Search Documents

By Andrew Malinak, William Perkins

Seattle’s Elliott Bay Seawall protects the 1½ miles of downtown waterfront between South Washington and Broad streets. The seawall supports the urban waterfront and infrastructure, including the Alaskan Way Viaduct and Alaskan Way, access to historic waterfront piers, and numerous essential buried utilities. Most of the original seawall was constructed between 1916 and 1936 over soft/loose non-engineered fill, estuary, and beach deposits. The majority of the original seawall was a pile-supported timber relieving platform that extended up to 60 feet behind the face of the wall (Figure 1). With maximum spacing between the timber piles of 3 to 5 feet, a virtual forest of timber piles were driven for the original wall.

Jan 1, 2018

By L. C. Brown, C. St. John, C. C. Sanderson

The diffusion rate in Cu-Te couples is very sensitive to compressive stress, with a load of 20 psi making a significant difference to the width of the diffusion zone. At zero stress, two phases appear in the diffusion zone (Cu4Te3 and CuTe). Under compressive loading the third stable phase (Cuz Te) also appears, and its thickness increases progressively with increasing stress. The results are explained on the basis of an incipient Kirkendall porosity which restricts the transfer of atoms from the copper into the diffusion zone. DURING a study of the Kirkendall effect in Cu-Te couples prepared by clamping together the two components, it was found that the diffusion-zone width and shape in the plane of contact were not reproducible. Although the stresses involved in clamping are not normally sufficiently high to affect diffusion rates, preliminary tests established that the Cu-Te system is particularly stress-sensitive. The phase diagram for the system Cu-Te given in Hanssen1 shows that there is practically no solid solubility at either end of the phase diagram. Many areas of the diagram are not fully substantiated, but there appear to be three intermediate phases: Cu,Te—hexagonal in structure, having a grey luster; Cu4Te3—a tetragonal defect structure, having a red-purple luster; CuTe—orthorhombic in structure and having a golden-green luster. The existence of a fourth phase, the X phase at 37 at. pct Te, is considered doubtful. The composition ranges of the three stable phases are small, and are not accurately known. The phase diagram changes little with temperature up to 305°C, at which temperature a polymorphic transformation takes place in Cu2Te. The nature of the Cu-Te phase diagram indicates that the diffusion zone in a Cu-Te couple would consist of a series of layers of intermediate phases. The relative thickness of any one phase will depend on its diffusion coefficient and composition range.' In this type of diffusion couple it is often found experimentally that some phases are not visible at all in the diffusion zone due either to a small diffusion coefficient or to a restricted composition range.3 Since the composition ranges of the phases in Cu-Te are not known, it is not possible to determine diffusion coefficients in this system from a knowledge of the phase thicknesses. Several investigations have been carried out to determine the effect of compressive stress on diffusion rates in multiphase systems. Diffusion couples of Ni-A1 have been investigated by Storchheim et al.4 and by Castleman and Seigle.5 Two phases (ß and ?) appear in the diffusion zone under zero stress and the thickness of both phases is progressively reduced with increasing stress. According to Storchheim et al.4 a stress of 25,000 psi reduces the thickness of the diffusion zone by 50 pct. In a-brass—?-brass couples the thickness of the 0 phase formed in the diffusion zone was reduced by 20 pct at a stress of 20,000 psi.6 In other investigations the compressive load has been observed to increase the width of the diffusion zone. In A1-U, several investigators3,8 have found the width of the whase UA13 to increase with stress. According to casileman,8 the rate of formation of UA13 at 520°C is 75 pct faster at a stress of 20,000 psi as compared with a stress of 2500 psi. In Cu-Sb the effect of stress is greater than in the other systems described. According to Heumann9,10 only one phase (y) appears in the diffusion zone at a stress of 500 psi, but at a stress of 850 psi two phases (y and k) are present. If a diffusion couple containing both y and k phases is annealed at a low stress level, the y phase grows at the expense of the k phase. EXPERIMENTAL The diffusion couples were prepared from electrolytic copper bar stock with a nominal purity of 99.92 pct and from tellurium of 99.7 pct purity. The tellurium proved difficult to machine because of its brittleness and a technique was developed for casting the tellurium into a graphite slab mold and spark-machining specimens from this slab. Both the copper and tellurium were produced in the form of discs 2 in. diam by approximately 1/4 in. thick with surfaces ground flat to 3/0 emery paper. The diffusion apparatus is shown in Fig. 1. Auni-axial compressive stress was applied to the system through a simple lever system. A stainless-steel rod actuated by the lever arm lay inside a stainless-steel tube. The diffusion couple lay on top of the steel rod, and pressure was applied to the couple between the rod and a plug welded into the center of the tube. To ensure a uniform stress across the couple, a hemispherical boss and cup were used to transmit the load to the diffusion couple. A 400-w tube furnace with a uniform hot zone 3 in. long slid around the stainless-steel tube and maintained the assembly at temperature. A thermocouple situated 3 in. from the specimen operated a proportional temperature controller which maintained the specimen temperature constant to ±2°C. Most diffusion runs were carried out at 250C although a few tests were made at other temperatures in the range 235° to 300°C. The specimens were inserted and removed with the furnace at operating temperature, and took only 2 min to reach diffusion temperature—a time small compared with the total diffusion time. All the diffusion experiments were carried out in a hydrogen atmosphere, since consistent results were obtained in hydrogen and nitrogen atmospheres and in

Jan 1, 1967

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.' The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By Feng Cai

"As a new method to support gate roadways, rock bolting has been widely used in the big coal enterprises for its superiority. The disturbed stress field of surrounding rock and anchor pre-stress field were divided into 3 areas in consideration of s1, s3. The surrounding rock failure form and characteristic were analyzed in combination with parameter f, the failure mechanism was explained using the slip line theory, furthermore, the rock bolting mechanism and its arrangement were studied. After roadway excavation, the tensile stress area appeared at the surface of the surrounding rock. The failure type changes from shallow tension-shear form into deep compression-shear form and the failure shape is an “incense burner”, surrounding by high risk failure area in butterfly shape. The maximum principle stress in roof appears discontinuous distribution because of layers separation. The failure type of surrounding rock is intensity-stress environment-weak plane control model. The internal reason of roadway macroscopic failure is the displacement between the surface plastic area and the deep elastic region along the tangential direction of slip line. In condition of rock bolt support, there is one-way tensile stress area in small range at the surface of surrounding rock, inside is the bidirectional compressive zone in uniform distribution form, stress environment is improved by the superposition of anchor pre-stress and disturbed stress field, anchor rock bolt arrangement and pre-tightening force distribution is decided according to the distribution of f parameter. Finally, supporting method and parameter reasonability was proved by the roadway deformation monitoring, damage depth drilling peep test in the 8101 transportation roadway in a mine.Introduction The stability of roadway support is very important to the safety and sustainable development of coal mine. In recent years, the focus of China's coal mining industry began to move to West China, the thick-extra thick coal seam is developed in the West. The latest technology and equipment have been put in to service, the occurrence condition of thick coal seam and the increasing of productivity lead to the cross section of the roadway increasing continually, hence, it is more difficult to control the surrounding rock. At present, the most common way to support the roadway is rock bolt (cable) support (Wang 2007); Scholars have been deeply studied on the mechanism of rock bolt. It is reported (Wang et al 2012, Gao 2007, Zhang and Yuan 2006) that the influence of rock bolt on physical and mechanical parameters of coal and rock mass in the anchorage zone, It is believed that the rock bolt can improve the peak strength of surrounding rock, especially the post peak strength, and the failure mode of rock mass under the rock bolt support is analyzed. It is reported (Wang et al 2014, Xiao et al 2013, Li et al 2007, Yan et al 2012), according to different geological conditions, the failure mechanism of surrounding rock and supporting technology of the whole coal roadway were studied. Focus on the failure mechanism of roadway surrounding rock, different forms of high strength support methods were proposed, which achieved good results. It is reported (Wang et al 2012a, Zhang et al 2011, Wang et al 2012b, Kang et al 2010, Zhang et al 2010, Kang et al 2007) that the supporting mechanism of pre-stressed anchor was analyzed from the point of the distribution of the maximum principal stress in the pre-stressed anchor field, and the influence of the rock bolt support parameters and surrounding rock characteristics on the supporting effects were studied. Based on the latest research results, this paper analyzed the failure mechanism of surrounding rock of coal roadway, proposed the high strength anchor net cable combined supporting technology based on the feature of stress zoning distribution of surrounding rock, to provide reference for the coal roadway rock bolt (cable) support technology."

Jan 1, 2017

By C. C. Walden, A. Bruynesteyn

"Chemical and biological aspects of the formation of acidic effluents from sulfide waste materials are discussed. Test procedures to determine the acid producing potential of waste materials, as well as the characteristics of such acidic effluents, are presented. Practical applications of the test procedures are discussed with reference to predictior of environmentally unacceptable drainage and to estimation of metal recovery by dump leaching.INTRODUCTIONNatural leaching of sulfide minerals, exposed to the atmosphere, has been occurring for geological time. For centuries, man has been aware of the acid drainage originating from coal workings, copper mines and waste dumps. With the advent of the technical sciences, the processes involved in acid mine drainage production were considered to be solely chemical in nature. However, in 1947, it was shown (1) that a specific microorganism, called Thiobacillus ferrooxidans, was responsible for acid mine drainage from coal workings. It was demonstrated that under suitable conditions - this bacterium oxidized pyrite and marcosite in the coal to ferric sulfate and sulfuric acid. Numerous studies have subsequently demonstrated that - under suitable conditions - Thiobacillus ferrooxidans can attack most sulfide minerals, producing weak sulfuric acid, oxidizing ferrous to ferric iron and solubilizing other metals present (notably copper and zinc) as their sulfate salts."

Jan 1, 1980

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By R G. Barker

This paper reviews the annual status of the New Zealand mining industry (metallic minerals and coal) including key aspects such as mineral production, mineral exploration expenditure, commodity price trends, key industry players, market activity and other significant commercial factors.   Strong commodity prices during 2006 have been underpinned by a number of key factors including US dollar weakness and emerging market demand, particularly from countries such as China and India. In real terms commodity prices have recovered significantly since 2002 and are currently at 20-year highs.   New Zealand exploration spending on metallic minerals (predominantly gold) is at a 15 year high driven by rising global commodity prices. New Zealand gold production in 2006 was about 340,000 oz and is expected to grow in 2007 as new mines at Frasers and Globe-Progress (Oceania Gold) and Favona (Newmont) come on stream. Gold production broadly lags 10 years behind exploration spending and exploration activity over the last five years remains well below that seen in the early 1980Æs. Expenditure on coal exploration shows a similar trend with strong growth from a low base over the last five years, reaching over $11 M in 2006. Total coal production in 2006 was 5.9 Mt, an increase of 10% on 2005 with imports from Indonesia adding a further $1.1 Mt.   Newmont and Oceana Gold are by far the largest public gold mining companies operating in New Zealand, although only Oceana Gold maintains a presence on the local stock exchange. Other metals explorers with New Zealand projects include a range of public-listed Juniors (market capitalisation less than NZ$50m) domiciled largely in New Zealand, Australia and/or Canada. Capital-raising on public markets directed towards New Zealand exploration is estimated at around NZ$12 M for 2006, the bulk of this coming via Glass EarthÆs NZ$10 M IPO on the NZAX in October.   The New Zealand Coal sector is dominated by the state-owned enterprise Solid Energy with around 80% market share by production. Other domestic coal competition remains limited, and includes the L&M Group, Pike River Coal, Eastern Corporation, and New Vale (acquired by Solid Energy in 2007). Pricing parity comes mainly from imported coal and global thermal coal prices have remained strong during 2006 at around US$45-55/t, driven by continued expansion in Chinese demand. Coking coal prices have eased 16% since 2005 to around US$98/t in 2007.   Although recent increases in exploration spending suggest a renaissance in the New Zealand minerals sector, long-run trends indicate that we have simply rebounded from a low base over the last five years and much work is still to be done to stimulate further growth in the mining industry to maintain minerals production at current levels. Key industry challenges include marketing exploration opportunities to local and overseas investors, building a critical mass of NZX-listed explorers and providing an internationally competitive environment to attract further capital and expertise.

Jan 1, 2007

By M. K. Larson, J. K. Whyatt, R. B. Langston, J. C. Johnson, H. Kirsten, T. M. Brady

An experiment is described in which hollow inclusion cells (HICells) were used to measure stress in a jointed rock mass during drift development at the Stillwater Mine, Nye, MT, USA. Two HICells were installed in the footwall approximately two drift widths ahead of the face. One HICell was over cored and then immediately tested in a biaxial chamber. The other HICell was left in place and monitored as the drift was excavated in three advances, each one-half the width of the drift. Strains were recorded hourly by a datalogger. Results show that there was little stress change during the first and second drift advances, but that a large stress change occurred after the third advance. The measurements also showed that the in situ principal stress directions lined up with regional geologic structures. Stress changes during face advance were likely caused by deformation along localized joint sets and inelastic deformation near the face.

Today?s Topics ? Data to decision value chain ? Practical Considerations ? Example ? Before / After DSS ? Quick Decision Support Demo Practical Considerations ? More data is not necessarily better ? Organization and process silos ? Good vs. ?optimal?, but impractical Solutions

May 1, 2008

By L. K. Smith

The position of Australia as a continuing long-term supplier of mineral sands, and their upgraded products, has been reinforced with the discovery of the extensive mineral reserves in the Murray Basin, an area covering parts of South Australia, New South Wales and Victoria. A major impurity in the Murray Basin is chromium, mainly present in ilmenite concentrates as individual chrome spinel grains. Magnetizing roast treatments are being evaluated as a means of removing the chrome spinel impurity from the ilmenite and as a result of the roast and magnetic separation treatments, the chrome spinels can be expected to be concentrated in the non-magnetic reject fractions. It is from these fractions that attempts were made in this study to recover a chromium-rich product by magnetic fractionation and by application of flotation. The high gauss non-magnetic rejects from the roasting of a primary and a secondary ilmenite fraction were magnetically fractionated to obtain a product with 40.5 and 28.7 per cent Cr2O3,respectively. From the high gauss non-magnetic reject from the roasting of a primary ilmenite, flotation produced a chromium-rich product assaying 29.5 wt per cent Cr2O3at 69.0 per cent recovery. In another test a magnetic fraction assaying 32.9 wt per cent Cr2O3was floated to yield a chromium-rich product with 39.7 wt per cent Cr2O3at 96.4 per cent recovery. X-ray diffraction patterns of all the products indicated that the spinel concentrated was a ferroan magnesiochromite with rutile, ilmenite and hematite as impurities. Since all products were from a single pass, further processing can be expected to remove the impurity minerals and yield higher grade products. The material produced from the Murray Basin ilmenites in this study had similar compositions to commercial chromite ores, except for titania levels that were much higher. The high titania levels were due to residual rutile in the products, but it is expected that this can be removed with further processing. The mineral sand deposits in the Murray Basin are scattered over a wide area and the amount of chromite that may be produced from each of these deposits is unlikely to be sufficient to support an export market. Consequently, any chromite produced in the Murray Basin will most likely need to be processed locally to value added products for a niche market such as chemicals production. Keywords: Murray Basin, ilmenite, chrome spinel, roasting, magnetic separation, chromite ore

Jan 1, 2003

Jan 1, 1967

By Wenbing Guo

The stability of strip pillar is the key to successful strip pillar mining. In analyzing the stability of the strip pillar, the width of yield zone must be determined. The determination of the width of yield zone has been an important subject for researchers. In this paper, the numerical method was used to study the relationship between the width of yield zone in strip pillar and coal recovery ratio. The results showed that as the recovery ratio increases, the width of yield zone increases exponentially. Accordingly, the formula for determining the width of yield zone was updated and the effect of changing coal recovery ratio on strip pillar deformation is presented.

Jan 1, 2006

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located above the Arctic Circle in northern Sweden, is the second-largest underground mine in the world today. The orebody is a world-class high-grade magnetite deposit, from which three raw ore products are extracted. We use mixed integer programming to determine a production schedule, i.e., which production blocks to mine, and when to start mining them, so as to minimize deviation from planned production quantities while adhering to the operational constraints of the mine. The resulting model contains thousands of binary variables and a commensurate number of constraints, precluding us from obtaining a schedule in a reasonable amount of time. We describe a method that builds on prior, related work, to expedite solution time. Keywords: underground mining, production planning, optimization, integer programming

Jan 1, 2003

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986

By E. M. Abraham

The establishment and survival of different grass species and cultivars on various phytotechnic treatments at a limestone quarry was studied. The treatments applied were: a) bare soil, b) bentonite, c) bentonite-straw and d) asphalt-straw. According to the results, significant differences were found among species and cultivars, growing on different treatments as far as plant growth and survival are concerned. The seed germination was higher on bentonite -straw and asphaltic-straw than on bentonite but the plants survival were higher on bentonite. Lolium perenne had higher seed germination rate and better establishment than the other tested species at all treatments. However, the survival rate of Agropyron desertorum and of the cultivars palestina and chrysopigi of Dactylis glomerata was higher than of the other species.

Jan 1, 2007

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By B. Ladanyi, B. Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a propw knowledge of the distribution of stresses within the slope and their development with time and advancement of workings. There are a uumber of different methods that can be used, in principle, for obtaining this information, such as (1) stress measurement in situ, (2) photoelasticity,1 (3) analytical methods, and (4) numerical methods. In cases where the stress distribution cannot be obtained by classical analytical methods, as in the one considered herein, either photoelasticity or numerical methods are norrnally used. However, actually, due to the rapid development of high-speed computers, increasing preference is given to the numerical methods. Among the latter, the most successful ones, to date, for determining the stress distribution in slopes have been (1) the finite difference method,2-4 (2) the lumped parameter method,5 and (3) the finite element rnethod.6 However, for determining gravity stresses in a natural rock slope, only the finite difference method has been used until now.7,8 A solution of the same problem by the finite element method will be shown here in which a particular reference is given to the development of tensile fracture zones within the slope. FINITE ELEMENT METHOD The stress analysis using the finite element method originates from an extension of the matrix analysis of structures.9 It consists in decomposing a continuous medium, assumed herein to be homogeneous and isotropic,

Jan 1, 1972