Search Documents

By Gustavo Tressia

Neste trabalho estudou-se a influência da classe do metal duro, sendo elas G30 e G20, utilizada para a fabricação de fieiras de trefilação de latão (ASTM C27000), na resistência ao desgate destas ferramentas. A geometria das ferramentas foi mantida a mesma, variando-se apenas o ângulo de entrada em 10, 13 e 15 graus, a fim de se observar alguma influência deste parâmetro. As ferramentas foram avaliadas após a tefilação de 10 toneladas de material. As superfícies de trabalho foram analisadas em Lupa Estereoscópica e Microscópio Eletrônica de Varredura, visando identificar os modos de desgaste predominantes. Em todas as fieiras foram observados riscos sendo estes mais intensos na fieira da classe G30. Em todas ferramentas também foi observado adesão de material trefilado, sendo que maiores quantidade de material aderido foram observadas também na fieira da classe G30. A ocorrência de maior quantidade de riscos foi associada a menor dureza da classe de metal duro e infere-se a menor vida útil desta ferramenta.

Jul 30, 2018

By Eun-young Kim

Electrogenerated chlorine leaching of waste printed circuit boards was investigated in hydrochloric acid solutions. The pulverized printed circuit board contained about 37.6% of metal component, in which copper was about 83.6%. The leaching rate of copper was greatly affected by current density and agitation speed. The leaching of copper up to 98% was achieved at 20 mA/cm2, 50?, 180 minutes, and 600 rpm in 1M HCl solution. Increasing agitation and lowering current density enhanced utilization efficiency of electrogenerated chlorine. Leaching of copper was suppressed at initial stage, while the minor metal elements, such as aluminum, lead, and tin, were dominantly leached out.

Jan 1, 2006

By D. M. Weinberg, S. R. Novascone, R. R. Reynolds, J. H. Cole, C. D. Christensen

The mechanical properties of the rocks surrounding an orbital vibrator alter the shape and amplitude of the vibrator’s orbit. Detecting these changes with driving point impedance measurements promises to reveal fractures and, possibly, identify the in situ stress state and significantly increase the depth that can be investigated. Our research emphasis has been on detecting vertical fractures through casing. Experimental and numerical results to date indicate that our new logging tool has excellent potential for determining both the vertical extent and azimuthal orientation of such fractures. Fracture and in situ stress orientations are useful in mine planning.

Jan 1, 2002

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detail on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research,

Jan 1, 1966

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detail on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research,

Jan 1, 1966

Fossil fuel consumption in the United States increased markedly over recent years, and future demands expect to be even greater. Coal, this Nation's most plentiful natural fossil fuel, will play a key role in fulfilling these demands. With expectations of increased coal exploitation, the U. S. Bureau of Mines authorized this project, the objectives of whi.ch were to prepare an authoritative report on current surface coal mining technology, to define current problems and possible solutions, and to project future developments necessary to assure adequate surfaced mined coal production to meet the Nation's future energy needs. These objectives we're accomplished by an extensive review of available published literature and data gathering field visits to active surface coal mines throughout the country.

Jan 1, 1975

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By Satyam Tiwari, Sarat Kumar Das

Tailings from mines and industries impose danger to the environment as evidenced by the recent failures of tailing storage dams. The tailings are mostly non-plastic with silt-size particles, but their behavior is largely dependent on the extreme void ratios of the material. Hence, the critical state provides an appropriate perspective in explaining the behavior of these geomaterials. Based on a comprehensive dataset of non-plastic tailings and non-plastic soils, an attempt has been made here to correlate critical state parameters to extreme void ratios and stress parameters. A hybrid algorithm with multi-objective feature selection (MOFS) and extreme learning machine (ELM) was used to establish the correlation and to identify the most influential input parameters. Based on the information from the proposed hybrid algorithm, a comprehensive prediction model is proposed using multi-gene genetic programming (MGGP) algorithm to facilitate quick estimation of critical state parameters. The performance of both models has been assessed using several performance metrics. The results from the study indicate that hybrid MOFS algorithms perform very well in the prediction of critical state line parameters and the identification of influential features. The findings of the study have significant implications for future research on the safe management of tailing storage facilities.

Dec 22, 2023

By G. J. van Tonder

The use of Molecular Recognition Technology (MRT), a highly selective separation technology using specifically designed ligands (such as macrocycles), has been demonstrated to be an effective treatment process for removal of several ions that are commonly found in many hydrometallurgical circuits as well as in environ-mental treatment operations. Ions removed by MRT include base, heavy and transition metals, precious metals, halides, and alkali/alkaline earths. A MRT pilot plant run was conducted at Zincor to demonstrate the cobalt/nickel purification of zinc electrolyte, and to recover saleable pure cobalt/nickel sulphate solution. The MRT process holds various advantages, which include the elimination of a catalyst such as arsenic trioxide, conventionally used in cobalt and nickel cementation. SuperLig® 138 can be used to remove cobalt and nickel from120?170 g/l Zn-solutions at pH 1?2. The Zincor MRT application demonstrated its capability of concentrating large volumes o copper barren impure solution at low cobalt and nickel concentration levels in the feed, to small solution volumes at high cobalt and nickel concentrations. Around 99.5% of the cobalt was removed from solution with cobalt impurity levels in feed varying between 10 mg/l and 26 mg/l.

Jan 1, 2002

By K. Morsi

Carbon nanotube (CNT) reinforced metallic composites have been recently generating significant scientific interest, due to their expected superior properties compared with other composites. Out of the metallic matrices investigated for reinforcement with CNTs, aluminum has received considerable attention. A major problem has been the dispersion of CNTs in metallic matrices. This paper discusses preliminary results on the mechanical dispersion of CNTs in aluminum powder, powder processing, stability and characterization of aluminum dispersed with CNTs at reinforcement levels equal to and below 5 wt.%.

Jan 1, 2009

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

Uranium exploration over a wide area of the Southern Frame Embayment, South Australia, has defined a number of Lower Tertiary fluvial palaeochannels incised in older rocks. The buried channels contain similar stratigraphicsequences of interbedded sand, silt, and clay, probably derived from the adjacent uranium-rich Olarv Provinee. Uranium mineralization is pervasive within two major palaeochannels, and four small uranium deposits have been found in the basal sands of these channel sequences, at the margins of extensive tongues of limonitic sand.One of the channels is examined in detail with respect to channel morphology, stratigraphy, and rock alteration and the geology and ore controls of the contained uranium deposits are described.A geochemical zonation reflected by variation in limonite, pyrite, carbon, and humic malleI' is defined across one of the deposits. A genetic model is proposed suggesting formation by a uraniferous geochemical cell which migrated down the stream gradient and concentrated uranium on its lateral margins adjacent to the channel bank.

Jan 1, 1978

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

By Heloíza Döering Gasparin

Os efeitos de elevadas temperaturas e do tempo de exposição sobre as propriedades mecânicas de um ferro fundido cinzento hipoeutético foram avaliados em amostras de dois ferros fundidos da classe FC300, de mesma base, com diferentes percentuais de molibdênio. Ensaios de tração até ruptura a quente foram realizados em corpos de prova com diâmetro de 10 mm, usinados de um pino bruto de 30 mm de diâmetro. Os ensaios foram realizados a frio (temperatura ambiente) e a quente (200°C, 300°C, 350°C, 400°C, 450°C, 500°C e 550°C). Os tempos de exposição a elevadas temperaturas, após homogeneização térmica do material, foram de 0, 60, 90 e 120 minutos. As amostras com maior percentual de molibdênio (0,27% em peso) apresentaram melhores propriedades mecânicas para todas as condições ensaiadas. De acordo com a literatura a redução na resistência mecânica com a elevação da temperatura é atribuída à ocorrência de decomposição da perlita, como resultado da difusão do carbono vindo da cementita às lamelas de grafita, que é o responsável pelo aumento da quantidade de grafita no material. As análises metalográficas evidenciam a ocorrência deste fenômeno. Aumentos no tempo de exposição a temperaturas elevadas também contribuíram para a degeneração da perlita.

Aug 7, 2018

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

By W. L. Dare

This information circular is one of a series published by the Federal Bureau of Mines in which the methods and costs of producing uranium ore on the Colorado Plateau are discussed. This report describes the three largest company-operated uranium mines of Climax Uranium Co. - the G-1, the Mineral Joe, and the Frank No. 1. Climax Uranium Co., a subsidiary of American Metal Climax, Inc., was [corporated] May 11, 1950, just 2 years after establishment of the domestic uranium program by the Atomic Energy Commission. Twenty-five years earlier Arthur H. Bunker, now chairman of the board, American Metal Climax, Inc., organized and operated the U. S. Vanadium Co. at Rifle, Colo.3/ Soon after Climax Uranium Co. was organized, it entered into a contract with the Federal Government to build a uranium-vanadium processing mill in Grand Junction, Colo. Under the contract Climax leased from the Federal Government certain uranium-bearing lands that had been withdrawn from public entry in 1948. From Minerals, Engineering Co. on June 12, 1950, Climax acquired other uranium-vanadium properties on Calamity, Outlaw, and Monogram Mesas in Colorado and on Polar Mesa and in the Yellow Cat area of Utah. To house the milling equipment, Climax leased the old Grand Junction sugarmill building of the Holly Sugar Co. Milling facilities, based on a then new process developed for treating both uranium and vanadium, were completed, and the plant went into production in 1951.

Jan 1, 1959