Search Documents

By R. Butcher

Mud rushes are hazardous occurrences that have occurred frequently in mines in South Africa, and have been the cause of numerous fatalities in the past. Mud rush incidents not associated with accidents are believed to be common occurrences that are not generally reported. Many such incidents are probably associated with the operation of chutes and box fronts. This paper describes the conditions necessary for mud rush occurrences, postulated mud rush mechanisms, and methods of combating the mud rush hazard.

Jan 1, 2005

By D. A. Bruce

The paper describes the construction of 5 plugs to resist high water heads at depth within the South Deep Gold Mine, Randfontein, South Africa. A total of 20 segments were involved to create these plugs, which were 7.5 m long at the 58 Level and 6.25 m long at the50 Level. Emphasis is placed on the QA/QC and verification methods, which were developed and governed all phases of the work, from initial rock preparation and pregrouting through to the final grout tightening of the rock/plug interface and the surrounding rock. This paper is one in a series of papers detailing other aspects of the project, which was constructed largely between May 2001 and August 2003.

Jan 1, 2006

By N Winkelmann

Underground coal heating is a significant hazard in some coal mines. The broad principles of how underground coal heatings occur is reasonably known, however the technique for locating the heatings in often inaccessible goaf has been proved to be difficult. Since 2002, CSIRO, with the support of the Australian Coal Association Research Program (ACARP) has been undertaking investigations to apply and develop innovative surface-based radon technique for locating the underground heatings in Australia. This paper presents the progress of the investigation.

Jan 1, 2005

By H J. Stedman

A Transient Electromagnetic (TEM) geophysical survey was trialled in Bowen Basin Permian coal measures overprinted by Cretaceous intrusion. The trial’s intention was to compare whether TEM could assess residual coal more accurately and economically than drilling.TEM results were promising but had limitations. TEM did not compare to drilling for defining coal thickness or relative level definition. However, TEM resolved conductive anomalies laterally; providing a qualitative picture of remnant coal.Three material types and associated conductivities occur within the trial area: overburden (sandstone/siltstone), intrusive sills and heat affected coal.Ground conductivity was analysed by measuring decay of residual current within the TEM loop. Fast decay related to resistive overburden and intrusion, attenuated decay related to conductive coal.Generally speaking, carbon content governs coal resistivity where good quality, low ash, bright coal is more resistive relative to dull, high ash coal. Though in the trial area, relative to intrusion and overburden, coal was found to be the most conductive of the three materials.By modelling conductive anomalies, a general picture emerged of remnant coal regions. Subsequent highwall exposure reconciled with conductive TEM anomalies.CITATION:Stedman, H J, 2017. Findings from a transient electromagnetic trial for heat-affected coal, in Proceedings Tenth International Mining Geology Conference 2017, pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

By R. A. Hodge

Over the past decade, there has been a significant increase in effort put to tracking progress toward sustainability. Many aspects of society are participating in this “movement” including mining. The drivers are diverse and include evolving ideas in business and public administration as well as concerns for human well-being, community robustness, environmental integrity, and overall social and ethical responsibility. The scale in question varies greatly from local to global. For the most part, there has been a pre-occupation with developing discrete measurable signals. This paper argues that the overwhelming focus on the quantitative is ill-advised and that a more effective approach is to bring together the best of both quantitative and qualitative. The mining industry in particular is well-placed to affect this shift and reap the associated benefits.

Jan 1, 2004

By Glenn K. Nolan

"Today, more than any other time in recent history, aboriginal communities are looking for ways to be understood as more resource development companies continue to explore and develop Canada's vast resource potential.Recent Supreme Court rulings have affirmed the need to engage aboriginal communities early on in resource development projects. There are many conflicting ideas on how, who, and when to engage. Given the large number of communities and varied cultures, each resource development company must equip itself with a better understanding of the people they are planning to work with.The lecture will begin with a basic historical perspective on treaties and the various societies across Canada. We will also explore the current situation many communities find themselves in today. Building a meaningful relationship with a community is the foundation for a lasting partnership. Every community is unique and every approach to engage communities must be just as unique. The lecture will outline some basic steps that can lead to a better relationship building process between the communities and companies."

Jan 1, 2008

By S. Banisi, M. Poorkani

The Sarcheshmeh copper deposit contains 1 billion tones of ore averaging 0.7% copper and 0.025% molybdenum. It is located southeast of Iran and currently processes 41,000t/d. Molybdenite as a by-product is recovered in two separate stages. First, a bulk coppermolybdenum concentrate is produced and in the second stage these two are separated. The recovery of molybdenite in the first and second stages is 65% and 85-90%, respectively. The yearly production of molybdenite concentrate varies between 3500 and 4000 t. Sodium sulphide is used as the depressant of the copper and iron bearing minerals which due to a rather high consumption (17.7 kg/t) constitutes one of the major cost items of the plant (i.e., 58% of total reagents cost). A detailed laboratory scale study showed that replacing air with nitrogen could reduce the consumption of sodium sulphide (i.e., H2S or mineral origin). Nitrogen for the plant was supplied from an oxygen plant used for the smelter through a 1400 m long pipeline. The existence of the oxygen plant at the Sarcheshmeh complex was a key factor in the implementation and success of this project. After using nitrogen in the plant for a period of twenty one months, the consumption of sodium sulphide was reduced from 17.7 to 14.2 kg/t at constant metallurgy. The reduction was lower than expected which was mainly due to the type of sodium sulphide used and the lack of any automatic instrument to control the depressant (sodium sulphide) dosage. The latter in turn caused the operators to overuse sodium sulphide in order to reach and maintain the target metallurgy (i.e., higher molybdenite recovery along with lower copper content of the concentrate).

Jan 1, 2005

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

By M. H. Weinecke, B. P. Faulkner

This paper will discuss the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and finally a discussion of the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last ten years. Many clay-like materials, such as coal-fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce a commercially saleable LWA.

Jan 1, 2001

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By J. Barrett

State-of-the-art wireless communication and location-tracking technologies will dramatically change the face of mine worker safety. The MineTracer System developed by a Liberty Lake Washington company is a broad capability wireless sensor network based on a new breed of technologies known as wireless mesh systems. In this paper, R&D Manager Jim Barrett summarizes the balance of engineering tradeoffs that result in a system that (1) performs well, (2) is survivable against many types of mine accidents, (3) operates for many hours post-accident on battery power, (4) meets stringent MSHA requirements for intrinsic safety, and (5) is economically affordable for the mines.

Jan 1, 2009

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By G. Gabra

The kinetics of acidified thiourea leaching of pyrite concentrate was investigated at temperature ranging form 20 °C to a 60 °C. The effect of various parameters on the dissolution rates are discussed. The gold extraction was found to be zero and first orders with respect to Fe (111) and thiourea concentration, respectively. The order of the reaction with respect to sulfuric acid was found to be zero. The activation energy was determined from the Arrhenius plot as 2,039 kcal mole -1 (for a freshly prepared acidic solution containing Fe (111) as the oxidant and at 800 rpm stirring speed. This relatively low activation energy value suggests that the gold extraction is controlled by a-physical phenomenon. Under optimum conditions, more than 90% of gold has been dissolved in about 30 min. and 95% in 60 min. Attempt to recover gold from thiourea solution using active carbon is also discussed.

Jan 1, 1984

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

New Bio-Adsorber with Activated Carbon and Nano Tube Carbon for Separation of Nickel and Cadmium

Sep 13, 2010

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

By G. Belardi, N. Shehu, L. Passeri

"This paper illustrates the possibilities of applying what is essentially a physical soil-washing technique for treatment of soil contaminated by semi-volatile hydrocarbons in order to reduce the level of pollution to that permitted by Italian regulations.The ground around a factory producing lubricating-oil additives consists of silty-sandy soils which have long been contaminated by heavy hydrocarbons, especially branched alkyl benzenes and naphthalene derivatives. Pollution is particularly marked in some zones (hot-spots) where Total Petroleum Hydrocarbon (TPH) values are as high as 7000 ppm. The hydrogeological characterization showed the presence of a gravely soil in a sandy/silty matrix, with big stones making preferential paths to the water circulation. The permeability is 10-5 m/s and the water-table occurs at about 3 m below ground level.After laboratory and pilot-scale studies on representative samples of in-situ soils with TPH between 2700 and 7000 ppm a flow-sheet is proposed for reducing TPH values below the acceptable limits in Italy, namely 700 ppm for hydrocarbons with more than 12 carbon atoms and less than 250 ppm for those with fewer.On the basis of indications provided by laboratory tests a mainly physical treatment process of soil washing has been developed. This is used to clean-up soil from a site polluted by non-volatile hydrocarbons with a high TPH value. The process involves a high-density attrition stage followed by wet screening at 0.5 mm and then wet-gravity separation of the minus 0.5 mm fraction in the centrifugal field.The gravity separation products consist of a light fraction with particle size finer than 15 micron which contains most of the pollutants, and a heavy coarse fraction with TPH values conforming to the limits set by Italian regulations (less than 700 ppm hydrocarbons whose structure contains more than 12 C atoms, and less than 250 ppm of hydrocarbons with less than 12 C atoms)."

Jan 1, 2003

By Tuan V. Nguyen, Louis Mittoni, Murray Rudman, CSIRO Minerals, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D “Improving Thickener Technology” project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By R. L. Grunes, F. K. Kies, C. D&apos, Antonio

THE several studies concerned with the annealing of thin nickel films have largely been restricted to films of a single thickness.1-4 It is well-known, however, that both physical and mechanical properties depend upon film thickness.5, 6 The strength-thickness relations found in vapor-deposited nickel films in the annealed and as-deposited states, as an example, are at least partially due to the density and arrangement of imperfections within the films.7, 8 For these reasons, the annealing characteristics of thin nickel films as a function of thickness were investigated. Electrical resistance was chosen to monitor annealing behavior since resistance changes are partially dependent upon defect structure. In addition, the equations predicting film resistivity as a function of thickness are already available.9, 10 Further advantages afforded by electrical-resistance measurements are its adaption to continuous readings during annealing and its relative simplicity. Nickel films were vapor-deposited, at average rates of 60Å per sec, on Vycor substrates held at room temperature in vacuums of about 10-5 torr. Afterwards, deposition-thickness measurements were made using a multiple-beam interferometric technique. A more detailed description of deposition procedures and the interferometer appear elsewhere.7, 8 The four-probe method was employed in measuring electrical resistance since this technique measures film resistance without contributions from lead wires and contacts. Resistance measurements were made before, during, and after annealing to temperatures of 700°C under vacuums of approximately 10-4 torr. Measurements were made every 25°C or more often when necessitated by unusual resistance changes. Cooling and heating rates were maintained at approximately 5°C per min. Typical resistivity vs temperature curves are shown in Figs. 1 through 4. It is apparent from these

Jan 1, 1965