Search Documents

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

By Peter W. Lotz

Contents of: ?Sampling for Cyanide in Metallurgical Processes? ?Sampling at process level of operation ?Sampling at environmental level ?Sample stability and integrity issues ?each citing possible objectives, practical example and reasons for surprises Overall recommendations on sampling plans and procedures to maintain sample integrity

Jan 1, 2005

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Pre-reduction of chromite outside the submerged-arc furnace (SAF) can significantly lower the specific power consumption in the SAF process. Conventional processes for the pre-reduction of the ore operate at relatively high temperatures, at 1400-1500°C. It is possible to enhance the rate of reduction at low temperatures by optimizing the flow rate of inert gas over the reaction site. The influence of the flow rate of inert gas on the rate of reduction of chromite ore was investigated. The rate of reduction initially decreased wit the flow rate of the gas. It increased subsequently at higher flow rates to be followed by a decrease again. There was an optimum flow rate at which maximum reduction could be obtained. It was possible to achieve high levels of reduction at 1200°C by optimising the flow rate of the gas. The degree of reduction obtained was comparable to that obtained at 1400-1500°C, by conventional process routes.

Jan 1, 2007

By J. D. Doll

MSHA has promulgated a rule to limit the exposure of underground metal/nonmetal miners to diesel particulate matter (DPM). In May 2008, the final personal exposure limit will be lowered to 160 µg/m3 total carbon. To comply with this rule, mine operators are implementing a variety of control technologies. In this study two types of control technologies (ventilation and cabs) which are being implemented in limestone mines were investigated. Two stone mines in this study use large diameter propeller fans for main mine ventilation and direct the air to the faces using auxiliary fans, stoppings, and long pillars while bypassing the old mine workings. NIOSH measured for sub-micrometer elemental carbon (EC) using SKC DPM cassettes (analyzed using NIOSH 5040) and a near real time instrument. With the present ventilation and the number and type of vehicles used, the concentration of EC from DPM at the working areas was at or below 400 µg/m3 for both mines and about 166 µg/m3 and 251 µg/m3 at the returns. The real time data showed that the ventilation was reaching the working areas and effectively diluting the DPM. Environmental cabs were also used to reduce DPM exposures in three underground limestone mines. Using NIOSH method 5040 and near real time EC instrumentation, NIOSH sampled inside and outside of a loader cab at one of these limestone mines to determine the effectiveness of the cab. The cab was found to be over 90% effective in removing DPM as long as the cab system was properly maintained, and doors and windows were closed.

Jan 1, 2009

Jan 1, 1967

By S. Achilleoudes

This paper describes the various factors that contribute to the maximum design pressures acting on box fronts and how these factors influence the mass and economy of box front steelwork. The influence of material density, rock size and moisture content on the incidence of hang ups and mud rushes in the rock pass is also highlighted. The loads acting on any box front are a function of several different parameters. These include natural, operational and excavational parameters. A case study analysis was carried out using UG2 ore and a typical box front structure to demonstrate the relationship between the mass of the box front and the material pressures resulting from variations in the above parameters. Based on the results of this case study, the required design mass of a side mounted box front for a rock pass containing platinumUG2 increases in (close to) linear proportion to % overbreak and is also linearly proportional to the pressure on the face of the box front beyond saturated conditions. The mass of the box front structure also doubles with a 100%increase in over-break which emphasises that a box hole excavation that is as neat as possible will yield a lighter and more econimical box front structure.

Jan 1, 2005

By T. Sakaguehi

Some attempts were made to recover and remove of uranium that may be present in refining effluents, mine waste Water, and other waste sources by using microbial biomass. To establish which microorganisms accumulate the most uranium, 135 species of microorganisms (42 bacteria, 26 yeasts, 34 fungi and 33 actinomycetes) were screened. Of these 135 species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stuzeri, Neurospora sitophila, Streptomyces albus and Streptomvces viridochromogenes. In addition to the research on uranium uptake, thorium recovery by using microorganisms was investigated. High abilities were found in Streptomyces levoris and Bacillus subtilis. The selective accumulation of heavy metal ions by various microorganisms has also been examined. Uranyl, mercury and lead ions were readily accumulated by almost all of the species of microorganisms tested. Actinomycetes and fungi differ from many bacteria and most yeasts in their selective accumulation of uranium, and mercury. The basic features of uranium uptake by Streptomyces viridochromogenes, a microorganisms with high uranium-uptake ability, were investigated systematically. Synthesizing these results, we suggested that the accumulation of uranium into these microbial cells is not directly mediated by any metabolic process:, but almost completely dependent upon physicochemical adsorption on the cell components. In addition to this fundamental research, uranium recovery was investigated in immobilized Streptomyces viridochromogenes. These immobilized cells adsorbed, uranium readily and selectively. The immobilized cells recovered uranium almost quantitatively and almost all uranium adsorbed was desorbed with 0.1 N Na2CO3, These results showed that microbial cells are more stable after Immobilization and can be used repeatedly for the process of uranium adsorption-desorption. These results suggested that these microbial cells can be used for the recovery and removal of nuclear fuel elements, such as uranium and thorium, from refining effluents and mine waste water.

Jan 1, 1991

By W. R. Crane

Subsidence and ground movement are phenomena common to and attendant upon practically all large-scale mining operations, and under certain conditions may occur in all workings, large and small. The interpretation of the cause of failure in rock masses involves a study of the nature of plants of weakness common to all rocks. The dominating planes of weakness can readily be determined by observation in any given locality, and in order of importance in the study of subsidence are (1) faulting planes, (2) bedding planes, (3) joint planes, and (4) other prominent planes of weakness such as thrust and shear planes and contacts. This report has mainly to do with the third item, joint planes, and is a preliminary statement which t to be followed by a more complete report in bulletin form.

Jan 1, 1931

By H. Y. Sohn, S. PalDey

"A new chemical synthesis process for the preparation of intermetallic compounds has been developed. It involves the vapor-phase reduction of mixtures of constituent metal chlorides by magnesium vapor to produce intermetallic compounds in the form of fine powder. The advantages of the process include (a) the use of inexpensive raw materials, (b) low reaction temperatures, and (c) products in the form of fine particles. Titanium and nickel aluminides were prepared by this method. The effect of AlCl/TiCl3 partial pressure ratio on the formation of different titanium aluminides was studied. A two-phase mixture containing 80 mol % of TiAl and 20 mol % of TiA13 formed at an AlC13/TiC13 ratio of 10. The amount of TiA13 was maximized to 72 mol% at an AlC13/TiC13 ratio of 16. The maximum conversion of the limiting chloride TiCl3 was 94 % . In the case of nickel aluminides, NiAI, NiAl3, and Ni2Al3 were formed by reducing mixtures of NiC12 and A1Cl3 vapors. The effect of the partial pressure ratios AlCl3/NiC12 and Mg/NiC12 on the formation of nickel aluminides was studied. The maximum content of NiAl obtained was 98 mol % . At the AlC13/NiC12 ratio of 19, a two-phase mixture of 17 mol% of NiAl and 83 mol% of NiA13 was produced. The product particles were very fine in the size range of 0.05 to 0.2 µm.A. IntroductionIntermetallic compounds are attracting much attention [1]. Titanium and nickel aluminides have attracted a great deal of attention from the aerospace as well as automobile industries because of their potential for high-temperature application (e.g., low density, good oxidation resistance, and high-temperature strength retention [2, 3]). Gamma TiAl and two-phase (TiAl and Ti3Al) alloys [4] are used for gas turbine engine rotational components as well as automobile exhaust valves. TiAl3 is one of the most extensively investigated aluminum-rich intermetallics. Nickel aluminides are attractive because of their low densities, relatively high melting point and good high-temperature strength properties. For example, Ni3Al shows increasing rather than decreasing yield strength with increasing temperature [5]."

Jan 1, 1998

By T. McKeon

Gravity separators are commonly used in multistage cleaning and scavenging circuits to improve the quality and/or recovery of the final concentrate. Unfortunately, studies suggest that many industrial plants are poorly designed in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiencies of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Jan 1, 2005

By Avery H. Reed

RECORD production of cement, clays, salt, sand and gravel, and stone highlighted the mineral industry of the State in 1956. Coal and iron-ore production declined owing to increased imports of foreign iron ore and decreased demand for metallurgical coke. Alabama ranked second in production of bauxite and of native asphalt, and third in output of iron ore. New developments in the State included the Citronelle oilfield and its 97 wells, which more than doubled the total production of petroleum compared with 1955. There is no question about the impetus that field has given to the oil and gas industry in Alabama, now 13 years old. The State's 4 oilfields are in southwest Alabama and its 1 gasfield is in Marion County, in the Warrior coal basin.

Jan 1, 1958

By Susanna G. de Jager, Francis W. Petersen

"To enable the prediction of reagents suitable for fine coal flotation, it is necessary to develop a methodology applicable to different South African coal types. Statistical confirmation of the applicability of this methodology is important to avoid recommendation of reagents on a trial and error basis.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements. Flotation tests were used to validate expectations from the characterisation of the coal samples.RESULTSThe flotation data indicated that all of the coal samples were amendable to froth flotation. The best results were obtained with the Witbank seam 2 coal and the poorest flotation with Syferfontein seam 5 coal. The flotation tests showed that the best reagents to float all of the coal samples studied were iso-decanol and dodecene. These reagents produced flotation products that were near to the release curve, which are the optimum flotation results (obtained when using iso-paraffin as collector). Dodecene resulted in low ash products and iso-decanol in high yield products."

Jan 1, 2003

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By W E. Short

Ausmelt top submerged lance technology is at the cutting edge of technological developments in non-ferrous metal smelting with commercial operations throughout the world. The Technology is being used for lead smelting, copper smelting and matte converting, fuming zinc from slags, recycling iron residue from zinc plants, processing the aluminium industry hazardous waste SPL , precious metal processing, nickel-copper residue smelting and converting, and tin smelting. The Technology is also being developed for projects involving iron-making and waste industry opportunities. There are 19 furnaces operable or under design at the time of writing. The benefits to operators using Ausmelt Technology vary depending on application, but typically result from environmental improvements, enhanced recovery of valuable products, lower capital and operating costs, more flexible operations capable of handling a wide range of feed materials, better removal of impurities, or improved product quality. Growing industry acceptance of the Technology is evidenced by the fact that more than 20 per cent of the worldÆs tin production will be extracted in systems using Ausmelt Technology when the Yunnan Tin Corporation plant starts up in 2001. Metallurgists, industrialists and investors have accepted the Technology for improved operations in both greenfield main smelters and add-on plants in Korea, China, Japan, Germany, Peru, Zimbabwe, India, Namibia and Australia. Ausmelt intends that this paper will update the industry by outlining recent achievements of the Technology in global metallurgical operations.

Jan 1, 2000

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By Rex E. Loesby

The dramatic increase in molybdenum prices from the low of less than $2.50/lb in 1999 to more than $40/lb in 2005 has caught the attention of molybdenum mine owners and exploration project developers. Between 2005 and early 2007, prices pulled back and stabilized within a trading range of $25/lb to $30/lb. This 1,000 percent price increase has motivated most existing producers to expand production and is motivating those with molybdenum prospects to accelerate the development process for earliest possible production. It is still unknown how much new production will come from existing mines, how much production will be needed from new mines if demand continues to grow and how many potential new mines might be available to meet future demand. And of course, the billion dollar question is whether molybdenum prices will remain high, or will they fall back to the low levels seen during the 1980s and 1990s? This article attempts to answer these questions in a way that will help molybdenum project developers and financiers plan for the future.

Jan 1, 2007