Search Documents

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland.   Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz.   Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this.   Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006

By E. De Souza

Two comprehensive surveys, which focus upon backfill practices and the economics of backfilling in underground mines in Canada, have been conducted. The two surveys were designed to assess operational practices and costs associated with the wide scope of filling operations that must be met by individual mines, ranging from raw material feed to the preparation plant, through underground backfill transportation, to in-stope product placement. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database of information upon which they might compare their own practices and costs with present trends throughout the industry.

May 1, 2003

Gold mining in Australia and globally has a long and variable history. In recent years, due to ongoing public concern over long-term environmental impacts, the mining industry globally has been moving towards a more sustainable framework, presented as the æMining, Minerals and Sustainable DevelopmentÆ (MMSD) framework at the Johannesburg Earth Summit in 2002. There are a number of fundamental issues and concerns with assessing the sustainability of mining. Firstly, long-term trends show that ore grades for almost all metals and minerals will continue to decline (some rapidly so), increasing waste rock is being produced due to the trend towards large-scale open cut mining and more complex ores are now commonly being developed. The impact of these trends on the resource intensity, or unit cost, of gold production is of major concern as it could lead to an increase in energy, water and reagent consumption and greenhouse emissions per unit gold produced. A detailed compilation of these fundamental sustainability indices for gold mining has been undertaken, and is presented with respect to indices over time, ore grade and ore throughput. A clear observation is that the resource intensity of gold mining is extremely sensitive to the ore grade, with energy, water and cyanide consumption and greenhouse emissions rising significantly as ore grade decreases. Based on the gold ore resources at operating mines and other known gold deposits, it is most likely that the average gold ore grade will continue to decline, leading to increased resource intensity and consequent environmental impacts (assuming no breakthrough new technologies occur). These findings are of major importance to understanding the sustainability of gold mining. The final judgement of the sustainability of gold mining therefore must take into account the sensitivity of the ore grade in the resource intensity of gold production.

Jan 1, 2007

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

In practice, frothers are selected following general guidenlies and verification by laboratory and/or plant flotation tests. The terms “powerful” or “selective,” which are commonly used to characetrize frothers, have intuitive rather than scientific meaning. A research program has been set out to study fundamental properties of the flotation frothers and to identify the tests which can provide information needed to characterize and classify such flotation agents.

Jan 1, 2004

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

By J. A. King, D. A. Knight

"The Porgera orebody is located in mountainous terrain in Enga Province, Papua New Guinea. An underground mine has been developed which produces up to 2000 t/d of ore grading over 2 ozs Au/t. Some 79% of the gold in the ore is free, with the balance in a highly refractory form as sub-microscopic gold evenly disseminated within a pyrite matrix.This paper describes the metallurgical plant that uses flotation and cyanidation circuits to effectively recover the free gold in the ore feed, allowing for wide variation in the gold head grade. The refractory gold component in the ore is stored as leached pyrite flotation concentrate and this concentrate will be later treated by autoclaving techniques to recover the contained gold.The ProiectThe property is located in the Porgera Valley 600 Km North West of Port Moresby. The remote location is 2500 m above sea level. The mine area has 3600 mm of annual rainfall and a temperate climate with temperatures ranging from 10° c to 22° c throughout the year.Alluvial gold was reported in the Porgera area in 1938 and has been an important source of revenue for the area for many years. Intermittent exploration was carried out until the 1960 1 s when Placer (PNG) Pty. Ltd. with Mt. Isa Mines commenced an extensive exploration program. The property was brought to production in 1990 by the Porgera Joint Venture group consisting of Mount Isa Mines Ltd, Rennison Goldfield Consolidated Ltd. and Placer Dome Inc, each with a 30% ownership and the Government of Papua New Guinea with a 10% share. Placer Dome Inc. is the manager of the property with construction under the direction of the Placer Dome Technical Services group."

Jan 1, 1992

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

Jan 1, 2004

By D. M. Doyle

"A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc. over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study 11rogresses through monthly, daily and finally, into quarter hourly data, the variations become more evident and most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program.The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Sudbury Operations, the material and control equipment, the commitment, the new energy accounting practices and lastly, the policies. Examples of successful energy conservation endeavors include automatic peal electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailmen: of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and if necessary, immediate reporting of energy and energy per unit of production information. The program so reported at Falconbridge’s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0 million dollar annual energy account."

Jan 1, 1979

Frothing in Seawater Flotation Systems

Sep 13, 2010

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

By F. Díaz-Fierros, D. Rubinos, M. T. Barral

The present work explores the reutilization of red mud, an industrial waste arising from the production of alumina, as a component of isolation technologies for hazardous substances. The work involved the study and optimisation of the geotechnical properties of red mud in conjunction with adsorption experiments of As(V) and Hg(II). The results from both types of experiments were integrated in a dispersion-diffusion model to calculate migration curves and minimum thickness of the red mud compacted layer. The geotechnical studies showed that compaction increased the stability and decreased the hydraulic conductivity of red mud barrier. Red mud sorbed high amounts of As (up to 44 mmmol kg-1) and Hg (up to 9.2 mmmol kg-1). The calculated minimum thickness of the red mud barrier was 1-10 cm for As and 2-19 cm for Hg, for an operation period of 35 years. The results obtained let to conclude that the reuse of red mud as a component of isolation systems of hazardous substances represents a viable alternative use of this residue.

Jan 1, 2011

One of the most important parameters in mine ventilation planning is the friction factor (K). Accurate values of friction factors are critical especially when carrying out mine ventilation simulations. No computer simulation of a mine ventilation network is meaningful if the airway resistances are not accurately estimated (when planning a new mine) or measured (for an existing mine). However, in the first case not many reliable values of friction factors exist in the international literature. This paper presents the results of a research project carried out in the province of Quebec where ventilation friction factors were measured in all underground metal mines. These friction factors are statistically analyzed and tabulated. A friction factor database was created that also includes the friction factors measured in the past by other people. This database can help the mine engineer to accurately estimate ventilation friction factors according to the specific conditions. This database offers several values of friction factors typical for hard rock mine conditions typical of modern underground metal mines.

Jan 1, 2009

By G. R. Mansfield

THE geologic structure of the Idaho phosphate field has an important bearing on the classifica-tion and the exploitation of the lands that contain phosphate. Maps and structure sections1 recently made available show that the phosphate is mainly preserved in downfolded or downfaulted areas. Since the phos- phate beds are generally rather soft and lie between harder and thicker formations they have been forced to adjust themselves to these formations during epochs of disturbance of the earth's crust, so that they are frequently affected by minor folds and by faults which may help exploitation by producing undue thickness at certain places or may hinder it by cutting out the phosphate at other places where according to expecta-tion it should be present. A particularly important structural feature which affects both the distribution and the exploitation of the phosphate beds is the great Bannock overthrust by which one or more slices or blocks of the earth's crust have been pushed over other blocks like ice cakes on a pond. Thus in this region a great flap of folded rocks lies across other rock structures for a distance of approximately 35 miles. Most of the commercially accessible phosphate deposits, shown in the maps that accompany the report cited, are in this flap, which con-stitutes the upper block of the overthrust. In some places, however, the phosphate in the lower block is also accessible. In both blocks post-phosphate rocks exposed at the surface here and there indicate that phos-phate beds may lie at greater or less depth below. The presence of the Bannock overthrust beneath much of the area reported is known by the occurrence of windows in the upper block both within the quadrangles mapped and in areas farther west. The portions of the lower block exposed in these windows show stratigraphic dis-cordance with the surrounding formations. The depth of the fault plane at most places, however, can be told only by drilling or actual mining. Some of the folds in the upper block are relatively deep and it seems fairly certain that the phosphate that may originally have been present in their deeper parts has been removed by thrust faulting. The estimates of phosphate reserves in folds liable to be affected by the Bannock overthrust may therefore need ultimate revision depending on the depth of this fault plane, as it may subsequently be ascertained.

Jan 1, 1928

By Mohammad Irshad, Klaus Mussger, Harald Wagner

Despite the fact that the New Austrian Tunneling Method; NATM, has been used in the United States for the past 23 years or so, still considerable misconceptions exist in the industry about the nature of the method and its implementation. In the authors’ view its implications are usually not well understood. The paper provides an overview of the highlights of NATM usage over the past two decades to illustrate the point that NATM is now a well-established tunneling method in the U.S.A. Accordingly the thrust of this paper is on the more pragmatic aspects of the NATM technology usage as it concerns the Owners, Designers and the Contractors. Prior to examining the implications of NATM usage from the viewpoints of various stakeholders, it should be helpful to first briefly provide an overview of the history of the method as it was introduced and implemented on several key tunneling projects in the US, over the last 2 plus decades.

Jan 1, 2005