Search Documents

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By J. Paraszczak

For mining companies facing strong international competition and unfavourable commodities’ prices, automation of underground operations has the potential to increase productivity and help cut costs. However, despite considerable technological progress in this field, there still remain many problems to overcome. Furthermore, successful implementation of automation depends also on numerous operational, organizational, and even human factors. In this context, this paper briefly reviews technological progress with regard to different underground operations. Following that, several issues related to implementation of automated equipment and systems are presented and discussed. Particular emphasis is put on the factors whose importance is often underestimated. Some recommendations in this respect are also given. It is stated that the success of an automation project is a function of many “winning conditions,” which may be created through very thorough planning and preparation. It is also underlined that despite achievements made, a vision of a man-less underground mine is not yet as much a matter of near future as it may seem.

Jan 1, 2004

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

The ERMS Process was developed during four years of testwork by Austpac Gold NL to overcome the severe metallurgical problems of the ilmenite atWestport, in the South Island. These deposits have been known for about one hundred years. They were originally mined for gold, and only later attracted attention as a possible source of titanium minerals.   The resource is of world scale and may exceed 20 million tonnes of contained ilmenite. Similar deposits occur at Barrytown further south and together these areas would constitute an important opportunity for export-oriented mineral development, if a viable beneficiation technology were available. Further processing is essential, as the composition of the ilmenite is well below market specifications.

Jan 1, 1993

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

The first session of the Rocky Mountain Coal Mining Institute was called to order by John T. Maulsby, Superintendent of Maintenance and Planning, Columbia-Geneva Steel Division, U. S. Steel Corporation, Dragerton, Utah, representing the past-president. W. K. Dennison, Jr., Superintendent. Koehler line. Kaiser Steel Corporation. Raton, New Mexico, who was unable to attend. Mr. Maulsby welcomed the members and guests, and introduced the President, A. Z. Dimitroff, Mining Electrical Engineer, Health and Safety, District 1-L, U. S. Bureau of Mines. Denver. Colorado. The text of President Dimitroff's address of welcome is as follows: The President's Remarks Guests and Members of the Rocky Mountain Coal Mining Institute: The distinct honor and privilege of officially welcoming you to this, the fifty-seventh regular meeting of the Institute, is indeed a pleasure. Your officers and committees have tried to provide a varied program which I am sure should have something of interest to all of us. The theme of this meeting, "Where Do We Go From here'?", appeared rather fitting for the In¬stitute this year because, as most of you know, until only two weeks ago we thought that this is the last time we will be able to meet at the Colorado Hotel, which has been the favorite spot of most members. Your officers and many of you were literally asking just that question.

Jan 1, 1961

Study on Beneficiation Technology of a Refractory Fluorite Ore in North China

Sep 13, 2010

The introduction of computer technology to the mining industry has produced many benefits for the mining engineer. The most significant is the dramatic increase in productivity realized by the individual user. This is important during times of competitive market conditions. Software for the minerals and energy industries has evolved substantially over the past decade. But even today it remains difficult to find a system that features the flexibility and integration capabilities to effectively (and cost-effectively) handle the needs of professionals in each phase of the mining industry - from exploration to reclamation. Several national software developers are now addressing this challenge. One Denver-based company, MINEsoft Ltd., offers a software package that is currently being used in each phase of the mining industry. The basic technology used in MINEsoft's database management system was developed in the 1960s. But during these early years of the computer industry, most of the technology was available only on mainframe computers, and then only as separate entities. MINEsoft's system unifies these various systems in one package that can be used on most computers manufactured today. Database Management System TECHBASE is a flexible, integrated database management system designed specifically for technical applications. The system features a database manager with no practical limit to the amount of data it can store, retrieve, and manipulate, according to the company. TECHBASE in¬cludes Applications Packages (TAPs) designed to meet the needs of professionals in a host of industries. Clients use the TECH BASE system to prepare many reports, including important EPA information. The package reduces data to a manageable level and enables users to increase productivity with a smaller staff. Mining engineers no longer need to do things by hand. What used to be a day's work can be accomplished in an hour or two. Exploration "Using the TECHBASE system to generate maps has probably saved us the expense of three or four draftsmen," says Ralph Fitch, regional manager and senior staff geologist with Chevron Resources in Portland, ME. "The system has great flexibility. You can treat it much like a spreadsheet. If you are halfway through with a particular project, the system allows you to add fields and calculations with ease but without starting over." Fitch uses TECHBASE for the "straightforward" plotting of results and generation of geochemical and geophysical profiles. "In exploration," he says, "these are the two key elements ... the generation of maps and data profiles. The system allows you to plot as many elements and variables in these areas that you like." Other aspects are important, too, says Fitch, including drill hole sections. "We use all the basic capabilities the system provides in the complete package," he explains. "When shopping for a system, TECHBASE was clearly dedicated to exploration in the

Jan 9, 1987

L&M have been involved on the Shotover since 1980 when we joined Jack and Barney Ryan, who had started in 1972 with gold at $45 per ounce after a successful career as roading and demolition contractors in Christchurch. The first 85 tonne plant was a typical NZ trammel-riffle table plant with an armour plated hull for surviving Shotover floods, and was fed by a 53 tonne UH20 excavator. All this gear had to be carted in over the Skippers road on a small truck or sledge for the heavy loads. This operation was successful and generated the cash flow to sample the lower section of river and plan a second plant. To reduce fine gold losses this was planned to be a jig recovery plant and also included a vibrating screen which saved space and weight over a trammel. There are five flowlines of primary jigs and one secondary, followed by two Knudsen bowls for cleanup.

Jan 1, 1985

By B. S. Pierce

The National Coal Resource Assessment – 2000 project was a multi-year effort by the U.S. Geological Survey to identify, characterize, and assess the coal resources that will supply a major part of the Nation’s energy needs during the 21st century. The purpose of the USGS National Coal Resource Assessment (NCRA) was to (1) digitally assess selected coal beds and zones that will be the most important in the next few decades, (2) create publically available stratigraphic, geochemical, and geographic information system (GIS) databases to answer a variety of questions of importance to government, industry and public decision makers, and (3) provide interpretive geologic and geochemical information for the primary coal resources of the Nation. Five priority regions were assessed: the Appalachian Basin, Illinois Basin, Gulf Coast, Illinois Basin, and Northern Rocky Mountains and Great Plains. The NCRA was a cooperative effort between the USGS and a number of State geological surveys in these coal-bearing regions. A study of coal resources on Federal lands was also conducted. Adequate energy supplies and the efficient use of those supplies are critical to the economic well being of a country. Affordable and reliable coal supplies are essential to the interests of our national and local policymakers. Policy makers require a range of information on the energy supply, as well as the economic and environmental issues associated with that energy source and its use. Formulation of an effective national energy policy and development of energy resources requires that we understand the geology, distribution, quality, and size of the national energy endowment.

Jan 1, 2001

By T. G. Joseph, M. Bolster, M. Curley

"High tirerim loading on haul trucks operating on rough ground frequently manifests as mechanical separations and rim base cracking caused by cyclic fatigue. This paper provides an understanding of the impact of high loads on rim component life and tire footprint, bulge, and deformation behaviour; and develops a maintenance planning tool to predict strain implications of high g loading for a given rim location. Loading tests and analyses were conducted for a tirerim arrangement under increasing load and internal tire pressure. Graphical models were developed, allowing higher g load extrapolation predictions for specific rim components.KEYWORDS g load, Mining, Model, Prediction, Rim, Strain, Tire bulge, Tire footprint, Ultra-class vehicleRÉSUMÉ L’application d’un chargement élevé sur le système pneu/jante de camions de transport rou¬lant sur des terrains accidentés se manifeste fréquemment par des séparations mécaniques et une fissure à la base de la jante engendrée par une fatigue cyclique. Cet article nous permet de mieux comprendre l’incidence de l’application de charges élevées sur la durée de vie des composantes de la jante ainsi que sur l’empreinte, la hernie et le comportement de déformation des pneus. Il développe également un outil de planification de l’entretien visant à prévoir l’incidence des contraintes en cas d’application d’un chargement g élevé sur un endroit donné de la jante. Des essais et des analyses de la charge ont été effectués pour un agencement pneu/jante soumis à une charge et une pression interne du pneu croissantes. Des modèles graphiques ont été développés, ce qui a permis d’établir des prédictions sur la base d’une extrapolation du chargement g plus élevé appliqué à des composantes spécifiques de la jante.MOTS CLÉS charge g, contrainte, empreinte du pneu, exploitation minière, hernie du pneu, jante, modèle, prédiction, véhicule ultralourdINTRODUCTION The purpose of this paper is to report on a proposed and trialed tire performance test based on data obtained from controlled testing that is used to predict the impact of high g loading on hauler rims and tires with greater accuracy. For example, for many years oil sand mining operations have expressed qualitative beliefs that an impact load of the magnitude experienced by a rim and tire arrangement is not detrimental to a rim as a stiff component; however, mining equipment components are subjected to cyclic loading where failure can result from repeated load/unload activity, truncating the peak region of a stress–strain response and resulting in fatigue failure at a stress value that is less than the peak value. The outcome reported by oil sand haul truck maintenance groups indicates they have realized that most high g impacts—such as those experienced by hauler tires and rims operating on poor ground conditions—can result in failure due to cyclic loading, where higher loads require fewer cycles for failure. This high-level loading and the resulting strain transmitted to the rim is evident in the results of the laboratory testing presented in this paper."

Jan 1, 2019

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Blamey Stevens

(Butte Meeting, August, 1913.) THE following paper aims to make a full explanation of the phenomena of rock jointing: It may be unnecessary to give any general description of what are termed joints in rocks, but Professor Geikie's clear and faithful generalizations are so illuminating that no excuse need be given. for introducing the following and other quotations into this paper "Almost all rocks are traversed by vertical or highly inclined divisional planes termed joints. These have been regarded as due in some way to contraction during consolidation (fissures of retreat) ; and this is no doubt their origin in innumerable cases. But, on the other hand, their frequent regularity and persistence across materials of very varying texture suggest rather the effects of internal pressure and movement within the crust." 1 General Explanation.-In this paper I show that the phenomenon of jointing may to a large extent be accounted for by the pressure of the water contained in the pores of the rock. To understand this, each constituent grain of the porous material may be considered to be separately compressed by the water which submerges it. As all the grains are held together by cohesion, the whole mass is contracted by this pressure. In an indefinitely extended mass, however, there must be a limit to the possible contraction without rupture, because the material is restrained from moving freely by other material around its boundaries. The mass of rock thus becomes broken up. This phenomenon is known as '" shrinkage " jointing. The term " shrinkage " is an apt one, if it be understood that the shrinkage of the rock is often brought about by change of stress. Stresses.-The compressive component of water stress on the individual grains is evidently the same as that of the water with which it is in contact. This is so, both before and after the jointing is formed. Before the jointing is formed there is, however, a tensile stress in one or more directions which keeps the material from contracting. .

Jan 7, 1913

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By A. Sullivan

Success in mining demands the creative application of equipment, systems and processes to the unique needs of each mineral deposit, market and, though often overlooked, the culture of the individual business. In recent years, domestic coal mining companies have become more attentive to the contribution safety and loss control programs have on their financial results. Although most have adopted fairly conventional safety programs, some have created systems and processes tailored to their unique circumstances. While each coal mining business must consider the typical risks inherent to our industry, excellence in safety is most likely achieved when a safety program is customized to meet the needs of the individual business.

Jan 1, 2000

By H. D. Van Veldhuizen

The Multilateral Investment Guarantee Agency(MIGA) is part of the World Bank Group, and has as its mission the facilitation of foreign direct investment by providing political risk insurance (guarantees) to foreign investors and lenders. As a development institution, MIGA is required to ensure that the projects that it insures will bring development benefits to the host country. Demonstration of this includes review and analysis of the environmental and social soundness of a prospective investment. Environmental guidelines and policies developed by the World Bank Group are important components both in analyzing the environmental and social soundness of a prospective investment and in risk management. MIGA has recently formalized and adopted environmental assessment and disclosure policies. The approach taken by MIGA to environmental review of investments and implementation of these policies is described in this paper.

Jan 1, 2000