Search Documents

By Eung Ha Cho, Wendi Li

Wet desulfurization of Pittsburgh No. 8 coal and Illinois No. 6 coal were conducted with sodium hypochlorite in the laboratory. Pittsburgh No. 8 coal was leached by hypochlorite at high pHs in one step only. The hypochlorite concentration varied from 0.2 to 0.6 molar; sodium hydroxide concentration, from 0.2 to 0.8 molar; and temperature was at the levels of 80 and 90°C. The desulfurization of Illinois No. 6 coal was conducted in three consecutive steps of pretreatment in concentrated ammonia at room temperature, leaching with hypochlorite at room temperature and hydrolysis in sodium hydroxide solution at 90°C. In the leaching step, hypochlorite concentration varied from 0.2 to 0.8 molar. The desulfurization method of Pittsburgh No. 8 coal was found to reduce mainly pyritic sulfur. More than 70% of pyritic sulfur removal was achieved at the optimum conditions of 0.4 molar hypochlorite, 0.4 molar sodium hydroxide and 90°C. The desulfurization method for Illinois No. 6 coal was capable of reducing significant amounts of organic sulfur. The removal of organic sulfur achieved a 37.8% reduction at the optimum operation of leaching at 0.4 molar hypochlorite and room temperature followed by hydrolysis at 0.3 molar sodium hydroxide and 90°C. The chlorine content in the coal produced by the chlorination during leaching was kept below the threshold value of 0.3% at the optimum conditions of the desulfurization method for each coal.

Jan 1, 2005

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36, and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

Feb 27, 2013

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Experiments were conducted to study the influence of temperature, particle size and ore/coke ratio on the kinetics of reduction. The rate of reduction increased with temperature. The reduction of iron was completed at shorter time intervals at temperature above 1000ºC. Usually the reduction of chromium commenced after the reduction of iron was almost complete. Reduction was controlled by diffusion at low temperatures and by chemical reaction at higher temperatures. The nature of the reducing agent had a very significant influence on the rate of reduction. The study showed that chromium was converted into the carbide during reduction. Increasing the size of the reducing agent increased the rate of reduction initially. After a critical size, the rate of reduction decreased. However, increasing the size of the ore particle decreased the rate of reduction, initially. Beyond a critical size, it increased. An optimum particle size of the chromite ore and that of coke must be chosen, particularly in the production of agglomerates to achieve maximum degree of reduction.

Jan 1, 2007

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

By E. D. Gardner

FIFTY years ago the Utah Copper enterprise at Bingham was just getting under way. An epic in metal mining was in the making. Throughout the West the bonanza deposits were approaching exhaustion and most ore still went direct to smelter. But concentrators were shortly to be constructed for treating milling grade ores, and most important, the pilot plant for the Utah Copper enterprise was being built that year at the mouth of Bingham Canyon. The same decade was to see development at the Inspiration mine in Arizona of the most important new mining method for 50 years to come—undercut block caving. Although the average grade of ore being mined has been declining for 50 years, and wage rates and prices of supplies have been greatly increased, the mining industry has continued to grow and to prosper. Technology has advanced to a point where minerals can be mined under the most severe conditions. The hardest rock can be drilled and broken and the heaviest ground handled. Large or small, an ore-body can be mined successfully, at any desired rate of production. It is possible to pump great volumes of water and to ventilate the most extensive workings; air conditioning has made practicable the mining of ore where the rock temperatures are beyond those that can be borne by man. Mining today in the U. S. is a huge earth-moving operation. In 1953 nearly 2 billion tons of material were mined for direct use or for processing. Stripping at open-cut mines totaled about 1.7 billion cu yd. Table I gives relative tonnages of the branches of the mineral industry in 1953. In addition to the solid materials moved, 350 million tons of petroleum and 340,000 tons of gas were produced in 1953. Fifteen million tons of salt and 5 million tons of liquid sulphur were pumped from wells. An appreciable amount of copper was recovered by leaching old mine workings and dumps. Total value of minerals produced in 1953 was $14.4 billion: oil and gas $7.6 billion, coal $2.6 billion, nonmetallics $2.4 billion, and metals $1.8 billion. Formidable problems face some branches of the industry today, especially pertaining to increased output tons per manshift. The time has come when these problems should be reappraised. With current wage rates, the industry no longer can afford to pay men to do manual labor. It should be recognized, also, that the miner is a skilled worker; efforts to promote the dignity of his calling and his pride of accomplishment have yielded beneficial results. Mineral deposits occur under widely varying conditions. In most instances the degree of support needed by the roof and walls is the deciding factor in selection of an underground mining method. The degree of support needed, in turn, is governed by natural physical characteristics of the ore and its enclosing rocks. Mine operators, of course, learn to judge ground by observation, and an experienced mine boss generally can anticipate what will happen following any given mining operation. A more scientific approach, however, would be advantageous in most cases. More should be known about the strength of the ore and the enclosing rocks, more about stresses set up in the ground when ore is removed, and more about the mechanics of moving ground. Better understanding would work both ways: first, favorable rock conditions could be fully utilized for more efficient mining, and second, hazards of rock falls could be minimized, loss of ore in mining reduced, and expenses caused by ground pressures and subsidence lowered. In general, mining comprises breaking the ore or rock in place, supporting the mine workings, and transporting the ore to the surface. This latter is a materials handling problem. Ventilation, of course, must be provided, and the mines must be kept free of water. Development work at some places is the most important cost item in extracting ore. Drilling and blasting remain the usual practice for breaking ore or rock from place except, of course, at block-caving mines. The drilling and blasting practice at a mine must fit the mining method. In laying out mining procedures attention is being given to

Jan 1, 1956

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Xiong Dahe

In recent years many creative technologies are applied to SLon vertical ring and pulsating high gradient magnetic separators. SLon-2500 and SLon-3000 vertical ring and pulsating high gradient magnetic separators are created towards larger scale. Through optimizing the magnetic system and lowering the electric current density, their energy consumption is obviously dropped. New magnetic matrixes are developed to raise the beneficial efficiency of valuable minerals. Special SLon vertical ring and pulsating high gradient magnetic separators are developed which can treat coarser particles of 0-5 mm. Through these technology creations, the mineral processing efficiency of SLon magnetic separators is further raised and their processing cost dropped. Therefore, they have been found wider applications. SLon-2500 applied in Essar Steel of India. In 2007, Essar Steel did a test on its Kirandul hematite ore with SLon magnetic separator and got very good results. The feed grade is 59.77%Fe, after SLon one roughing and one scavenging, the total iron concentrate grade is 65.00%Fe and iron recovery 93.86%. In 2008-2010, the company bought 10 SLon-2500 magnetic separators to treat such iron ores. In 2010 the first SLon-3000 was applied to processing ilmenite. The magnetite-ilmenite deposit is located in Pan Zhi Hua, Si Chuan Province of China. The ore processing flow sheet is: Drum low intensity magnetic separator is used to take out magnetite, and then the SLon-3000 is used to recover ilmenite for roughing. The mags of the SLon-3000 are further cleaned by flotation. The SLon-3000 average operational results are: feed grade 9.52%TiO2, mags grade 17.43%TiO2, mags mass ratio 41.01%, TiO2 recovery 75.09%, non-mags grade 4.02% TiO2, non-mags mass ratio 58.99%. SLon magnetic separators Applied to treat 0-5mm limonite: The feed of SLon magnetic separator is usually 0-2 mm which needs to be ground by ball mill. As many Chinese iron ores are poor grades, if we can throw part of tails before grinding, the grinding cost will be greatly reduced. In 2010, a SLon-1500 and a SLon-2000 were specially built to treat 0-5 mm limonite. The feed grade is 26.51%Fe, mags grade 53.20%Fe, iron recovery 64.26, and tails grade 13.66% Fe. SLon-2500 applied to purify quartz. In 2009, a SLon-2500 magnetic separator was applied to purify quartz in Shan Xi province. Its feed is 0-1mm quartz which contains 0.15%-0.25%Fe2O3, the designed non-mags grade need to be less 0.08% Fe2O3. The production results of SLon-2500 non-mags are 0.05-0.06% Fe2O3, much better than the designed data. SLon applied in Si Jia Ying Iron Mine to recover hematite. Si Jia Ying is a big oxidized iron mine located in He Bei Province of China. In 2005-2010, a plant annually treating 10 million tons of oxidized iron ore was built in which 39 SLon magnetic separators are applied. The total flow sheet results are: Feed grade 30.44%Fe, iron concentrate grade 66%Fe, iron recovery 80%Fe, tails grade 9.65Fe%. SLon applied to recover specularite. Li Lou Iron Mine in An Hui Province of China built a plant annually processing 5 million tons of iron ore in 2010-2011. 25 SLon-2000 magnetic separators are applied to recover specularite. The total flow sheet results are: Feed grade 31.65%Fe, iron concentrate grade 65%Fe, iron recovery 80%Fe, tails grade 10.37%Fe. SLon applied in Da Hong Shan Iron Mine. Da Hong Shan Iron Mine is located in Yun Nan province of China. It treats 4.5 million tons of oxidized iron ore annually. 15 SLon-2000 magnetic separators are applied to recover hematite. The total flow sheet results are: Feed grade 35.61%Fe, iron concentrate grade 64.95%Fe, iron recovery 74.08%Fe, tails grade 15.55%. Keywords: SLon magnetic separator, iron ore, ilmenite, quartz, beneficiation

Sep 1, 2012

By E Ben-Awuah

Mine planning is the backbone of all mining enterprises and determines the profitability or otherwise of any mining investment. Providing high quality ore and tailings containment at the right time are the main drivers in oil sands mining. Recent environmental and regulatory requirements also makes waste management an integral part of mine planning in the oil sands industry (Directive 074). Due to the limitation of lease area, the pit phase advancement in oil sands mining is carried out simultaneously with the construction of tailings dykes in the mined out areas of the pit. These in-pit dykes are constructed to hold tailings that are produced during the processing of the oil sands ore after an initial external tailings facility. Most of the materials used in constructing these in-pit and ex-pit dykes come from the oil sands mining operation, making it necessary to have a plan for supplying the dyke material. The research problem here is categorised as: determining the order of extraction of ore, dyke material and waste to be removed from a predefined ultimate pit limit over the mine life that maximises the net present value of the operation û a strategic schedule; anddetermining the destination of dyke material that minimises construction cost depending on the construction requirements of the various dykes as per their designs û an operational schedule. There has been developed, implemented and verified a theoretical optimisation framework based on mixed integer goal programming (MIGP) to address the oil sands long-term production scheduling and waste management problem. The research introduced the development of multiple material types and multiple destination optimisation techniques using MIGP in the context of mine planning. This study presents an integration of mixed integer programming and goal programming in solving large-scale mine planning optimisation problems using clustering and pushback techniques.

Sep 26, 2011

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

To reduce the exposure of mining machine operators to respirable dust. Approach: A protective curtain of filtered air is blown down around the operator's head, from a manifold mounted on the machine canopy. How It Works: Mine air is drawn into the system through a filter which removes respirable dust. The filtered air enters a centrifugal blower which pushes it through a flexible hose to a manifold mounted on the canopy above the operator. Air leaves the manifold through a perforated plate and flows down around the operator's head. A photograph of an installed system can be seen in Figure 1. The second photograph, Figure 2, shows the sys-tem components. An important advantage of this dust protection system is that it is not worn or carried, or in any way connected to the operator. It is therefore not uncomfortable, encumbering, or

Jan 1, 1976

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

By R. P. H. Willis

For technology transfer to be successful a process, from research to full scale application, has to be followed. This paper describes such a process and how it is applied in practice. Some of the ?do?s? and ?don?ts? are highlighted. Recommendations are made on how to communicate existing knowledge and to ensure that a framework exists to effectively plan future projects with final technology transfer objectives firmly in place. The Impact Ripper System is used as a case study to illustrate lessons learned. Key words: Technology transfer, implementation

Jan 1, 2002

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 239 to 245. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropriateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at30th June, 1997, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1997

By A. M. Bell

"Hallnor mine is in the township of Whitney, Porcupine district. To date, its production of gold has been second largest in the east Porcupine field. Ore was discovered in the property in 1936 by diamond drilling in overburdened country. This drilling was undertaken by Noranda Mines following the discovery of ore in conglomerate at Pamour 1 mile to the east.Milling commenced at the Hallnor in June 1938, and to the end of 1945 432,000 oz. gold had been produced from 889,000 tons of ore, giving an average recovery of 0.49 oz. a ton.The West mine of Pamour, the Broulan orebody, and the veins on the Hallnor and Bonetal are all parts of a mile long vein system that has been separated into three sections by cross faulting. In consequence, they could well have been described in one paper. In treating them individually the viewpoint obtained from each may lead to conflicting opinions, and any conclusions advanced in this paper on the general structure should be modified by the conclusions advanced in papers on the neighbouring properties.GENERAL GEOLOGYRock FormationsThe Hallnor orebodies occur within 400 feet of the contact between lavas and sediments, and may lie in either lavas or sediments. The lavas near the ore consist of flows of pillowed andesite and one flow of more acid and less sheared and chloritized lava locally named trachyte. These flows strike east-west and dip steeply. At the surface on the east side of the property the volcanics have been intensely altered to a massive carbonate rock having a north-south thickness in excess of 1,000 feet . This carbonate body extends west across the property with a plunge of 45° (Fig. 1)."

Jan 1, 1954

By Richard Jundis

At the Vale Inco Ontario Operations, the working environment is rapidly evolving with organizational changes, new business systems and software tools. These changes are required in order to meet today?s challenging business environment. Mining professionals are focusing on the development of safe and achievable mine plans to maximize mining value while reducing the potential of project delays and production shortfalls. This paper explores how new design tools, techniques and system designs in mine planning are being developed to optimize the value of every ton of ore mined and processed. To differentiate from other papers on long-term planning, this paper focuses on the concept of business planning at the mines. Business planning is the understanding and optimization of the relationship between mine plans and the value it adds in the overall process. The management and key stakeholders of Vale Inco have recognized that the development of a robust mine planning system and programs are essential for the long-term sustainability of the operations.

May 1, 2009

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001