Search Documents

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By K. H. Heino

Two 200 T/da Lurgi Turbulent Layer fluid-bed roasters have been in operation at Canadian Electrolytic Zinc Limited since 1966. Zinc concentrate containing 52-54% Zn, 9-11% Fe,31-33% S is treated to produce calcine containing 60-62% Zn,10-12% Fe, .l-.3% S as sulphide and .8-1.2% S as sulphate. Each roaster train comprises a waste heat boiler, two cyclones in parallel and a two-field electrostatic precipitator. Distribution of calcine collected is 10-15 percent from bed overflow, 55-65 percent from boilers, 20-25 percent from cyclones and 2-6 percent from precipitators. A Monsanto designed contact plant produces acid at a rated capacity of 365 T/da (100% H2304 basis) from roaster gases diluted to 7.0-7.5% S02. The process steps are gas cleaning and cooling by weak acid scrubbing, acid mist removal in electrostatic precipitators, gas drying in 93.5-96.5% H2304, conversion of sulphur dioxide to sulphur trioxide in a four-pass converter containing vanadium pentoxide catalyst, and absorption of the sulphur trioxide in 98.1-98.3% H2S04. Product acid is 93.2% H2S04. Conversion efficiency is 97-98 percent and overall sulphur recovery from concentrate is 87-90 percent. The adjacent fertilizer plant has a capacity of 135 T/da of P205. The products are 54 percent phosphoric acid, run-of-pile triple superphosphate, and diammonium phosphate. The plant is of Ugine-Kuhlman design and consists of an air-cooled multiple tank reactor, a tilting pan filter, and a forced circultation vacuum evaporator. Triple superphosphate is made on a continuous belt and partially cured in a rotary dryer. Diammonium phosphate is produced by ammoniating phosphoric acid in a single stage reactor. The slurry of ammonium phosphate is granulated in a blunger and dried.

Jan 1, 1970

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

The main objectives of the Mine Mechanisation and Automation program (MMAP) are to enhance health and safety in underground mining operations, facilitate mechanization and automation in narrow-vein and deep mines, provide sound science to regulatory agencies and improve mine profitability. The program, which has a unique underground and surface industrial scale facility, is involved in many multi-partner projects, like hydrogen fuelcell applications, electrification and hydraulification of underground mines, reduction of noise and vibration, miner location device, explosive-free blasting and hoisting. The paper presents an overview of the Mine Mechanisation and Automation Program of Natural Resources Canada and some of the main projects.

Jan 1, 2002

By M. Gous

Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC-arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC-arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilization and furnace stability, complemented by continuous improvement drives, will be thevehicle to drive performance in the short-term, with longer-term performance enhancements due to strategic process development. Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC-arc furnace, titania slag, pig iron

Jan 1, 2006

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

By R. B. Tippin

Great Salt Lake Minerals & Chemicals Corporation (GSL), a subsidiary of Gulf Resources & Chemical Corporation, is located on the east side of the Great Salt Lake, approximately 20 miles from Ogden, Utah. GSL processes brine from the north arm of the lake to produce potash, salt cake, salt and magnesium chloride brine. Potash fertilizer, in the form of K2SO4 is GSL's primary product. The GSL Sulfate of Potash Complex The GSL potash complex (depicted in Figure I) is divided into a solar evaporation pond system and the process plants. The solar,evaporation system consists of a 17,000-acre (68.8 Km2) ponding operation where the various salts deposit during the summer evaporation season, and a harvesting operation which recovers the deposits during the remainder of the year. The harvest is either preconcentrated in the flotation plant or processed directly in the chemical plant where sulfate of potash (SOP) is produced. The chemistry of the lake brine results in a solar deposit con¬taining primarily kainite (KCl-MgSO4.3H20), schoenite (K2SO4?MgSO4^ 6H2O), and halite (NaCI), with some carnallite (KCl.MgCl2.6H20) and epsomite (MgSO4.7H20). Other minor minerals may be deposited, depending upon the weather during the evaporation season. Each year, the solar deposit in the evaporation ponds will greatly depend upon the summer weather conditions, which have in the past proven to be quite unpredictable. Weather may alter both the quantity of the solar deposit and the composition of this deposit. During, a "short" evaporation season, the tonnage deposited decreases, but depending upon the short-term weather, the potash mineral content

Jan 1, 1977

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974

By P. Sangurmath, C. Gundewar, M. Riyazulla, V. Vasudev, N. Shadaksharswami

Dharwar craton in the southern Indian shield, comprises the Neoarchaean foreland in the west and a relatively younger accretionary complex composed of granitoids and intervening gold-bearing volcano-sedimentary belts. The Hutti schist belt hosting a major gold producing mine is situated in the northern part of the eastern Dharwar craton. It is a horse-shoe shaped structure comprising predominantly of pillowed metabasalt of tholeiitic composition with minor amounts of clastic sediments and felsic volcanic rocks. The belt is intruded on all sides by circular to tabular bodies of granites and granodiorite. Important gold deposits are located at Hutti, Hira-Buddini and Uti villages. Felsic volcanics in the Hutti belt occur as tabular bodies of quartz porphyry and breccia. Two of the gold-bearing reefs in the Hutti mine, Viz., Middle and Strike reefs are intimately associated with tabular sub-vertical sheets of mylonitic quartz-feldspar porphyry intruding pillowed metrabasalt. In Uti mine area, the felsic volcanics occurs as a tabular body. At Hira-Buddini, the felsic volcanic occur as a irregularly shaped sheet in pillowed metabasalt. Mineralogical and geochemical studies suggest that the felsic volcanic rock in Hutti mine area is a rhyolite and at Uti and Hira-Buddhini it is of dacite composition. Scheelite occurs as veins, veinlets, stringers and blebs along fracture planes of felsic volcanics in the Hutti mine area, whereas at Uti and Hira-Buddini it is insignificant. On the basis of spatial association of metabasalt and felsic volcanics and on geochemical grounds, we interpret that the felsic volcanics might have originated by the partial melting of basalt. REE patterns of the granite, granodiorite and metabasalt of Hutti are similar to each other indicating that they could be co-magmatic. However, REE in the Hutti felsic rocks is significantly higher than in Uti and particularly Hira-Buddini mine areas. The two felsic volcanic samples drawn away from the mineralized zone from all the three mine areas were analyzed for tungsten. In Hutti one sample assayed 0.15% and another 0.062%. At Uti, in one sample it assayed 0.056% and another less than 1 ppm, whereas at Hira-Buddini, it is less than 1 ppm in both the samples. The spatially associated basalt analyzed 23 to 235 ppm tungsten, whereas granites and granodiorites have very low (<1 ppm) tungsten. Therefore, the source of tungsten in the felsic volcanics of Hutti area could be traced to metabasalt. The absence of significant amount of tungsten in the felsic volcanic of Hira-Buddini could be attributed to the lack of REE enrichment compared to REE in Hutti and Uti felsic volcanics.

Jan 1, 2007

By H Mali, B Kain-Bückner

Different types of lump iron ore-bearing particles were investigated in terms of their raw material properties depending on their behaviour during reduction. To predict the reduction behaviour different types of lump iron ore and pellet brands were characterised by their mineral abundance, texture and pore size. The image processing software VisuMet was developed to semi-automate the evaluation of photomicrographs from polished sections of lumpy iron particles. The results were compared to the standard reducibility test after ISO 4695. The evaluation of lump iron ores is based on the simulation of the transformation of the different iron minerals due to their sequence of reducibility. The progress of the reduction front is simulated and the result is a degradation curve. Pellets were also investigated due to their different pore size distribution. The results indicate that the pore size influences the reducibility in addition to mineral abundance. The evaluation with VisuMet of the lump iron ore and pellet samples correlates with the reducibility provided by the ISO 4695 test. The determination of the mineral abundance by VisuMet is comparable to common point counting with a correlation coefficient of 99.67 per cent.CITATION:Kain-B&#252;ckner, B and Mali, H, 2017. VisuMet – analyses of lumpy iron carriers with image processing, in Proceedings Iron Ore 2017, pp 557–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Manuel Sanchéz

Para las empresas mineras, la búsqueda de buenas condiciones con los clientes y la optimización de los procesos involucrados en la cadena de valor, es uno de sus principales objetivos. En este sentido, el presente texto señala las estrategias y soluciones que priorizen y mejore la calidad de las decisiones en la empresa.

May 25, 1998

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

concentrations) and physical nature of receiving streams, which in turn affects the stream ecosystem. Benthic macroinvertebrates are used to illustrate these impacts, and to investigate natural recovery in affected streams. In Charming Creek, a severely impacted stream in the Buller District, the macroinvertebrate community recovers diversity and the proportion of sensitive species (EPT) in the community is more significant with increasing downstream distance from the source of AMD. This is most likely due to dilution of AMD contaminated water by tributaries to the Charming Creek mainstream. Other impacted systems with less dilution from tributaries did not display similar levels of recovery. The effectiveness of remediation products BauxsolÖ and Zeolite was investigated using laboratory trials. Both products mitigated the toxicity of AMD and enhanced the survival of mayflies exposed to AMD contaminated water. Such products may be of use in the New Zealand environment but are likely to be most effective in conjunction with other systems (eg wetlands). Mitigating the impacts of AMD on stream ecosystems needs to include systems to directly address water chemistry issues (low pH, high metal concentrations) as a component of a holistic approach to restoring environmental conditions.

Jan 1, 2003

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon&apos;s economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country&apos;s only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon&apos;s gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon&apos;s ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985