Search Documents

. F. W. SPERR, JR.,* Pittsburgh, Pa.--Mr. Malcolmson states that the Carbocoal process produces ammonium sulfate in excess of that normally recovered in the ordinary byproduct coke process. Table 3 indicates that 20,000 to 25,000 lb. of sulfate of ammonia are obtained in carbonizing 1000 tons of Clinchfield coal. This is a high-grade coal and yields from 26 to 28 lb. of ammonium sulfate per ton in a modern byproduct coke oven. On the next page, 21 lb. is stated as the yield of ammonium sulfate per short ton of raw coal; this is less than the average production from any well operated byproduct coke-oven plant treating coal of the character usually coked, in Pennsylvania and Ohio. The statement as to the comparative yields of light oil is somewhat misleading in view of the results obtained during the past year or two by the more modern byproduct coke plants. The plants put in operation by the H. Koppers Co., during the past two years, are producing about 3.5 gal. of light oil per short ton of coal, and several of these plants are producing more than 4 gal. per ton. The yield of pure toluene runs from 0.45 gal. to 0.55 gal. per ton. .The quality of the light oil .obtained from the Carbocoal process is of much greater importance than would be inferred by one not closely familiar with the subject. The presence of paraffins in the benzol and toluol fractions seriously detracts from their commercial value; the benzol and toluol fractions derived fro in the Carbocoal process contain about 50 per cent, of paraffins. It should be thoroughly understood what these paraffins are. They are simply hydrocarbons that go to make up ordinary petroleum, and if a successful method for the removal of paraffins from benzol and toluol has been developed, this can at once be applied to several well known processes by which benzol and toluol can be made directly from petroleum, which have as yet been total failures on account of the contamination of these products by paraffins.

Jan 11, 1918

By K. R. Price, M. Gauna

A high seam geologic condition exists at Jim Walter Resources No. 4 mine that requires immediate rib support after a continuous miner cuts a place. High seam mining heights are typically 2.4 to 2.6 m (8 to 9 ft) and a thick rock layer is present in the upper portion of the coal rib side. The 610-m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 305 mm (12 in.) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas that endanger men and equipment. To control this, rib support must be installed in the roof bolting operation as the bolting crew works toward the face. A rib control system has been developed for this high seam mining condition using a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDM-15 bolting machine. More than 120 km (75 miles) of entry have been supported with angle rib bolts. These angle bolts constitute 43% to 60% of the total roof and rib bolt footage in the high seam portions of No. 4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method using bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people. Total drilling supply costs are about 60% the previous cost, when compared to the previous support method using horizontal rib bolts:

Jan 1, 1985

By H. E. Rorschach

Oil-field activities in Oklahoma made 1936 the best year since 1930. Approximately 2800 wells were completed, an increase of about 20 per cent over 1935. Purchasers' reports filed with the Corporation Commission showed a total of 200,240,252 bbl. of oil purchased from leases in 1936. The assembly of a complete table of the oil fields of the state was not achieved, as many of the early records of operators and pipe-line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. The outstanding developments of the year were: the discovery of rich Wilcox-sand production in the Moore pool; the spectacular drilling campaign in the Capitol or Mansion extension in the Oklahoma City pool; the surprising extension of the Olympic pool and the Hunton lime zone in the Fitts pool; and the failure to find more Ordovician production in southern Oklahoma. Wildcat discoveries, which were on a par with 1935, resulted in the discovery of such promising pools as Billings-Wilcox, North Bethel, North Earlsboro and North Lucien. The Fitts-Upper Simpson, Edmond, Jesse, Keokuk Falls and South Burbank pools underwent considerable development. Fitts Pool.—The Fitts area in Pontotoc County was greatly extended during the year and was the leader in drilling activity in the state. The producing limits were pushed to the east and north and the development of the Hunton lime horizon was outstanding. In the Upper Simpson zone 162 wells were completed; 137 in the Hunton lime zone and 26 in the Wilcox zone. The Oil Creek zone, a sand body below the Wilcox member, was discovered by the Magnolia-Statler No. 3 well located in the 1/4. 1/4 of sec. 28-2N.-7E. Moore Pool.—The Moore pool, in Cleveland County, which was opened in 1935 by the Sinclair Prairie-Franklin Community No. 1 well, surprised the oil industry when the Sinclair Prairie-Marvel No. 1 well, on Apr. 1, 1936, discovered a rich body of Wilcox sand below the distillate

Jan 1, 1937

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes hack well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948. Summary Of the eight million tons of coal mined in the two states in 1947. ap- proximately two million tons were washed in wet washing plants, using concentrating tables or jigs. The one table plant accounted for 70 pct of the output of washed coal, and two large Baum jig plants accounted for an additional 26 pct, leaving only a small residual tonnage to be accounted for by other types of jigs The necessity for washing coal is occasioned by the desire or necessity of reducing the ash content of the coals— sulphur is not a problem in this area. All washeries, except the table plant, are at or near the tipple, hence wash only one kind of coal. At the table plant a large number of different coals are washed. Only at the table plant is there any occasion for drying any considerable quantity of fine coal— other plants size and/or dewater on shaking screens. The results of washing at the smaller plants are judged by the number (or lack) of complaints about the quality of the washed coal. This is probably as good a system as can he devised for small, intermittent operations. The efficiency of the Baum jig ap-pears to be quite high. This is to be expected as long as the automatic control of the refuse gate operates properly. The efficiency of the concentrating table is not as high as that of the Baum jig, especially when the "difficulty" of washing is taken into consideration. When dealing with coals in which the "bone" is larger than the "coal," the table appears to be at a definite disadvantage, because of its sizing action.

Jan 1, 1950

By Carleton C. Long, George F. Weaton

Two years ago the general features of the St. Joseph Lead Company's zine-smelting process were described.' At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtowlz smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the company's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; SiO², 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the coacentrate to a calcine of average conlposition (first 10 months of 1938): Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; SiO², 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07'; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sulphuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in, by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO² to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1943

By F. Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimoniallead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1944

By George F. Weaton, Carleton C. Long

Two years ago the general features of the St. Joseph Lead Company's zine-smelting process were described.' At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtowlz smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the company's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; SiO², 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the coacentrate to a calcine of average conlposition (first 10 months of 1938): Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; SiO², 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07'; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sulphuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in, by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO² to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1943

By C. S. Anderson

Georgia, since 1829, has produced nearly $18,000,000 from her gold mines, but in late years the output has dwindled to insignificance. In view of present universal efforts to increase gold production, it seems pertinent to record some recent observations in that field, briefly review its past and weigh probabilities of reviving gold mining there. Little in this paper can be claimed as new or original, and it does not present results of a detailed or profound investigation of the whole region. The Allatoona gold mine was reopened in January, 1932, and explored at greater depth during the period from January to June of that year. A number of other abandoned mines were visited, but since the workings, in common with most such mines in Georgia, were flooded or caved, underground conditions could not be examined. For a wider knowledge of the subject, a search was made through available pertinent literature and statistics, a bibliography of which is appended hereto. To all the sources obligations are gratefully acknowledged. Production The discovery of gold in Georgia, in 1829, led to an influx of 6000 to 7000 miners and a production of over $200,000 in the following year. A branch of the United States Mint, established at Dahlonega in 1838, accounted for $6,115,569 up to the time of the Civil War. The output fluctuated greatly from year to year, with an all-time peak of $582,782 in 1843. In only one other year, 1845, was the half million mark exceeded. After the war mining began again, but 1883 is the last year for which an output of $200,000 is reported. Placers, always the main source of production, were yielding less and less, and in spite of increased quartz-mining activities the downward trend continued. The last year in which there was a production of $100,000 was 1902. In 1914, $16,270 came from 26 placers and 11 deep mines, with the latter reporting 1750 tons of $3 average value. In 1925, one placer and four lode mines that mined 8100 tons assaying $1.19 per ton produced $9500. One placer and one quartz mine, operating in 1930, reported a total output of $4194. Table 1 pictures the waning output.

Jan 1, 1934

By A. Josefsson

The transition temperatures of 0.01 to 0.02 pct carbon steels are shown to be strongly influenced by cooling rate in the a range, quenching from A, causing a very low transition temperature even after strain aging. In a titanium-stabilized steel and in a steel with 0.05 pct C this effect is absent. NORMAL mild structural steels usually show a structure of more or less pure ferrite, as a matrix, in which cementite grains or pearlite are embedded. Of these components, ferrite is by far the most interesting one as far as ductility and brittle (cleavage) fracture are concerned. Obviously, pear-lite and carbide are by no means necessary for a cleavage crack to nucleate and grow in the ferrite, as steels with a very low carbon content (Armco iron with 0.02 pct C) have an impact transition temperature just as high as semikilled steels with 0.26 pct C.1 Although it has been argued that a very embrittling effect is to be expected from cementite, precipitated as continuous films along the ferrite grain boundaries,'. " the micrographic evidence for a direct causal connection between the brittleness and these films does not seem to be very convincing. On the other hand, it has been stated that cementite particles in ferrite are able to stop ferrite cracks.4,5 In any case, the properties of the ferrite itself seem to be of overwhelming importance to the ductility of steels, justifying a thorough study of steels consisting of ferrite of different compositions, but principally free from pearlite, which means a carbon content below 0.02 pct. Such investigations have been carried out using the impact transition temperature as a criterion of the tendency to brittle fracture and have given some rather unexpected results. One result is the profound influence of carbon on the transition temperature of the steel in normalized condition. If the carbon content is reduced from 0.02 to 0.015 pct and below, a nearly discontinuous decrease in transition temperature appears even with high percentages of such elements as phosphorus and nitrogen present. This will be reported elsewhere." The present paper deals with another effect of carbon upon transition

Jan 1, 1955

US 4,132,635 -In the froth flotation beneficiation of low- grade siliceous iron oxide ore, an aqueous pulp of undeslimed ore is conditioned first with a reagent formed by incorporating a water-soluble polyvalent metal salt into an aqueous solution of sodium silicate and then with oleic acid or other anionic collector and optionally pine 011 or other frother. The conditioned pulp is subjected to flotation to concentrate Iron oxide values in the froth D. C. Yang, assigned to Michigan Technological University Jan 2, 1979 7 pp (209-1 66) Filed 1-1 3-77 (759,094) Drawing below.) [ ] US 4,133,038-In the froth flotation beneficiation of copper sulfide ore or other ores, an aqueous suspension of a mineral sample of uniform grain size and composition is conditioned with a strongly adsorbable collector in an amount which is a fraction of the amount sufficient to create a monomolecular layer on the mineral grains, and the conditioning continued until the entire amount of collector is adsorbed The conditioned pulp is subjected to flotation, the floated particles separated at timed intervals, and the flotation rate coefficient determined. By varying the degree of adsorption in repeated treatments, the dependence of the flotation rate coefficient on the degree of adsorption may be determined A Nieml Jan 2, 1979 10 pp (364-502) Filed 12-7-77 (858,353) Priority Finland, 5-26-75 (75/1,525) Same: British 1,533,723, dated Nov 29, 1978 Same Canadian 1,065,066, dated Oct 23, 1979 US 4,133,746System and method for maintaining substantially steady state conditions in the froth flotation beneficiation of copper ore, molybdenum ore, or other metal ores The mass flow of flotation concentrate from the cell is monitored continuously, and the rate of admission of aeration air into the pulp in the cell is varied inversely with respect to variations in the mass flow control of rougher flotation cells is accomplished with a single valve G W Dopson, assigned to Magma Copper Co Jan 9, 1979 6 pp (209-1) Filed 11- 23-76 (744,306

Jan 1, 1980

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By Robert S. Baker

It has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformiation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta) (alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It, is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850" C. in iced brine at -8" C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 35.60 per cent zinc (9812 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1932

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or 'a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By P. A. Beck, L. J. Demer

As reported in a previous publication,' isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949

By V. S. Melamud, A. G. Bulaev

"Sulfide ore processing is characterized by significant losses of metals, for example, with flotation tailings. Therefore, flotation tailings can present an important source of metals. The treatment of flotation tailings is a technological issue due to low content of valuable metals (e.g. copper and zinc) and high iron content. The goal of the present work was to investigate extraction of base metals and gold from old flotation tailings containing 17% iron, 0.26% copper, 0.22% zinc, and 0.7 g/t gold. Chemical leaching in columns with 0.5 to 10% sulfuric acid solutions and bioleaching in air-lift percolators were used for the extraction of base metals. 1% H2SO4 provided high extraction of base metals and best selectivity. Recovery of copper and zinc reached 35% and 40%. Increasing H2SO4 concentration did not lead to significant increase in base metals extraction, but led to increased iron concentration in the pregnant solutions. The 1% H2SO4 leaching solid residues were used for further experiments. Acid leaching and bioleaching did not result in significant increase in base metals recovery. Leaching of the residue with 10% H2SO4 provided extraction of 4% copper and 20% zinc, and bioleaching for 100 days provided extraction of 16% copper and 12% zinc. The recovery of gold by cyanidation from the flotation tailings, the 1% H2SO4 leaching solid residue and residue of two-step acid leaching were 50, 49, and 65%, respectively. The results suggest that acid leaching can be effective approach for treatment of old flotation tailings.INTRODUCTIONAbout 80% of base metals (copper, nickel, zinc) are produced through pyrometallurgical treatment of sulfide ores. Mining and metallurgical treatments of sulfide ores are presently characterized by significant losses of non-ferrous and precious metals into the various wastes. For example, flotation of sulfidic ores yields formation sulfide flotation tailings. These wastes pose a problem not just because of their sheer volume, but some of them may affect local ecosystems. Nowadays, mining and metallurgical wastes can be considered as technogenical source of base metals."

Jan 1, 2016

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961