Search Documents

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By Anna Kate Miller, James J. Brady, Hamza Jaffal, Ritika Sangroya, Chadi El Mohtar, Wing Shun Kwan

"The design of an appropriate pre-grouting program can be the difference between a successful tunnel construction and an expensive on-the-go repair. However, current grout design relies heavily on rulesof- thumb and outdated charts. The geotechnical investigation is rarely targeted towards grouting design and the final grouting decisions are made based on fines content or soil classification. The current paper presents an experimental study performed to determine the optimal grout for a tunnel in soft ground below the ground water table (GWT). The testing program consisted of sieve analysis and undrained static triaxial tests on reconstituted sonic samples. Rheological tests were used to compare the different grout mixes and identify best candidates before performing one-dimensional permeation tests. Pressure and volume measurements during the permeation tests, along with the unconfined compression strength results on the permeated soils, helped evaluate the filtration potential for the different grouts and select the optimal grout.INTRODUCTIONConstruction of the Millwoods Double Barrel Replacement Project commenced in 2009 and was expected to be completed by 2015. To facilitate ongoing city development in south Edmonton, the City implemented construction of a major sanitary trunk network along 91st Street and 30th Avenue. The project involved the design and construction of approximately 1.2 miles (2 km) of 7.8-ft (2,400 mm) sanitary tunnel and 2.1 miles (3.4 km) of 11.5-ft. (3,500 mm) and 9.5-ft. (2,900 mm) storm tunnel. Part of the project also involved the conversion of the existing double barrel storm and sanitary trunk to full sanitary service, and reconnecting the local storm sewers from the double barrel pipe to the new storm tunnel. The tunnels range in depth from 26-ft. (8 m) to 115-ft. (35 m) and are being installed using a one pass system with precast concrete segmental liners."

Jan 1, 2016

The Dizon open pit mine of Benguet Corporation in western Central Luzon, Philippines has yielded some 182 000 t copper, and about 26 000 kg gold and 48 000 kg silver as by products since it started operation in November 1979. The 140 million tonne orebody is associated with a small quartz diorite porphyry stock emplaced in volcanic rocks on the basal slope of a stratovolcano complex as stockworks, fracture fillings and disseminated sulphide mineralization averaging 0.43% Cu, 0.93 g/t Au and 2.5 g/t Ag. Intense hydrothermal alteration accompanied the mineralization that developed fairly distinct mineral assemblages within and around the intrusive. Post-ore volcanic activity later gave birth to an upward-flaring diatreme which broke out south of and adjacent to the orebody and partially destroying it. Subsequent volcanic activity buried the mineralized area along with the rest of the stratovolcano's surrounding slopes under a thick deposit of pyroclastic and laharic debris. Erosion eventually removed the volcanic cappings over Dizon and also exposed the quartz diorite porphyry stock which might have resulted in the truncation of a sizeable section of the Dizon deposit. The chain of stratovolcanoes that comprise southeastern Zambales range hugging the southeastern edge of the Zambales ophiolite is part of a west-facing volcanic arc that extends for some 300 km along the western margin of central and southern Luzon whose development has been correlated to the subduction in the Manila Trench located off the west coast of Luzon. Prominent WNW-trending lineaments that cut across the ophiolite appear to be splays of the Philippine Fault whose intersection with the Mt. Pinatubo stratovolcano complex might have localized the emplacement of a number of intermediate stocks along with the gold-rich porphyry copper mineralizations associated with some of them.

Jan 1, 1987

By B Rohrlach, J Gonzalez, A Buenavista

Located on the island of Mindanao in the Southern Philippines, the Tampakan copper-gold deposit represents a major high-sulfidation epithermal deposit superimposed on an underlying porphyry copper system. With a recent JORC compliant indicated and inferred resource estimate of 1104 million tonnes at 0.65 per cent copper and 0.26 g/t gold at a 0.3 per cent copper cut-off grade, Tampakan represents the largest undeveloped copper-gold deposit in Southeast Asia. Since its acquisition by Indophil ResourcesÆ affiliate Sagittarius Mines Inc in August 2002, the deposit is the subject of an ongoing preliminary feasibility study into project viability that is initially focused on a higher-grade copper zone in the north-central part of the deposit. The deposit is hosted by a sequence of subaerial andesitic flows (Tampakan Andesite Sequence) related to a highly eroded andesitic stratavolcanic complex of Pliocene age. Detailed mapping and geochronological dating has identified four volcanic cycles or centres that have been sequentially developed and eroded. This stratovolcanic complex is interpreted to lie on the northern extension of the Sangihe volcanic arc that extends from Northern Sulawesi in Indonesia. The Tampakan district is located within a complex tectonic setting dominated by WNW trending wrench faults that form part of the trans-Mindanao Cotabato Fault Zone. The Tampakan deposit is located near the intersection of one of several WNW trending splay structures with a prominent NNE trending dilational structure, one of many that transect the host volcanic complex. High-sulfidation style copper-gold mineralisation at Tampakan is broadly associated with and central to a flat-lying tabular body of pervasive silica and silica-clay alteration developed within a district- scale lithocap of advanced-argillic and argillic hydrothermal alteration that extends over an area of 90 km2 within the volcanic complex.

Jan 1, 2004

By J. Gardner Brooks, Sidney Sigel, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By Fletcher A. E W

Ever since it made its debut in 1962, in the form of a Robbins 31R, the raiseborer has become an accepted tool in the mining and civil construction industries. The first raiseborer to be used in the Witwatersrand goldfields made its appearance in 1968. This was a Robbins 42R which could raisebore 185m deep holes to 1,22m diameter. From 1968 to 1973 capability increased with the introduction of first the 61R, then the 71R and finally the 83R, which could raisebore 610m deep holes to 3,66m diameter. This created a demand for larger holes but the cost of bigger, more powerful machines requiring larger, stronger drill pipe, cutters and other accessories was prohibitive. To avoid replacing existing models such as the 71R, and in order to increase their capability, the concept of reaming in two stages sequentially was developed jointly by a German drilling equipment manufacturer, Wirth, their South African subsidiary, Transbor, and a local contractor, Rocbor Raiseboring and Mining Contractors. The result, the Sequential Reaming Head, proved most successful and existing machines, normally limited to 2,44m diameter holes, could now ream to 3,66m diameter. This created a demand for even larger holes. In order to maximise the use of the sequential reaming head to meet this demand the HG330, and subsequently the HG330SP raiseborer were developed. Using a 4,26m/6,02m cutting head, these machines have raisebored holes 1000m deep in hard rock. The raise- boring of the first major hole to be excavated by this combination, the 484m deep x 6,02m diameter surface shaft at Premier Mine is described. Reference is also made to six other shafts which have been completed or are under construction.

Jan 1, 1987

The segment of the Upper Cenozoic volcanic chain (CVZ) located on the western border of South America (16-28¦S lat.) is constituted by an association of strato- volcanoes and ignimbrite sheets, with high K calco-alkaline affinities. Strata-bound volcanoes, mainly of andesitic and dacitic composition, present along the whole chain, and various hydrothermal alteration zones, on the slopes and in the cores of eroded volcanic structures. Some of these altera- tion zones bear epithermal precious metal ores and sulphur deposits, which at present are being exploited. The studied Salar de Gorbea area, located in the Andes of northern Chile (25-26¦S lat.) contains a numer- ous group of Miocene to Quaternary stratovolcanoes, with advanced argillic and extreme silicification hydrothermal alteration in their cores and on their slopes, favoring the formation of great volumes of alunite within altered zones and sulphur deposits in the higher parts of the volcanic edifices. Simultaneously, siliceous hydrothermal breccia of the phreato-magmatic type, with evidences of hydromag- matic explosions are recognizable, allowing, in some cases, the ascent towards the surface of rock fragments belonging to the Paleozoic pre volcanic basement. Radiometric ages obtained in some of the hydro- thermal alteration zones (K-Ar in alunite) are slighty young- er than the unaltered rocks which constitute the strato- volcano. Trace element (Hg, As, Sb, S, Au, Ag, Cu, Pb, Zn, Mo) patterns in orientative rock samplings show that the studied alterations zones correspond to high sectors of the cpithermal system, without evidences of metallic minerali- zation on surface. The weak erosive action due to the ex- tremely and climatic conditions in this segment of the Andes, has not allowed the cropping out of deeper areas of the hydrothermal alteration zones, in contrast to other Miocene more eroded volcanic edifices and Miocene vol- canic terranes of the Andean Range.

Jan 1, 1987

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By H. S. Venkatesh R. Balachander, G. C. Naveen

During the construction of a 1020 MW underground hydroelectric project in Bhutan a huge rock fall took place in the Downstream Surge Chamber (DSC) during March 2016. The total quantity of rock in the fall area is estimated to be about 1,50,000m3 (2.6 billion cubic feet), out of which about 25,000m3 (0.44 billion cubic feet) of muck was removed. The removal of muck was stopped apprehending that the cavity formed due to the rock fall may get further aggravated leading to widening and destabilising the adjacent transformer hall cavern or it might day light as the top cover was about 190m (623 feet). As the fall has virtually blocked the 314m (1030 feet) long cavern and divided it into two different chambers (south and north), and that the muck cannot be disturbed, it was decided to erect concrete wall on either side of the fall up to the cavern roof and then later address the filling of the cavity with appropriate fill material. As the access to the DSC was there for the southern side it was decided to extend a cable tunnel which was terminated at a distance on the north side of the cavern by D&B so that once it gets punctured into the north wall of the DSC it can be used to access the fall from this front too. This is a unique situation where in every blast approaching the DSC, the parting between them is diminishing and hence the tunnel blast will be exerting axial load on the parting wall leading to dynamic transient loading conditions and buckling may take place on the northern wall of DSC. This paper describes the various drill blast combinations adopted for successful excavation of this tunnel.

Jan 1, 2019

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By Golding S. D, Price P. L

The Early Permian Aldebaran Sandstone is the main hydrocarbon reservoir in the Denison Trough. Contained hydrocarbon gas has a wet gas index (C1/CI - C4) of between 0.87 and 0.97 (N=10), and constituent methane has 813CPDB values ranging from -51.5 to -36.2% (N=10). These values clearly indicate that the gas is thermogenic rather than biogenic. Considering the predominantly humic nature and maturity of all organic source material for the gas, the methane 813C values are anomalously low, with typical values for humic methane present in natural gas formed at similar maturity levels significantly higher at -26 ¦ 5%o. This suggests that, in addition to disseminated organic matter in underlying marine mudrocks of the Cattle Creek Formation, methane substantially more depleted in 13C was derived from coal seams of the Reids Dome beds, a thick coal measure sequence which underlies the Cattle Creek Formation and, in the south, the Aldebaran Sandstone. This methane is likely to have S13C values of between -75 and -40 oo, based on the known isotopic composition of dry gas trapped in humic coals of similar rank in the Sydney Basin and elsewhere in the Bowen Basin. In addition to the low methane S13C values, the contribution of coal seam methane would explain the fact that, (1) methane S13C values do not show the normal increase with decreasing gas wetness, and (2)013C%o (ethane-methane) values do not show the expected decrease with decreasing gas wetness. The presence of co-existing, isotopically heavy CO2 (S13C = +2.0 to +3.4%0, N=3) in the Glentulloch and Merivale Fields is consistent with the view that natural gas in the Aldebaran Sandstone is in part coal seam derived.

Jan 1, 1991

By A Cheatle

GoldcorpÆs Musselwhite mine in north-western Ontario, Canada has in recent years become a world-class deposit. Initially discovered in the early 1960s by Alan and Harold Musselwhite, the then marginal mine eventually started production in 1997 and has to date produced 2.6 Moz of gold. Two million ounces of gold are currently classified as Mineral Reserve and a further 1.2 Moz of gold are classified in the Mineral Resource category for a total gold inventory approaching 6 Moz. Growth of the mineral inventory has been achieved through the successful implementation of strategic planning that sought to extend the mine life through discovery of additional economic zones and increased mined tonnages. Accelerated exploration activity commenced in 2001, at a time when gold price was at its lowest in decades. Focus was placed on building, developing and retaining a highly skilled geological team, maintaining purpose, conducting external reviews and developing a new geological model through research partnerships. Ongoing collaborative research between Lakehead University and Musselwhite mine has seen the development of new structural and geological models through post-graduate and academic studies. Research has included lithogeochemical, stable isotope and structural and metamorphic studies and has led to the evolution of a new mineralisation model (for the mine) and the recognition of brittle and ductile deformation regimes within the mineralised horizons. Exploration drilling continues to provide support for the new geologic model. Gold discoveries have extended known mineralisation 2.3 km along strike from mineral reserves and laterally into parallel zones. The exploration potential to further increase production rates, Mineral Reserves and Resources remains very positive and increases in overall gold inventory are likely. Musselwhite mine has significantly exceeded initial projections for a ten year life-of-mine and a marginal existence.

Jan 1, 2009

By Robert B. Parsons

"For the fourth time in five years, residents of northern Canada have seen a change in the tax treatment of housing and travel costs. The latest changes announced in December 1990 by the Minister of Finance are to become effective in 1991. When will the tinkering stop?IntroductionFor man y years prior to 1987, certain travel and housing allowances received by employees in remote areas were generally considered by Revenue Canada to be tax-free, even though some observers suspected that such generous treatment was contrary to the provisions of the tax legislation. In the mid-eighties, Revenue Canada decided to reconsider the tax treatment of the mining industry's long standing practice of providing housing and travel assistance to these employees. The tax- free treatment was continued by virtue of annual remission orders, but only pending the enactment of legislation which would tackle the issue head-on and layout the rules in black and white to be seen by all. The sequence of events since then may be chronicled as follows:February 26, 1986-Finance Minister Wilson's budget present s the framework for the future tax treatment of travel and housing benefits provided to residents in remote regions of Canada.December 22, 1986-The Minister of Finance announces detailed rules to fill in the earlier announced framework.January 1, 1987-The new tax rules come into effect.April 29, 1988-The Minister of Finance announces the establishment of a Task Force to examine the existing criteria for determining the eligibility of residents of northern and isolated areas for tax benefits.October 27, 1989-The Task Force presents its report.December 7, 1990-Finance Minister Wilson announces a new system of tax benefits for residents of Canada's northern and isolatedregions.January 1, 1991-The new rules become effective."

Jan 1, 1991

By Richard E. Chism

Some years ago, when I was seeking an illusive fortune and gaining a precarious existence in the primeval forests of Brazil, there penetrated, even to my headquarters in that far-off land, the story of a new-found mining district, where mountain peaks were ribbed with silver, and valleys teemed with virgin gold. Such were the stories that caused hundreds of men to seek their fortune in Sierra Mojada, and to return heaping curses, loud and deep, upon the vivid imaginations that had evolved the glittering fiction. Nevertheless, the rumors had some foundation of truth. The ribs of silver exist, if not the placers of gold; and a flourishing town, of some three thousand people, with two leading mining companies and several smaller ones, in operation, represents what was permanent in the excitement of 1879. Geographical Situation. The town of Sierra Mojada is situated in the State of Coahuila, Republic of Mexico, in latitude 27' 24' N., and longitude 26' 40' W. of Washington, 4' 36' W. of the City of Mexico, and 103' 43' TV. of Greenwich. It lies about 70 miles, in an air-line, N. E. of Escalon station, on the Mexican Central Railroad; but by the present wagon-road, which makes a long detour to turn the mountain range, the distance to the station is about 105 miles. The nearest towns are Huajuquilla, in the State of Chihuahua, about 125 miles due west, and Cuatro Cienegas, in the State of Coahuila, 112 miles to the eastward. Between these points and the town of Sierra Mojada, and to the north of this town, the country is an immense desert, entirely uncultivated, almost uninhabited, and very little known. This

Jan 1, 1887

By Pefer F. Stacey

This paper considers some of the trends in slope design technology that are emerging as we approach the 21st Century. While the ability to design stable slopes has unproved greatly over the past 20 years, trends towards steep short-term slopes for small highgrade orebodies, and very high slopes for mega-pits centered on low grade deposits are starting to indicate limitations in available technology.

Jan 1, 1994

By J. S. C. Joubert

The Koidu Kimberlite Project is situated in the Kono District of Sierra Leone, approximately 330 km east of the capital city, Freetown. The mining lease area is 4 km2 and comprises 2 kimberlite pipes, 4 dyke zones and a number of blows off the dykes. Koidu Holdings established on the property and began dewatering and the removal of silt from the existing 30 m excavation of the No.1 Pipe in 2003. While the original planning for the pipes included conventional open pit operations, mitigating factors such as the proximity of the town, the presence of houses close to the perimeter of the pipe, the size of the pipe and the planned open pit depth with relevant stripping ratios, as well as uncertainties on the grades in respect of an underground operation, lent itself to the vertical pit concept. The vertical pit was established using an A-frame headgear for the hoisting arrangement, with sidewall support comprising a combination of 20 m and 40 m long cable anchors, rock bolts, wire mesh and pneumatically applied concrete. The pit reached steady state production in January 2007 and produced some 26,000 tonnes of head feed per month until August 2007 when mining reached a depth of 74 m below the pit collar (approximately 126 m below surface). Mining was suspended following a sidewall failure that disrupted operations. Now that the grades in No.1 Pipe have been validated, focus has been switched to an underground operation taking account of both No. 1 Pipe and No. 2 Pipe. While the mining costs for the vertical pit have been higher than for a conventional open pit, the concept did circumvent the social implications, the issue of grade consistency and diamond value at depth, as well as providing the time frame to carry out a full underground mining study.

Jan 1, 2008

By O. P. Arora, M. Metzger

Single-phase aluminum containing 1 to 600ppm copper was studied in 7 to 26 pct HCl. The corrosion rate in the autocatalytic stage was resolved into a constant intrinsic component and an acdelerating autocatalytic component, and attention was focused on the part of this stage where the corrosion rate could be described by a simple empirical relation. Autocatalytic corrosion in this period was localized and its rate increased rapidly with copper content and with the strength and chlaride content of the acid. The effects of adding cupric ion to 16 pct HCI were functionally and quantitatively inconsistent with the autocatalytic rates observed. A theory of these rates was given based on the deposition in nzetallic contact with the aluminum of part of the copper introduced by corrosion. It has long been known in a general way that aluminum containing sufficient copper suffers in hydrochloric acid an autocatalytic acceleration of corrosion resulting from the introduction into the acid of copper ions and their reduction on the specimen as elemental copper, which provides cathodes of low hydrogen overvoltage.'-3 In a previous paper, this phenomenon was identified in single-phase high-purity material at copper levels as low as 20 ppm and an empirical equation describing autocatalytic corrosion rates in 16 and 20 pct HC1 was presented. In the present work the range of acid strength and chemistry studied was extended, a more accurate empirical equation for the autocatalytic rate was determined, and a theory of this rate was formulated. A major source of interest in this system is the intergranular corrosion, which is also strongly influenced by copper content,= and an objective of the present work on general corrosion was to provide a basis for studying the role of copper content in intergranular corrosion, which is experimentally much less accessible.

Jan 1, 1963

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By Alden B. Greninger, Victor G. Mooradian

Microscopic examinations of quenched (beta) 60:40 copper-zinc and quenched (beta) 74:26 copper-tin alloys have frequently disclosed long, thin parallel bands or markings within the polyhedral beta grains. Apparently, it has been accepted that these markings are mechanical twin bands, although there is no published account of experimental data that might tend to substantiate this belief for the copper-zinc system, and only meager evidence has been submitted for the copper-tin system. Johnsonl0 commented upon the markings he observed after deforming a quenched brass of 55.6 per cent copper and 44.4 per cent zinc. Clark's papers4 on the heat-treatment of Muntz metal contain many photomicrographs of markings in beta brass; these she referred to as Neumann bands (inasmuch as repolishing and re-etching failed to remove them) and stated that markings present in Muntz metal as quenched were the result of shock imparted during the polishing operation. Van Wert18 first suggested that these parallel markings in quenched beta brass (60:40) might be alpha precipitated along certain crystallographic planes of the matrix lattice. He showed that upon reheating the specimens to temperatures below 800" C., obvious precipitation of alpha within the large beta grains first occurred at the markings. In a discussion of this paper, Phillips stated (pp. 505-507) that in his opinion the markings observed by Van Wert were mechanical twins resulting from contraction strains produced during the quenching operation. In a study of segregate structures in beta copper-tin, Smith17 observed that in the quenched beta phase (containing 74.92 per cent Cu) parallel . bands or markings very similar to those in metastable beta brass could be

Jan 1, 1938

By H. H. Richardson, E. H. Dix

Of all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations would have been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 525" C. to about 1 per cent. at 300" C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540" C., and that this amount decreases to about 3 per cent. at 20" C. In the same year Ohtani and Hemmi3 reported a solubility of 4.8 per cent. copper at 520" C., 2.6 per cent. at 460" C. and 1.5 per cent. at 420" C.

Jan 1, 1926