Search Documents

By Tyler DB, Thin LGT

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications are made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a new squat pillar empirical strength relationship.

Jan 1, 1992

By Silas C. Nichols, Jennifer E. Nicks

"Limit states design (LSD), or load and resistance factor design (LRFD), is a method to account for the uncertainty in loads and resistance through a reliability calibration that requires all applicable limit states (strength, service and extreme) to be checked during foundation design. LRFD has been in use internationally for several decades; however it wasn’t until recently that engineers working on highway projects were required to use the method for the design of highway bridges and other appurtenances. Although the bridge community has been using a form of limit states design for structural components since the early 1970s, the design of foundations for bridges, walls and other geotechnical features had long been performed using allowable stress design (ASD), whereby all uncertainty in loads and material resistance is combined in a single factor of safety. While the move to LRFD was viewed as a more rational approach for the design of bridges and structures, the transition to its use for geotechnical engineering has been met by many with confusion and difficulties in application. This article will revisit the history of transition from ASD to LRFD for geotechnical engineering, summarize the status of the transition and issues with its use, and briefly discuss some emerging research opportunities for improving and advancing the design platform.Background and HistoryUntil about a decade ago, foundations and substructures for bridges were traditionally designed using ASD, while the superstructure was designed using load factor design (LFD), a precursor to LRFD that incorporated factored design loads but no risk assessment. This combination led to uncertain and incompatible safety margins in design for the various bridge components. In 1986, the American Association of State Highway Transportation Officials (AASHTO) Subcommittee on Bridges and Structures (SCOBS) concluded that the standard bridge specifications in use at the time for U.S. transportation projects had significant inconsistencies and gaps, wasn’t up to date with emerging technology and that the development of new specifications was warranted. The proposed solution by the subcommittee was to transition to a more coherent method of design where applicable failure and serviceability conditions could be evaluated considering the uncertainties associated with loads and resistance."

Jan 1, 2015

By Yu Chen, Charlie C. Li

The application of rock bolts for the stabilisation of underground openings needs a good understanding of the response of the bolts during rock excavation. The pull-and-shear performance of two types of rock bolts—that is, the fully encapsulated rebar and the D-Bolt—has been studied both experimentally and numerically. The rock bolts were tested under a pull-and-shear load at five displacing angles (i.e., 0°, 20°, 40°, 60°, and 90°), and at the same time, the strains on the bolts were monitored during testing. The two types of rock bolts have similar loading capacities, while the loading angle has obvious influence on the deformation capacity of the D-Bolt. The ultimate total displacement of the D-Bolt decreases from 140 mm under pure pull loading to 70 mm under shearing. The displacement capacity of the rebar is not significantly influenced by the loading angle but remains at a quite low level from 29 to 53 mm. The D-Bolt yielded in a longer section the rebar bolt under pure shear. A trilinear material model was used to simulate the strain hardening behaviour of the bolt steels in the numerical code FLAC3D. The numerical results show that the axial load in the bolt decreases exponentially with the distance from the loading position for the rebar bolts, but it remains constant in the bolt sections between the anchor positions for the D-Bolts. When the bolt is subjected to a lateral load, shear stresses are created on the D-Bolt surface within a short distance from the loading position.

Jan 1, 2015

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By J. S. Coffman

Wyoming is estimated to have more than 700 million tons and Utah more than 2.5 billion tons of +10 percent P2O6 phosphate rock considered to have some future economic potential. In Wyoming, the +24 and +18 percent P205 rock potential resources total nearly 250 and 450 million tons, respectively. In Utah, the +31, +24, and +18 percent rock total approximately 33 million, 222 million, and 2.2 billion tons, respectively. These resources are all located above the local drainage levels and do not include latent resources. All of the mining and beneficiation of phosphate rock in the two States is done by San Francisco Chemical Co. The facilities include open pit mines at Vernal, Utah, and Leefe, Wyo.; an underground mine in the Crawford Mountains, Utah, and beneficiation plants at Leefe and Vernal. One of the principal markets for the phosphate rock is Western Phosphates, Inc., fertilizer plant at Garfield, Utah. Recent exploration and development has been under-taken by different companies in the Southeastern Wind River Range, Sublette Range, and Crawford Mountains. The facilities at Leefe and Vernal are in the process of expansion. Some of the areas of western Wyoming contain vast quantities of phosphate rock in minable units, but, because of their remote location, are classed as latent areas. In these areas, there are estimated to be about 700 million, 2 billion, and 3 billion tons of phosphate rock in the +24, +18, and +10 percent P205 grade classes, respectively. The Snake River Range of Idaho and Wyoming is also estimated to contain roughly 21, 106, 177, and 214 million tons of potential resources in the +31, +24, +18, and +10 grade categories, respectively. This area also contains a large amount of latent rock in the more remote areas.

Jan 1, 1967

By George S. Rice

STUDIES of ground movement and subsidence caused by mining necessarily chiefly deal with causes and effects of making extensive excavations underground with spans beyond the strength of the un- supported or temporarily timbered roof or hanging wall. Perhaps no other phase of engineering is so de- pendent for results upon the assemblage of what may be called "experience data." That this is the case is cot surprising when one considers the number of variables involved in any at- tempted mathematical formula to determine the angle of draw or the angle of permanent slope of the rocks in any particular case. It is not like dealing with construction materials in which, through testing of. small specimens, in conjunction with the tests of large built- up specimens, relative stresses and strains may be deter- mined and formulas closely approximated for still larger constructions.

Jan 1, 1931

By R. Kumar, A. K. Verma

"In this paper, an anisotropic shear behavior of rock joints is investigated under constant normal load condition (CNL). The natural rock joint roughness is transferred to artificial rock samples using room temperature vulcanizing (RTV) silicon rubber. Artificial cylindrical rock joint samples (90 mm diameter and 50 mm height) are made by mixture of cement, sand, and water in the ratio of 1:1.5:0.45 (by weight). Direct shear tests are conducted on these samples in twelve directions at 30º apart at four different normal stresses (250kPa, 500kPa, 1000kPa, and 1500kPa). Thus, 48 samples are tested in laboratory. Test results shows that the peak shear strength (?) of rock joints is anisotropic in nature due to change in morphological features in particular shearing direction. Joint roughness coefficient (JRC) is determined in each shearing direction by trial and error method using Barton’s model (1973). Further, cohesion ( c) and angle of friction ( ? )of joint surface in each direction is determined. Finally, a relationship between angle of friction ( ? ) and joint roughness coefficient (JRC) is developed. Experimental shear strength and Barton’s shear strength is compared and it is found that effect of anisotropic decreases with increasing normal stress. INTRODUCTIONRock mass is generally composed of discontinuity which refers collectively to joints, faults, bedding plane and folds etc. ISRM (1978) defined joint as a line of break of geological origin along which there is no visible displacement. Joint is three dimensional discontinuity which composed of two matched/mismatched surfaces. The presence of joints in rock mass plays an important role to define its overall shear strength, deformability behavior, in-situ stresses and hydro-geological properties. The shear strength of rock joints is important in the design of near surface/ deep geotechnical works (mining excavation, dam foundation, power plants, underground caverns, and slopes).In last 40 years, many constitutive models are developed to predict shear strength of rock joints under CNL conditions (Patton 1966; Landanyi and Archambault 1969; Barton 1973; Goodman 1976; Barton and Choubey 1977; Plesha 1987; Desai ad Fishman 1991; Amadei and Saeb 1992; Maksimovic 1992; Wibowo et al. 1993; Huang et al. 1993; Amadei et al. 1998; Indraratna 2000; Homand et al. 2001; Wang et. al. 2003; Samadhiya et. al. 2008; Asadollahi and Tonon 2010; Ghazvinian et al. 2012). These constitutive models have limitations to predict shear strength of rock joints in one direction. Till date, among all constitutive models, Barton (1973) model is widely used in practice due its simplicity. It includes parameters such as joint roughness and joint compressive strength (JCS) to quantify joint surfaces."

Jan 1, 2015

By W. H. Emens

[This circular is one of a series dealing with tie development and equip¬ment of small and medium size mines, and with the costs of such work prior to productive operation. The preparation and publication of these papers by the Bureau off Mines has been made possible through the cooperation of various min¬ing and development companies. The bureau of Mines has published a series of circulars dealing with min¬ing methods and costs at a large number of producing nines in the United States, Canada, Mexico, an, other countries. Unit costs of development work, shaft sinking, (rifting, crosscutting, tunneling, and raising are usually much higher in the preliminary development of a property than during its productive life.]

Jan 1, 1933

By Carlos Guimaraes, Jefferson Klug, Raquel Verona, Pablo Leão, Miguel Arcanjo Almeida, Carlos André Ruy Carneiro, Marcos Daniel Gouveia

O cenário de perda de produção devido a quebras de sequência por obstrução em aços acalmados ao alumínio com tratamento com cálcio apresentava-se crítico para a Aciaria. Foram realizados ajustes técnicos nos processos de refino primário e secundário através da implementação de ações para redução do consumo de alumínio, ajuste da composição química da escória de panela e ajuste do procedimento de adição de cálcio. A mensuração dos indicadores que suportaram o resultado final foi através de gráficos ternários de escória, contagem de inclusões, analise de oxigênio total, analise da distribuição química de inclusões via MEV/EDS, janela de lingotabilidade e alumínio dissolvido. O desenvolvimento do projeto alcançou uma consistente redução do índice de obstruções aliados ao aumento da limpidez e qualidade dos

Oct 1, 2019

By Bharat Garg

The coking coal or clean coal from raw material division, Tata Steel Ltd. is a prime source of energy for inhouse steel making. Coal reserves of semi soft coking coal at West Bokaro is beneficiated by dense media cyclone and froth flotation processes to produce clean coal. In dense media cyclone process two byproducts-middling and rejects are also produced along with clean coal. With the growing demand for clean coal, it becomes imperative to maximize the recovery of clean coal in beneficiation processes. This will help, not only in reduction in cost of production, but also in raw resource conservation, and proper utilization. In this context, a case study was conducted at West Bokaro to identify opportunities for clean coal recovery from by-products. This paper mainly discusses the process for recovery of clean coal from byproducts and study of further liberation of clean coal from byproducts for economic consideration.

Sep 1, 2012

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By Bo Hyun Kim, Mark K. Larson

This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock-mass behavior in longwall coal mines in highly stressed, bump-prone ground. The floor-heave and nofloor- heave phenomena at a western US coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria (i.e., Mohr–Coulomb or Hoek–Brown failure criterion). The previous numerical study demonstrated these phenomena using a user-defined model of the s-shaped brittle failure criterion in conjunction with a spalling process in the FLAC3D numerical modeling software. The results of the FLAC3D modeling agreed with the observations of the relative amounts of heave from each gate-road system. However, the FLAC3D model adopted many assumptions and simplifications that were not very realistic from a physical or mechanical perspective. To overcome the limitations of the FLAC3D model, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. The effect of stress rotation in the mining-induced stress field was considered by using a different geometry of rock fractures in the coal seam. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) were also considered by using Monte Carlo simulations. Consequently, the 3DEC models using the DFN technique resulted in predictions of floor heave that agreed with observations of the relative amounts of heave from each gate-road system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Apr 14, 2022

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached to extract gold. The main aim is to decrease the arsenic content in processed materials and to break up the ore lattice, thus liberating the gold. Some regulations were established by authorities for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot plant testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum, arsenic is sublimated into elemental and sulfide forms. This process allows for the minimization of the negative influence on the environment, but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and it may be carried out in fluid bed furnaces.Oxidizing roasting of the concentrates in the presence of soda results in formation of water-soluble compounds and forces practically all arsenic and sulfur to remain in the cinder."

Jan 1, 2003

By Robert S. Hedin

Passive methods of treating mine water use chemical and biological processes that decrease metal concentrations and neutralize acidity. Compared with conventional chemical treatment, passive methods generally require more land area, but use less costly reagents and require less operational attention and maintenance. Currently, three types of passive technologies exist: aerobic wetlands, organic substrate wetlands, and anoxic limestone drains. Aerobic wetlands promote mixed oxidation and hydrolysis reactions, and are most effective when the raw mine water is net alkaline. Organic substrate wetlands promote anaerobic bacterial activity that results in the precipitation of metal sulfides and the generation of bicarbonate alkalinity. Anoxic limestone drains generate bicarbonate alkalinity and can be useful for the pretreatment of mine water before it flows into a wetland. Rates of metal and acidity removal for passive systems have been developed empirically by the U.S. Bureau of Mines. Aerobic wetlands remove Fe and Mn from alkaline water at rates of 10-20 and 0.5- 1.0 g. m-2? d-1, respectively. Wetlands with a composted organic substrate remove acidity from mine water at rates of 3-9 g. m-2? d-1?. A model for the design and sizing of passive treatment systems is presented in this report.

Jan 1, 1994

By Antonio Fernández, Javier Cáceres, Enrique Ramírez, Camila Yepez

El sector minero es una de las pocas industrias que depende de los precios de mercado para producir. Por lo cual, mantener ventaja competitiva y garantizar la eficacia del proceso para alcanzar las metas propuestas por la empresa minera representan un desafío constante. Esta investigación tecnológica tiene como objetivo maximizar la eficacia en los procesos de transporte y perforación manteniendo los costos más bajos en su proceso productivo. La investigación presentó dos desafíos durante la etapa de prueba que fueron la especialización del personal y modificación progresiva de los equipos para cada actividad específica.

Sep 30, 2022

By B Hannah, M Uriarte, F Labarca, C Madore, G Ganapathi, L Martin, T Haase

BechtelÆs Mining and Metals projects across the globe are executed in remote arid and semi-arid countries where providing even basic water supplies impose considerable challenges. Opportunities for water conservation measures using a Six Sigma initiative were proactively pursued to address the potential business impacts of limited availability of water resources. The initiative investigated areas driving water-optimisation during concrete operations and camp management. This paper details the water conservation evaluation of alternatives and cost/benefit analysis based on current and predicted water usage for development projects. Optimisation of water consumption through institutionalising more prescriptive standards for camp design and defining water conservation requirements have resulted in a new standard specification. Based on our projected mining project workload across the globe, it is estimated that for the period 2012 - 2015, a potential 5.5 M m3 water savings resulting in US$11 M could be realised for construction camps and savings of 4 M m3 of peripheral concrete process water resulting in potential cost savings of US$8 M could be achieved as a result of these revised standards.CITATION:Haase, T, Hannah, B, Ganapathi, G, Martin, L, Madore, C, Labarca, F and Uriarte, M, 2013. Water conservation at construction projects, in Proceedings Water in Mining 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Leandro Augusto Justen Marzulo, Guilherme Lucio Abelha Mota, Otávio da Fonseca Martins Gomes, Gilson Alexandre Ostwald Pedro da Costa, Alexandre da Costa Sena, Felipe Schimith Batista

O presente trabalho desenvolveu uma solução, utilizando Hadoop e Map Reduce for C (MR4C), capaz de paralelizar a segmentação de fissuras em imagens de partículas minerais. Um conjunto de 221 imagens de tamanhos distintos de partículas de minério de cobre obtidas por microscopia eletrônica de varredura foi utilizado para os testes. A variação do número de nós de processamento apresentou um ganho do tempo de execução que escalou de forma quase que linear. O balanceamento de carga estática promoveu um speedup de 1,3. A solução proposta, quando comparada à implementação sequencial, considerando um cluster com 9 nós de processamento, atingiu um speedup de 19,1.

Oct 1, 2019

By W. W. Adams, T. D. Lawrence

"Despite the manpower shortage and other difficulties of operation in war time, the National Safety Competition of 1943 for the promotion of safety in the mineral industries of the United States was notable for having a larger enrollment of mines and quarries than in any other year except 1941 and 1942 since the yearly safety contests were inaugurated in 1925. The competition was also notable for having a larger number of man-hours represented by the competing companies than in any previous contest except that of 1942. The ratio of accidents and days of disability resulting from accidents to the number of man-hours of work performed was more favorable than in 1942; the accident-frequency rate was lower and therefore better than in 13 of the 19 years during which the annual safety competitions have been conducted, and the accident-severity rate was better than in 16 of the 19 years.The National Safety Competition is a yearly safety contest conducted by the Bureau of Mines, United States Department of the Interior. Companies that win first place in their respective group in the contest are awarded a bronze trophy, ""The Sentinels of Safety,"" which is provided by THE EXPLOSIVES ENGINEER magazine. Competing companies are segregated into six groups: Underground bituminous-coal mines, underground anthracite mines (in Pennsylvania), underground metal mines, underground nonmetallic-mineral mines, open-cut mines (without regard to kind of mineral produced), and open quarries (without regard to kind of stone produced). The bronze trophies are retained by the six winning companies for 1 year and are then transferred to the winners of the succeeding year's contest. On the pedestal of each trophy is engraved the names of the winners of the trophy. With the award of the trophies for 1943, therefore, the pedestal of each trophy bears the names of 19 winners."

Aug 1, 1944

By B. J. Keating

"AT PRESENT, it is not certain that any of the sulphide de in the Province of Nova Scotia attain the lower grade limit of 60 per cent sulphides over the minimum area of 1,000 square feet suggested as cut-off specifications for inclusion in this Symposium. However, several of them do include massive sections of substantial size and others represent concentrations of sulphide material that are well above average. It is felt, therefore, that a tentative classification of the deposits and presentation of their geological settings are justified and may help round out the genetic aspects of this study. Accordingly, data considered to be the most pertinent are assembled here in the event that some may fit into larger-scale patterns of mineralization that may take shape as a result of this investigation.The three principal massive sulphide deposits in Nova Scotia are the Stirling, the Smithfield, and the Walton. The locations of these are shown on the accompanying key-map (Figure 1).Three other deposits, the locations of which are also indicated on the map, are the Meat Cove, Rocky Brook, and Gays River de¬posits. Although these fall far short of the minimum dimensions and grade specifications referred to above they are singled out because they have received more than passing attention and are illustrative of the mineralization types to which they belong."

Jan 1, 1960

By Thiago Pinto Silva

Este estudo teve como objetivo investigar o efeito da substituição da dolomita por magnesita como fonte de MgO no processo de sinterização. Em testes realizados em escala piloto, observou-se que a utilização de magnesita eleva a resistência mecânica do sínter. A diferença de resistência foi decorrente da formação de uma solução sólida entre magnésio e ferro durante a sinterização. No caso da dolomita, que é fonte tanto de cálcio quanto de magnésio, a solução sólida Mg-Fe promove o encapsulamento do cálcio no seu interior, o que dificulta a formação das fases mineralógicas que promovem o endurecimento do sínter. Assim, a participação do cálcio na formação das fases ligantes é inibida, limitando a resistência mecânica obtida. A magnesita, por sua vez, não apresenta cálcio em sua constituição, sendo esse elemento adicionado via calcário. Dessa forma, o efeito do encapsulamento do cálcio não ocorre, havendo grande disponibilidade desse elemento para a formação de fases ligantes, permitindo a obtenção de níveis mais elevados de resistência mecânica do sínter. Portanto, a substituição da dolomita pela magnesita mostrou-se viável, desde que a granulometria seja similar à da dolomita, com grande potencial de melhora produtiva da sinterização industrial.

Oct 30, 2017