Search Documents

By J. H. Potgieter

This paper describes two cases of corrosion that occurred in dry-process, rotary, cement-clinker kilns. In the case of the kiln with five pre-heater stages, the attack occurred primarily from sulphates that probably originated in the raw feed and fuel being used in the plant and that penetrated the refractory lining. The corrosion was similar to ash-deposit corrosion often observed in steam boilers. In the second case the plant consisted of a long dry kiln with a single pre-heater fitted to the feed-end. In this case the corrosion could be ascribed to alkali chloride penetration through the refractory-brick lining and subsequent hot corrosion of the kiln shell.

Jan 1, 2004

Zincor operates four Lurgi fluidized-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Roaster 3 was the first to be rebuilt in 2006 because its condition had deteriorated the most. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled owing to the combined effects of excessively high operating temperatures and corrosion. These were caused by the following two main factors: ?Thicker external insulation was installed during a previous maintenance shut, which resulted in an increased steel shell temperature and exacerbated the normal metal fatigue ?SO2/SO3 containing gas that had permeated the brick lining passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but when it was dismantled more damage was found, and the roaster was rebuilding from the tuyeres upwards. During there building the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

By Richard Mainiero

In any construction project involving explosives, care must be taken to protect workers from carbon monoxide (CO) generated by blasting operations. CO is an odorless, colorless gas that can cause illness and death by asphyxiation. In general, the first symptoms include headache, fatigue and lightheadedness. At higher exposures to CO, skin flushing, rapid heart rate, and lowered blood pressure occur. At ever, higher exposure levels, decreased attention span is followed by nausea, vomiting, unpaired coordination, fainting, coma, convulsions and, finally, death. The detonation of explosives in blasting operations generates a range of toxic fumes, but CO is the most insidious because it is colorless, odor less, and is long lasting, since it is not readily removed try reaction with ground water, soil or rock. Additionally CO is generated in relatively large quantities compared to other toxic: fumes. CO may continue to seep out of blasted material long after the odor commonly associated with detonated explosives has dissipated. It is never safe to assume as confined space in the vicinity of a blast is clear of toxic fumes. CO may be present even if the area looks Clear and many hours have passed since the last blast.

Jan 1, 2000

By C M. Evans, D Thomas

Solid EnergyÆs Wangaloa open cast coal mine was operated between 1945 - 1989, and remained closed and disused until 2001 when SENZ initiated a mine rehabilitation programme. It is nearing the final stages of physical and environmental rehabilitation, aimed at creating an aesthetically pleasing and useful landscape. The final goals of these efforts are to produce an area, which has recreational and educational value. SENZÆs holistic approach to rehabilitation has been undertaken, treating the entire historical mine footprint instead of focusing only on those disturbed areas and the minimum range of issues just to meet with legal compliance. Rehabilitation at the site has included overburden modification with an emphasis on stability, removal and replacement of unhealthy and invasive plant species, and an AgLime amendment to alter soil pH conditions, which would support native plant species. To date, most ongoing activities relate to final planting and plant upkeep, and maintenance of the landform including ongoing erosion control, pest control, environmental monitoring, and research. Environmental quality concerns at the site may be treated by using a combination of methods, including regrading and capping of acid-generating pyrites, soil treatment with AgLime, and passive wetland treatment within existing water courses. Following major works, the mine site area may be opened to the public for recreational activities, interpretive displays on historical mining activities, and observation and appreciation for otherwise unseen geological features. SENZÆs holistic approach to reclamation, rather than treating minor issues, will result in the former mine site being transformed into an asset and the environmental and financial liability associated with the closed mine being discharged. Former mine sites can be turned from environmental liabilities with no recreational or public value (and potentially dangerous to life) into sites that can be safely used by the public for recreational and educational purposes.

Jan 1, 2006

By Rob Boom, Yasuyuki Tozaki, Frank M. Wheeler

Selection of a suitable site for a metallurgical plant is crucial for the success of the business case. For a brownfield project, with the decision to locate the project on a site with existing production facilities and activities, the selection of the site has been made. For a greenfield project, important economic and logistical considerations include proximity to primary and secondary resources and/or to the market, infrastructure, and access to energy and water. National and regional aspects, including the social license to operate, can be decisive in final site selection. Key to recruiting and retaining a labour force are proximity to urban areas, along with weather and health conditions at the site. Risk factors include site geotechnical parameters and topography, contamination, as well as probability and types of potential natural disasters.

Jan 1, 2015

By Paul D. Tomlingson

An effective maintenance program ensures the adequate availability of production equipment. In turn, this availability enables production to maximize utilization and successfully meet production targets. An overall production strategy is necessary to draw all departments toward this common effort. Only then will production targets be met. From the maintenance view this means that production must comply with PM and repair schedules. Purchasing must supply parts and materials on time. Mine engineering must not overwhelm maintenance with non-vital construction. Accounting must provide correct, timely cost information - - etc. This strategy - - its content, effectiveness and enforcement is the responsibility of the mine manager . . . his alone. This paper describes a successful approach to maintenance within this strategy.

Jan 1, 1979

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

A research project was commissioned by the Australian Coal Association Research Program (ACARP) to improve the understanding of tailgate strata mechanics and to provide a more rigorous engineering basis for tailgate support design. A deformation mechanism termed æskew roofÆ was defined which relates the regional influence of differential horizontal strata movement (shear) about longwall extraction to gateroads. Confirmation of the mechanism was achieved by field investigations which included measurement of the shear displacement along weak interfaces. Under geological and mining conditions where the skew roof mechanism operated, strata units were found to move progressively further towards the goaf with height into the roof. 3D numerical modelling was used to assess the major geotechnical factors controlling the mechanism and to determine appropriate support strategies within a æskew roofÆ environment including the role of cables versus standing supports. The skew mechanism is considered relevant to; all roadways in the vicinity of longwall extraction including the faceline itself, chain pillar design, and support design.

Jan 1, 2005

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Y. Poornachandra Rao, P. C. Sudhakar, L. Malakondaiah

NBV commissioned a 27.6 MVA furnace in the year 2005. This paper explains: a)Furnace design features b)Furnace process control, Direct slag granulation c)Continuous casting, Waste heat recovery, Sintering d) Gas cleaning plant, Protection of Environment. Keywords: Furnace Equipment, SiMn Production, Casting, Heat Recovery and Low hood

Jan 1, 2007

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company's branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By Charles B. Kenaban

The possibility of using ultrasonic energy as a tool to improve the electrolytic deposition of copper and zinc from several electrolytes was investigated by the Federal Bureau of Mines. Sound with frequencies of 20, 26, 38, and 400 kilocycles per second and acoustical intensities of 0.25 to 1.5 watts per square centimeter was employed. Measurements of cell voltage, anode and cathode current efficiencies, and electrode potentials were made at various current densities. Effects of ultrasonics on the quality of the deposit and on anode corrosion also was noted. In the electrolytic recovery of copper from an acid copper sulfate solution at 50° C., adherent, well-consolidated deposits are normally obtained up to a current density of 30 amperes per square foot. As the current density is increased above this value, the deposits normally become progressively more spongy and less adherent. Ultrasonic irradiation resulted in adherent and well-consolidated deposits at current densities up to 300 amperes per square foot. Radiation also produced smaller grain size and preferred orientation of the copper crystals. In addition, radiation caused as much as 3-volt decreases in cell voltages at the higher current densities. These decreases were caused chiefly by depolarization of the anode, although small depolarization effects were also noted at the cathode. Radiation apparently did not greatly affect cathode-current efficiencies, but prevented excessive anode corrosion at the higher current densities and resulted in more uniform corrosion. Ultrasonic radiation at a frequency of 400 kilocycles per second was not as effective as radiation at the lower frequencies. Circulation of the electrolyte at rates up to 5 percent of the cell capacity per minute did not produce results comparable to those effected by ultrasonic radiation. Rapid rotation of the cathode up to 1,800 revolutions per minute gave results approaching those obtained with ultrasonics.

Jan 1, 1961

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By Cleveland Meeting

Jan 1, 1945

By H. I. Kim

The leaching of a complex matte in chlorine and chloride media was studied. The matte was prepared from manganese nodules by the reduction smelting-sulfidation route. From XRD analysis, the major phases of the matte were identified as CuFeS2, CuS2, (FeNi)9S8, (FeNi)S2, Ni9S8, Ni3S2, (CoFeNi)9S8 and Co metal. Investigated were the chlorine, hydrochloric acid, hydrochloric acid-oxygen, ferric chloride, ferric chloride-oxygen, cupric chloride and cupric chloride-oxygen systems. The results are discussed in terms of reagent concentration, retention time, leach temperature and gas sparging rate. The chlorination process resulted >99% metal extraction efficiency within a short retention time and at atmospheric temperature. However, there were no preferential extractions of Cu, Ni and Co with respect to Fe. The cupric chloride-oxygen system produced leach liquors with the lowest Fe content and with a high base-metal extraction. Sulfide sulfur was converted to mixtures of elemental sulfur and sulfate in all the studied systems.

Jan 1, 2009