Search Documents

Reduce the cost of modifying uranium well casings so that leaching solutions can pass through, but sand grains are blocked. Approach The well casing and surrounding cement are perforated at the mineralized zone by impinging them with high pressure water jets. How It Works A nozzle assembly is attached to a high pressure (15,000 psi) pipe and lowered into the well casing which typically is schedule 40 PVC (poly-vinyl chloride). The high pressure pipe line is extended down Into the casing until it reaches the mineralized zone. The upper end of the pipeline is then connected by a high pressure hose to the outlet of a 10,000 psi pump. Turning the pump on for 5 seconds causes a high velocity water jet to cut through the well casing and the surrounding cement. Figure 1 shows a high pressure pipe being installed in a well casing. Cutting small diameter holes in the casing allows the leachant to enter the casing and be pumped to the surface. However, the holes are small enough to prevent most sand grains from entering. Numerous holes are usually cut through the casing. The 3-nozzle assembly shown in Figure 2 cuts three holes, one above another.

Jan 1, 1978

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976

By A. W. Breed

The bioleaching of arsenopyrite, the oxidation of arsenate and the precipitation of ferric arsenate are competing reactions, hence their rates depend on the relative concentrations of the respective species, and the activity of the bacterial culture. Bacterial arsenic resistance may be attributed to the Pst+Pit-mutation and an energy dependent efflux pump. Pst+Pit-mutations result in a reduced uptake of arsenate. This enables the bacteria to survive in solutions in which the arsenate concentration is significantly higher than the arsenite concentration. However, the excretion of arsenate requires energy. Therefore, in the absence of an energy source or during periods of reduced bacterial activity, the inhibitory effect of arsenate may manifest at concentrations to which the culture has been adapted. The chemical ferric leaching rate of pyrite and arsenopyrite decrease with a decrease in the solution redox and may be described using a modified Butler-Volmer equation. The bacterial ferrous-iron oxidation kinetics of L. ferrooxidans also depend on the redox potential, and can be described using a Michaelis-Mententype model modified to account for both temperature and pH. A model developed using the independently determined ferric leaching, and ferrous-iron oxidizing kinetics, has been shown to compare well with the experimental data for the continuous bioleaching of pyrite. Keywords: Leptospirillum ferrooxidans, arsenopyrite, bioleaching, sulphide minerals ferrous-iron oxidation kinetics, ferric leaching kinetics, redox potential

Jan 1, 2000

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008

The Pogo Mine, near Delta Junction, Alaska is a new 2500 STPD gold operation. The control system of the mine and milling operations are a hybrid of DCS (Distributed Control System) control and PLC (Programming Logic Controller) control. A DeltaV DCS system serves as the main control and operation platform while the PLCs operate a multitude of vendor specific packages. The communication backbone of the DCS system is a hybrid of star and ring fiber optic topology, which provides reliability and flexibility. The communication between the DCS and PLCs is typically facilitated by serial communication. This communication insures the integrity of the whole control system.

Jan 1, 2008

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

Water rights and availability are extremely contentious issues in many mining regions around the world, in some instances leading to violent confrontation. This situation has the potential to only get worse because competition for &apos;scarce&apos; water resources will increase with population growth. In this environment the dilemma facing the mining industry is how to generate confidence in developing a responsible, sustainable and transparent water management strategy that is recognised as such by all stakeholders. Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Another contentious aspects of new mine development is the debate between all stakeholders on the amount and quality of water that a mine is able to discharge into the environment should this be required. There are a multitude of water resources available to the mining industry for operational needs however much of this water is saline and over the last two decades there has been a continual decline in water quality (ie salinity has increased). In today&apos;s world there are enormous internal and external pressures to reduce water consumption at a mine and/or alternatively use water not considered a resource by the local community (ie sewage, saline or salt water, desalinated water). Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (ie by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing. Recycled water, acid mine drainage water and water collected in the mining area have the potential to impact mineral processing performance, unless they are treated, because of the build up of mineral salts and decomposed chemical products in these types of waters. Besides this the regulatory requirements of any water discharged from a mine site (quantity and quality) have also become more stringent. For these reasons there is now some form of water treatment practiced at most mining operations around the world. This paper provides an overview of water stewardship undertaken in the mining industry over the last two decades and provides examples of water treatment practices that have recently been installed at mining operations that may be of interest to the reader.

Sep 13, 2010

By D. A. Payne

Large excavations, such as Iongwall panels, result in extensive vertical stress redistribution in the surrounding strata. The large abutment stresses developed may produce damage to pre-existing or planned excavations in the same seam or in seams above and below the workings. Knowledge of the magnitude and location of these stresses is therefore important in the design of mine openings; pillar sizes for panel and pillar layouts, roof supports in longwall gateroads and workings over or above pre-existing or planned extraction in adjacent seams. In an attempt to reduce costs, the Cape Breton Development Corporation (CBDC), a Federal Crown Corporation responsible for operating two retreat longwall coal mines, examined the potential for either interpanel barrier pillar width reduction or entire pillar elimination by the adoption of dual life gateroads for the longwall panels. In order to assess the potential for reduced interpanel barrier widths or total elimination, an investigation of the redistribution of vertical stresses around longwall panels in the Sydney Coalfield was established. The study was conducted jointly by the Cape Breton Coal Research Laboratory (CBCRL), of CANMET (a division of Natural Resources Canada) and the Denver Research Center (DRC) of the United States Bureau of Mines. The program included monitoring of vertical stress changes around longwall panels and gateroad behaviour in two seams. USBM-style hydraulic borehole pressure cells connected to chart recorders for continuous monitoring were deployed at four sites, two at Lingan Colliery and two at Phalen Colliery. This report describes the investigations conducted at Phalen Colliery. Contoured plots of stress redistribution around two sites are presented.

Jan 1, 1995

The paper reviews the results emanating from an experiment conducted in Bochum?Germany in which various international rope inspection authorities were requested to assess the conditions of a corroded rope sample as well as a rope sample containing internal fatigue breaks. Both samples were of the multi-layer low rotation construction.

Jan 1, 2000

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

By Francois E. Heuze

INTRODUCTION Rock slope stability typically is governed by the geological discontinuities. This stability can be improved by drainage, unloading, adjustment in slope orientation, adjustment in slope angle, and also by reinforcement such as bolts or tendons. This paper addresses the modeling of bolt reinforcement in rock slopes. Most geological discontinuities such as joints have rough surfaces; they dilate during shear displacement. Their shear strength is characterized by two envelopes (Fig. 1); the peak envelope is distinct from the residual envelope when the joints can dilate. If the dilation is restrained transversely, such as with bolts, the normal stress will increase and the joint strength also will increase. It has been demonstrated that this increase may be considerable (Obert et al., 1976). The new normal stress at peak strength is a com- posite function of the properties of the rock mass and of the steel (Heuze, 1979). Hence, the dilation and its resultant effects on joint shear strength must be included in the analysis and design of the reinforcement. We present a model which can be used to perform such an analysis. Early studies of rock reinforcement in mining and civil applications (Lang, 1957 - Panek, 1962 - Osen and Parsons, 1966 - Lang, 19721, did not consider the specific effects of bolts on joint shear strength. In 1973, Heuze and Goodman reported direct shear tests on rough sandstone joints with bolts perpendicular to the joint plane (Fig. 2). The peak shear strength of such joints was greatly in excess of the shear strength of the unbolted joints. The excess

Jan 1, 1983

By Richard B. Berg

Chlorite veins in the Silver Star district (40 km southeast of Butte) were of little interest to those who were mining gold and silver in the late 19th century. It wasn&apos;t until 1975 that unusually pure magnesian chlorite of the variety clinochlore was identified from a ?talc? claim in this district. In 1977 tests by Cyprus Industrial Minerals showed that this chlorite was suitable for use in ceramics. Mining begun in that year continues. These replacement veins of chlorite in Precambrian quartzofeldspathic gneiss differ from the metalliferous veins to the northwest in both attitude and mineralogy.

Jan 1, 1982

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By Dana C. Reinke, David K. I Ingram

Researchers at the National Institute for Occupational Safety and Health partnered with the water well industry to develop engi­neering control technologies and training products to address noise exposure at the job site. Noise­induced hearing loss continues to be a problem in the well drilling industry. Research con­ducted by NIOSH found that air rotary drill rigs produce sound levels more than 90 dB(A) over the course of an eight­hour workday. Sounds levels above 90 dB(A), identified during hammer drilling and the hammering of casing, exposes workers to levels that can damage hearing. A typical air rotary drill rig provides no barrier, for noise and dust pro­tection, between the drill’s control panel and the drill stem. The development of a partial cab is the clearest example of NIOSH’s research partnership with the water well industry. NIOSH researchers determined that an engineering noise control to protect the oper­ator at the rig’s control panel would be effective, based on typical work site conditions. Many surface rigs do not have full cabs as a result of the original equipment manufacturer design or the high cost of aftermarket products. Developed as a partial cab, the NIOSH engineer­ing noise control design addressed stakeholders’ needs associated with cost, transport, and worker usage (Figure 1). Field tests found the partial cab effective in reducing sound levels at the rig’s control panel, a typical location for a drill rig operator. Sound levels at the control panel were reduced from 104 to 96 dB(A) (Figure 2). Coupled with continued use of personal protective equipment, such as hear­ing protection devices, the partial cab can help to reduce noise exposure. NIOSH researchers created a CD with informa­tion about noise exposure and the partial cab. Most important to well drilling companies is information on how to construct and attach the partial cab to drill rigs. The CD can be viewed on a standard computer and includes a video of the partial cab in use on a work site. Computer­aided design drawings are included on the CD and provide detail of the cab design as well as information on construction mate­rials and design details. Additionally, the CD provides background infor­mation on noise­induced hearing loss and hearing protection devices to increase knowledge about this occupational health concern. This information can be viewed by all company employees to help promote the partial cab’s importance to workers using the cab. More information on the partial cab noise control technology can be downloaded from www.cdc.gov/ niosh/mining NIOSH researchers also examined the health and safety training needs of workers in the ground water industry. It was quickly realized that most workers learn health and safety on the job and do not attend any sort of formal training. In addition, there is not a lot of time for daily “tailgate talks” or “shop talks” on health and safety issues. As a small business industry, the owner is often operating a drill rig along with his other employees. In general, new employees learn the job in an apprentice style sys­tem. As a result, workers and owners have few opportunities to access uniform health and safety information based upon the job — an outdoor work environment with daily change in work sites. With this information, NIOSH researchers devel­oped two products that deliver health and safety information to fit into the daily work of well drillers. Both are information circulars and are available through download at www.cdc.gov/niosh/mining and the NGWA Web site at www.ngwa.org/publication/ publications.cfm. These circulars are: Water Well Safety Bits. This booklet provides information in a “quick bites” style. It is pre­sented in a magazine format and can be left on

Official Program

Jan 8, 1950

By Hillis R

As part of BHP Iron Ore&apos;s policy and goal of achieving a high standard of environmental management within its operations, a protocol for mine closure has evolved. The need to demonstrate sound environmental management with respect to site decommissioning meant that a comprehensive, environmentally sensitive closure protocol was required. Within this framework, a four-phase protocol was developed, the first phase was the determination of objectives in relation to site rehabilitation and end land use. The second phase was the determination of the process required to achieve these objectives. The third phase was the application of this process in a site specific manner. The fourth and final phase was monitoring of the site with regard to the achievement of determined objectives. The protocol was originally developed to direct the closure and decommissioning of the Goldsworthy site in 1992. This being the first total site decommissioning for BHP Iron Ore. Since that time the protocol has been successfully utilised for the closure of the Yampi (Koolan Island) operations (in 1993/94) and the Shay Gap/Nimingarra Operations (in 1994/95).

Jan 1, 1996

By Peter K. Mathison

The U. S. Department of Interior, Bureau of Mines (Bureau) is developing a hydrologic monitoring system for in situ leaching operations. A working prototype of this system was installed and tested at the Cyprus Casa Grande copper mine. Requirements specific to in situ leaching operations were identified by researchers. The system has been a useful tool for researchers and for mine personnel. Observations of the hydrologic monitoring system, including details of the development process, the design of the system, and the software developed at the Bureau have resulted in new ideas for an enhanced design of the system.

Jan 1, 1992

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20&nbsp;million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1&nbsp;mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010