresión de polvo, iluminación, ruido, esfuerzo físico y movilidad y el futuro transporte subterráneo.

May 1, 1981

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By Haskiel R. Shell

Methods of chemical analysis of clays for the following constituents are presented: moisture, ignition loss Fe2O3, TiO2, P2O5, CaO, MgO, Na2O, K2O, total. carbon, carbonate carbon total sulfur, soluble salts, and soluble sulfate. In these procedures the attainment of accuracy has been the primary consideration sample was taken to insure accuracy, with ordinary precautions. The procedures may therefore be somewhat somewhat and will not be suited for routine work on samples for which the approximate analysis is already known and in which the need for accuracy is not very exacting. However, the method shod be as a set of detailed directions, that have been tested and shown to yield accurate results with clays and other aluminum silicate minerals. Among these minerals are clays of all types, bentonite bauxite, shale, brick; soil, calcined refractory, and sand. Although some of the methods are Unusual, no particular claim is laid to originality. The material was drawn frail many sources, put together and tested.

Jan 1, 1949

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905