Search Documents

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003

By B. Friedrich

In a German governmental funded three-year research project, a closed loop recycling process for Nickel-Metalhydride-Batteries (NiMH) is under development. Today the discarded batteries are used in the steel industry as a cheap nickel source. Cobalt and rare earth (RE) are slagged and lost for reuse. The entire value of the metals in discarded Ni-MH is estimated to be 4?-4.5 ?/kg. Spent NiMH-batteries containing 36?42 per cent Ni, 3?4 per cent Co and 8?10 per cent rare rarth (Ce,La, Pr, Nd). The dismantled and processed NiMH-batteries are melted in a DC electric arc furnace producing a nickel-cobalt alloy and a slag phase highly enriched with RE-oxides. The key to success in this process is to find a suitable slag system, which ensures best separation of NiCo-alloy from the rare earth oxides and high concentration of RE in the slag. Different oxidic and halogenic slag systems are investigated in the melting process. So far a slag system based on 65per cent CaF2 and 35 per cent CaO delivers the best separation of the two phases and metal yields. A slag with a composition of 20?25 per cent La, 13-16 per cent Ce, 1.5?2.5 Pr, 4.5?6.5 per cent Nd is obtained and further treated to misch metal hydro-/electrometallurgically. The first results of the influence of rare earth oxides on the density of CaO-CaF2slag system are shown at 1600°C. Keywords: battery recycling, CaF2, CaO, rare earth oxides, slag characterization, density measurement

Jan 1, 2004

The Epithermal and Mesothermal Gold Prospectivity modelling projects carried out by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250,000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, to stimulate mineral exploration and investment in exploration, has been successful with eight new companies acquiring new tenement positions and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were done at a national scale and consequently not all exploration data were compiled into the prospectivity models. Several of the new companies recognised the value of the prospectivity modelling work and committed exploration funds to continue the modelling process. They recognised a need to compile the remaining data and run the models again to allow detailed exploration targeting. Detailed data compilations including digitising historic exploration stream sediment sample, rock chip sample, soil sample and drilling data has been completed. New models have been completed in Otago for mesothermal gold mineralisation and in the Coromandel and Northland for epithermal gold. The new models have been compared with the original regional scale models and used to target prospect scale exploration. This work has allowed exploration models for epithermal and mesothermal mineralisation in New Zealand to be refined. More importantly this work has identified significant areas with potential to host gold mineralisation with little or no systematic geochemical data including soil sampling or drilling. Exploration work programs have been designed to acquire these missing data and exploration funds have now been committed to test the areas highlighted by the prospectivity modelling. In summary, the Epithermal and Mesothermal Gold Prospectivity modelling work has successfully attracted new investment and ideas to the exploration scene in New Zealand. The projects had an estimated cost of NA$250 000 and will in the next two years, just through exploration expenditure, attract more than NZ$10 M in investment. If a mine is discovered the return on investment will be considerably greater.

Jan 1, 2004

By B Kretschmer, G Bartel, B de Villiers, W Watt

"The Nyrstar Port Pirie Smelter, located on the eastern shore of the Upper Spencer Gulf in South Australia 230km north of Adelaide, began operation in 1889 to process lead concentrate from the Broken Hill lead and silver mines. The site still operates an updraft sinter machine, commissioned in 1955, with the product fed into a blast furnace. While sinter plant technology has changed and improved since 1955, development has reached the stage where further enhancements are not possible or economic. High purity lead concentrates command lower margins and for the smelter to remain economically viable a wider range of higher value materials must be treated. The current flowsheet cannot meet this demand. Additionally, community blood lead levels particularly in children below four years of age, are a critical indicator used to measure the site’s environmental performance. The smelter’s environmental licence to operate is dependent on meeting future community and regulatory expectations. To achieve this a major step change in the emission performance of the smelter is required. Since 2008 pre-feasibility work has been undertaken to develop a new flowsheet and business model to allow Port Pirie to operate sustainably into the future. The main requirements were for the smelter to reduce lead and sulfur dioxide emissions that impact on the local environment and community to meet current and future environmental expectations, as well as dramatically reducing current feed constraints and change the business case from a marginal business to a sustainable profitable business. After reviewing all practical options a decision was made to replace the sinter plant with an Outotec Top Submerged Lance (TSL) furnace. This paper describes how the new furnace technology was selected and how it will be integrated into the present flowsheet; the unique funding arrangements that are in place to deliver the redeveloped site; and future opportunities that are associated with the implementation of the new flowsheet. CITATION: De Villiers, B, Bartel, G, Watt, W and Kretschmer, B, 2015. Nyrstar Port Pirie redevelopment, in Proceedings MetPlant 2015, pp 325–337 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 7, 2015

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007

The lignite resource in the southern part of the South Island is New ZealandÆs largest source of indigenous primary energy. The ten deposits evaluated by the Liquid Fuels Trust Board (LFTB) have a total recoverable reserve of 6.2 billion tones equivalent to 74 000 PJ of energy or 20 times the original energy content of the Maui gas field. Updating the economics of the original LFTB studies indicates that lignite could be mined for between NZ$1.0 and 3.0/GJ. Its conversion to synthesis gas for production of petroleum products, chemical methanol, ammonia/urea fertiliser or electricity would be in the national benefit and likely to be commercially economic at todayÆs product prices.

Jan 1, 2005

By S. Dicarlo

"In late 1985, B-zone ore was first processed through the Eldor Mines mill at Rabbit Lake. Extensive modifications had been completed in order to mill this ore. In-plant process development was initiated to tune up the new circuits and concentrated on leaching, solvent extraction, impurity and uranium precipitation and tailing and effluent treatment. This process development effort and the results are described.INTRODUCTIONEldor Mines, a division of Eldorado Resources Limited, operates the Rabbit lake mine-mill complex at Collins Bay on the western shore of Wollaston Lake in northeastern Saskatchewan.The first orebody was discovered in 1968 by Gulf Minerals Canada Limited below a small body of water named Rabbit Lake. Ore from the Rabbit Lake (RL) deposit was first processed through the new mill in June, 1975, with depletion scheduled over the next ten years. Continued exploration in the area led to the discovery of four orebodies in the vicinity of Collins Bay: A-zone (1971), B-zone (1977), D-zone (1978) and Eagle Point (1980). Collins Bay is about ten kilometres from the mill facility.In 1982, Gulf Minerals was acquired by Eldorado Nuclear Ltd., who continued the development effort to bring the B-zone deposit into production. The RL pit was mined out in May, 1984 with stockpiled ore providing mill feed until startup on B-zone ore, which was scheduled for November, 1985."

Jan 1, 1988

By J. M. Font, R. G. Reddy

Jan 1, 2004

By R. H. Grau, R. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing somepractical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers’ exposure to airborne contaminants.

By S. Ganguly, R. Kononov

Carbothermal reduction of manganese oxides and manganese ores in the solid state was studied in hydrogen, helium and argon at different temperatures, ore compositions and carbon to manganese oxide ratios. Wesselsore (South Africa) and two grades of the Groote Eylandt ore (Australia) with different level of impurities were examined. Ores were characterised by XRD, X-ray fluorescence, optical microscopy and scanning electronmicroscopy. Isothermal and temperature programmed carbothermal reduction experiments were conducted in a fixed bed reactor in a vertical tube furnace, with on-line monitoring of gas composition by the CO-CO2 infrared sensor. The reduced samples were characterised by XRD, SEM and LECO analyses. Extent of reduction was calculated using data on the off-gas composition, and LECO carbon and oxygen contents in the reduced sample. Manganese oxides in the ore were reduced to a-Mn and carbides Mn23C6 and Mn7C3 depending on the carbon to ore ratio. The reduction rate of manganese ores in hydrogen was higher than in helium and argon. Key words: Manganese, Carbothermal Reduction, Hydrogen, Argon, Carbon Monoxide, Helium, Kinetics.

Jan 1, 2007

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)'s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By Julián M. Ortiz

Uncertainty quantification of a spatially distributed variable at any scale can be handled through geostatistical simulation. Large computation time, storage, and post-processing of the realizations are required to obtain a final assessment of block uncertainty. Multi-Gaussian kriging is a flexible alternative to simulation. The idea is to compute the conditional distribution of uncertainty after normal score transformation of the original samples. Under the multi-Gaussian assumption, all marginal and conditional distributions are Gaussian, hence fully defined by their mean and variance. The parameters of the conditional distributions are obtained by simple kriging and can be back-transformed to the original units of the variable of interest. An estimate and any summary of uncertainty can be easily retrieved. The main disadvantage of performing multi-Gaussian kriging is that change of support is not straightforward, that is, calculating uncertainty of block grades. We propose a methodology to overcome this limitation by considering a matrix simulation to generate multiple probability fields. Each probability field is used to draw spatially correlated point values from the point-support conditional distributions, and multiple realizations of the average can be obtained. This permits the calculation of the average over the block and its uncertainty. These blocks may correspond to selective mining units or to volumes from longer production periods relevant for engineering decisions. They can even be disjoint blocks, such as when several faces are mined at the same time. POSTMG, a Fortran program to perform these calculations, is described and a case study is provided.

May 1, 2004

Study on a Novel Polymer/Bentonite Compound Adsorbent for Removal of Cu(II) from Aqueous Solution

Sep 13, 2010

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

Whilst the fossil fuel-based power industry moves towards carbon capture and storage (CCS) or so-called 'geosequestration', the minerals industry should adapt to reap the benefits of the new technology. If CCS becomes viable, the door is open to potential key developments in mineral processing. For example, truly continuous steelmaking could at last be realised using natural or manufactured gas combined with generic melt circulation. Iron ore fines would form a thin molten layer moving countercurrent to the gaseous reductant on one side of a melt circulation loop with efficient post-combustion without deleterious effects of slag accumulation on the other. This eliminates oxygen steelmaking because carbon has no access to the circulating molten iron. Steelmaking merely requires addition of the appropriate low level of carbon and in-line impurities removal to meet product specification. Concerning non-ferrous smelting, nothing short of virtually zero gas emission will be acceptable in the future. For dolomite-hosted Zn/Pb sulfide ores, typified by those in the Carpentaria region of Northern Australia, the way forward proposed is sulfur fixation at the mine site employing the highly exothermic reaction of SO2 with dolomite, followed by encapsulation of sulfated dolomite in fused ore slag. This releases enough energy for direct ore smelting to individual metal products. However, without CCS the strategy would be unacceptable because of greenhouse gas emissions. The scheme is advocated for direct ore smelting at McArthur River. As a result, the environmental problems of disposal of flotation tailings are avoided. Also, highly energy intensive ultra-fine grinding is eliminated, as indeed froth flotation itself, with overall very significant energy savings and exceptionally high increases in metals recovery. Zinc and lead recoveries approaching 99 per cent are predicted to be entirely feasible.

Sep 13, 2010

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By P. Fredriksson, S. Seetharaman

In the ladle refining process, the ?FeO?-content of the ladle slag is of great importance in the chemistry as well as the energetics of the process. An optimization of the process requires an accurate knowledge of the thermodynamic activities of ?FeO? in the ladle slags. Due to the discrepancies in the existing data, renewed attempts are being made at the Royal Institute of Technology to generate reliable data for binary, ternary and multi component slags containing ?FeO? at steelmaking temperatures. In order to measure the activities of ?FeO? in the slags, a gas equilibration technique was employed in the present work. The slags, kept in Pt-crucibles, were equilibrated with a CO-CO2-Ar gas mixture and quenched after equilibration. The chemical composition of the slag was analyszed. From a knowledge of the thermodynamics of Fe-Pt system, the ?FeO? activities in the slag could be evaluated. The results of the present studies, together with other literature values, were optimized in the slag software, THERMOSLAG® developed in the Royal Institute of Technology, Sweden. The results of the optimization are presented. Model calculations were performed with the KTH slag software, THERMOSLAG®, by using plant data from OVAKO Steel, Hofors, Sweden. It was found that oxygen estimations in the metal from the ?FeO? analyses of slags, obtained by conventional sampling and analysis methods, where less reliable. Estimation of the oxygen levels utilizing the sulphur partition between the slag and the metal were carried out using the THERMOSLAG® software. Reasonable estimations of the oxygen contents in the metal confirmed that this could be a very useful tool for the plant operator. Keywords: ladle, thermodynamics, slags, ?FeO?, experimentation, modelling, sulphur partition

Jan 1, 2004