Search Documents

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By U. Richter

Conveyors are a highly effective means of transporting material over long distances. Recently there has been a trend toward long conveyor systems with high capacity single flights. These conveyor systems are an efficient alternative to costly truck fleets. Also with deeper mines, the use of diesel driven trucks becomes more difficult. Another trend is in underground mining, where conveyors are an efficient alternative to drift hoists or dedicated rail systems.

Jan 1, 2012

By C. Ware, R. Uken, G. Whitmore

The coastal dune cordon of northern KwaZulu-Natal is among the highest in the world reaching heights in excess of 180 m and up to 2 km in width. It comprises a complex system of Quaternary stacked dunes of various geomorphologies, types and ages (Sudan, 1999; Maud and Botha, 2002;Ware et al., 2001; Ware, 2003). The dunes contain economic heavy minerals that have been exploited for the last two and a half decades. Dune units have recently been defined based on sand composition and texture(Sudan, 1999; Ware, 2003). Despite this, little work has been undertaken on the clay-fraction (< 2 um). This work documents the weathering of dunes to form clays. From the documented clay assemblages and relative abundances, a simplified weathering sequence with increasing maturity can be summarized as follows: primary minerals ? illite + vermiculite ?illite +interstratifications ?illite + montmorillonite ?halloysite + interstratifications + kaolinite ?kaolinite. The dominant controlling factors in determining clay assemblages is pH and leaching conditions. The presence of carbonates results in an alkaline pH and high concentrations of Ca2+and Mg2+which favours the formation of montmorillonite and vermiculite. However, vermiculite tends to form under slightly acidic conditions and is indicative of palaeosols where organic acids produce localized acidic pH’s. In contrast to this, kaolinite will only form and concentrate when carbonates have been leached. Kaolinite dominated samples are considered very mature under current climatic conditions(Chamley, 1989). Halloysite represents a transitional phase between montmorillonite and kaolinite (Herbillon et al., 1981). Ion mobility and evacuation is also critical in determining clay assemblages. Past work and field studies indicate that the dune cordon acts as an open system, resulting in carbonates and mobile ions being readily leached and lost from the system. However, when prolonged weathering has caused an accumulation of fine-grained material, the permeability decreases substantially whereby mobile cations and silica cannot be readily evacuated. This results in the formation of montmorillonite rather than kaolinite, even when carbonates have been leached. Illite (sericite) is considered to alter directly from feldspars. However, dune stacking and geometries, vegetation, water fluxes, reworking and erosion complicates this sequence.

Jan 1, 2003

By V. Eloy Román

El presente trabajo evalúa la adición del oxígeno puro al circuito de cianuración, con la finalidad de incrementar el porcentaje de recuperación de oro y plata, así como su efecto sobre el consumo de cianuro de sodio. En ese sentido, la mayoría de las plantas mantienen un alto nivel de concentración de cianuro, en lugar de un alto nivel de oxígeno disuelto en la solución. Como consecuencia de ello , operan a niveles de cianuro de modo que la disolución del oro depende del nivel de oxigeno disuelto. Por ello, es más fácil mantener un nivel alto de cianuro, que un nivel alto de oxígeno disuelto en la solución, principalmente si se utiliza aire en lugar de oxígeno.

Sep 12, 2005

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By K. G. Stowe

"1. Introduction Mattagami Lake Mines and Orchan Mines operate zinc copper mines adjacent to one another near Matagami, Quebec, situated approximately 300 kilometres north-east of Rouyn-Noranda. (Note: Mattagami Lake and Orchan are in the process of being absorbed by Noranda Mines and will become Noranda Mines-Matagami Division). Both concentrators began operations in late 1963.The Mattagami Lake concentrator is capable of treating up to 3,500 metric tons per day of massive sulphide ore with a mineral composition shown in TABLE 1. The Orchan concentrator consists of two separate circuits - the Orchan circuit with a capacity of 1,050 metric tons per day and a custom circuit with a capacity of 825 metric tons per day. Throughout its operation, Orchan has custom milled ore from several smaller deposits in the Matagami district."

Jan 1, 1979

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

Over the past few years, there has been an emerging relationship between business and civil society, especially NGOs. This relationship has the potential to bring about significant change, identifying common ground between commercial and societal interests. The mining industry has been a leader in acknowledging the need for community consultation and engagement. This paper argues that partnerships can make a very significant contribution to the industry as it comes to terms with the dilemma of an open economic system pushing against a closed ecological system.The paper will pose a number of questions: where is the locus for debate about sustainability in the mining sector?; how well embedded within companies are the new competencies that Leon Davis first identified in 1995 for the mining sector?; how has education for mining engineers or exploration geologists changed to prepare people for what are very different expectations within the working environment?; how well is the industry doing in managing its own environmental impact and what is its responsibility to an agenda for sustainability which extends beyond its own operations?;and how can NGO partnerships contribute to more sustainable outcomes? The paper does not aim to answer these questions, but to explore them in the hope that the issues and possibilities raised will contribute to advancing progress towards sustainability within the industry.

Jan 1, 2002

By D. Norval, J. J. Dunkley

The process of atomisation is introduced and related to granulation. Some processes applicable to ferroalloys are discussed, along with their limitations and advantages. Examples of applications of atomisation to the processing of ferroalloys, including ferrosilicon and ferromanganese for use in the welding industry and as injectable additions to steel or cast iron are also presented. The economics of the process and the impact of process scale are discussed, along with criteria for process selection and system design.

Jan 1, 2004

By Dan Armour

Bolting solutions traditionally offered only wet drilling or dry drilling options; each with advantages and disadvantages. Joy Mining Machinery has developed a Mist Drilling System that incorporates the best of both types of drilling. Compared to wet drilling, mist drilling offers as much as a 90% reduction in water use. As a result, floor and roof conditions are tremendously improved. This offers a safer and more comfortable work environment for operators. Mist drilling can offer a significant reduction in noise levels compared to dry drilling and in recent trials, bit life has been greatly improved. Holes are cleaner and operators experience less exposure to respirable dust.

Jan 1, 2005

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008

By Russell Carter, Tom Barkley

"Optimization of blasting is hampered by the lack of inexpensive methods of measuringblast results. Optical methods of size analysis have the potential of creating abreakthrough in size analysis and in overall blast optimization. Attainment of reliablemeasurements hinge on solving a number of shortcomings inherent to optical systems."

Jan 1, 1999

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

By Roland Oliver

Detonators or blasting caps are made in several different grades of strength, because some powders require not only a greater, but a different initial detonation than others to convey their maximum energy through a whole charge, and the detonating qualities of each powder vary with changes in its physical condition––whether it be warm or cold, rigid, plastic, homogenous or otherwise.

Jan 1, 2007

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986