Search Documents

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By Christina Dahnér, Kristina Jonsson, Savka Dineva

The iron-ore underground Kiirunavaara mine (Sweden) has been seismically active since 2008. In 2021 the production is on levels 1079 and 1108 m, at the deepest. The seismic activity has changed in character over time with one step change in 2015 when the number of large (ML>2) seismic events increased, and another one when the mine experienced a seismic event with Mw 4.2 in 2020. In 2017, the mine evaluated Hydraulic Fracturing (HF) as a possible mitigation technique for larger seismic events and a one-hole trial was performed. The trial proved promising, and it was decided to go forward with a large-scale trial covering an entire production area in the mine. The large-scale trial consists of 25 fracturing holes, 50 – 100 m long, running along 500 m out of the ~4500 m long orebody and spanning between production levels 1108 m and 1252 m. The fracturing process continued for a year, resulting in ~38,000 seismic events with −3.3<ML<1.4. The breakdown pressure varied between fractures in the same hole as well as between holes in the same area. Average breakdown pressure per hole was between 12 MPa and 50 MPa. The seismic response to HF in 2021 varied greatly from hole to hole and between fractures in the same hole. The variation in response could be related to the geological conditions and the infrastructure, such as large caving ore passes. In this paper some details about the experiments and broad preliminary analysis of the effect of the HF by using seismic source parameters of the induced seismic events are presented: 1) Distribution of seismic activity, 2) the ‘equivalent’ magnitudes for each hole calculated from the cumulative seismic energy and seismic potency released during the fracturing, compared with the local geological conditions; 3) the predominant failure mechanism of the seismic events caused by HF was defined. A difference in the behaviour between larger and smaller events was noticed, as ML>0 events seem to be compression type failures and ML<0 events seem to be related to slip on pre-existing structures. No seismic events related to creation of a new fracture have been identified yet.

Apr 26, 2022

By H Cifuentes, D J. Williams

Despite the recognised importance of tailings management, there remain little data on the potential benefits of biological treatments compared with physical and chemical treatments. The operation of the majority of tailings storage facilities (TSFs) continues to employ mainly physical solutions, such as sub-aerial tailings slurry deposition, with increasing adoption of thickening, paste and filtration to dewater the tailings involving the addition of chemicals such as flocculants and coagulants. However, with tailings production continuing to escalate rapidly due to the increasing demand for commodities and reducing ore grades, available technologies have not demonstrated cost-effective performance at high tailings production rates. This paper examines the emerging role of bacteria to better manage tailings, reducing risks and optimising storage capacity. Bacteria have the potential to enhance tailings dewatering, maintain their permeability, delay the onset of desiccation cracking, and improve their shear strength. Bacteria-treated tailings may be suitable for use as construction materials. Bacteria also have potential in limiting the dusting of tailings and facilitating rehabilitation on closure. The paper describes a series of laboratory involving the addition of harmless bacteria to a range of tailings. The bacteria form a compact material called calcite (a common and stable form of calcium carbonate), which immobilises the tailings particles, releases water, and cements the tailings in a stable and natural matrix. The water released can be recovered or evaporated, depending on site objectives. The bacterial reactions are linked to physical and chemical processes, providing the potential for an optimal mix of technologies for particular tailings and site conditions.CITATION:Cifuentes, H and Williams, D J, 2018. Potential improvement of tailings geotechnical behaviour using bacteria, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 228–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Ali S. Al-Watban

"In this paper, the room temperature friction and deformation properties of various polycrystalline diamonds; i.e. aggregates of diamond crystals with a ""binder"" phase of cobalt and a polycrystalline coating produced by a chemical vapour deposition processes (CVD) were studied when softer metallic and ceramic sliders were used. The experiments were conducted· at relatively low sliding speeds (10 mm/min), in a vacuum of 10-5 mbr after having cleaned the specimen surfaces by out-gassing them for about 30 min at 800 °C. As a result of increasing the number of traversals significant wear of the coated diamond by softer metallic sliders (aluminium and mild steel) was observed. With ceramic sliders, it is shown that the multiple traversals result in the formation of wear groove. With diamond silicon carbide, high friction and adhesion lead to significant metal transfer which then pre-empts cumulative deformation of the harder materials. With the diamond-cobalt composite, the friction is surprisingly low, there accumulation of wear debris on the tip of the slider but no permanent transfer of metal and the harder specimen is not damaged even after 5000 traversal.IntroductionPolycrystalline diamond is mainly produced as tool materials for the machining of hard metals and composites. Thus, the sliding friction and wear resistance are amongst the most important properties relevant to those applications.During cutting by PCD the wear mechanism is mostly influenced by the chemical affinity between the tool material and the workpiece. For example, diamond based materials are not recommended for machining ferrous materials because carbon is highly solubie in iron: This leads to the graphitisation of diamond particles and hence a high rate of diffusion wear is observed (Brookes and Lambert, 1982)."

Jan 1, 2000

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By Earl M. Frizzell

This paper addresses considerations for the use of artificial support of pit walls in surface mines, a new project of the Bureau of Mines. Results to date indicate that a polymer-coated cable with embedded grit could provide good anchorage for stabilizing benches and highwalls, and an electronic method of recording discontinuities in the field is being reviewed and developed for application to mining. The objectives of the work in progress are to define the engineering parameters and evaluate the concepts for artificial supports in order to provide safe working environments when pit slopes are steepened to increase ore recovery and reduce overburden handling.

Jan 1, 1986

By S. W. Zehr, G. S. Murty, W. A. Backofen

AN observation by Squires, Weiner, and phillipsl has stimulated interest in a mechanism of deformation at high temperature (above -0.5 of the absolute melting point) that is not usually thought to be involved in the creep of metals. They found precipitate-free or "denuded" zones along grain boundaries normal to the stress axis in tensile specimens of a hydrided Mg-1/2 wt pct Zr alloy after slow straining at 450° and 500°C. Their suggestion that the zones were a result of directional diffusion of magnesium atoms was supported with calculations from Harris and Jones2 which also tended to identify the process as Nabarro-Herring (N-H) creep3,4—a process that is characterized by Newtonian viscosity, with stress (o) directly proportional to strain rate (C), and one that proceeds by lattice diffusion. Material transport by diffusion along grain boundaries is an alternative basis for Newtonian viscosity, as demonstrated by Coble,5 and is favored over N-H creep for fine grain size and lower temperature.6 In either case, the strain rate sensitivity of flow stress, defined as m = d log o/d log E (which commonly appears in the empirical a = KEW), is unity. The experiments to be described here gave metallo-graphic indications of diffusional creep which were no less clear than those just cited, but the associated m (as measured by the method of Ref. 7) was much more like that of a Bingham material. For true Bingham behavior, (a — ao) E, where oo is an initial yield stress. Therefore, even if flow after yielding should occur by diffusional transport, m must increase from 0 as < is raised to reach unity only in the limit as One result is that the resistance to tensile necking conferred by Newtonian viscosity is lost, which would become increasingly apparent through the formation of more sharply defined necks as 6 is lowered. That trend appeared in these experiments. Most of the work was done on an extremely finegrained alloy of magnesium with -6 wt pct Zn and ½ wt pct Zr (Mg ZK60); the initial mean-intercept grain diameter, L, was 0.55 µ. Shown in Fig. l(a) is a germanium-shadowed carbon replica of the surface of a specimen that was coated with silicone oil,* heated to 270°C under a helium atmosphere, and then stretched locally -200 pct at an initial E = 3.3 x 10-5 sec-1. Under

Jan 1, 1969

By Jong-Ren Tarng, Gin-Hwa Chen, Wen-ku Chang, Ke-Ming Lin, Yuan-Haun Lee

"The majority of early studies used X-ray diffraction, but this requires a model to interpret the diffraction processes. A turbostratic model has been applied by Warren, Franklin and Bacon to a wide range of materials including both soft and hard carbons. Maire and Mering applied the same methods to the interpretation of the (001) lines of a series of graphitic carbons. In our case, graphitic carbons undergone high temperature and high pressure graphitization processes have been evaluated by the same methods. It were found that most technological XRD data were obtained by a Rietveld method with the least-squares refinements could be in the simplest way since the full correction technique is very laborious. The behavior of carbon materials as it proceeds through the graphitization process is characterized by changes in the measured interlayer spacings (d) a~ a function of temperature. A series of graphitic carbons including the transformation of diamond to graphite through the process under high temperature and high pressure have been evaluated. A simple calibration equation has been established. IntroductionRecently, in battery industry, carbon materials are used as cathode in lithium ion batteries. However, graphitization of those carbon materials is concerned as if lithium ion intercalated into those carbon cathode. Both high-graphitization and low-graphitization carbon materials are suitable for this kind of application.As for graphitization, the starling materials from which carbons may be prepared vary extensively from pure chemical compounds, to mixtures containing II wide range of molecular weights, such as pitches. So its graphitizing, perhaps the most notable feature of the process, is the very wide range of temperature over which the perfection increase, unlike the more common transformations of solid state materials which occur in a narrow temperature range. The variables involved in the conversion of the initial hydrocarbon to a carbon residue, which may vary widely in final perfection, are time, temperature, stress and impurity content"

Jan 1, 1996

By J-S Han, J-M Yao

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Shagou deposit is located along NE-trending faults within the high-grade metamorphic basement of the Xiong’er Terrane in the Qinling orogenic belt. It is a large Ag-Pb-Zn deposit hosted in the Taihua Supergroup and has proven reserves of 1.54 Mt of ore with grades of 767 g/t Ag, 13.24 per cent Pb and 4.31 per cent Zn. The hydrothermal ore-forming process can be divided into early quartz-pyrite, middle quartz-polymetallic sulfides and late quartz-carbonate stages. Four types of fluid inclusions (ie pure carbonic, carbonic, pure aqueous and aqueous) can be distinguished in quartz. Fluid inclusion, hydrogen, oxygen and sulfur isotope systematics indicate that the ore-forming fluids are initially deeply sourced metamorphic water with meteoric water gradually mixed in the later stages. Sulfur isotope data show that the ore-forming fluids originated from both the Taihua Supergroup and the sedimentary successions of the Guandaokou and Luanchuan Groups (CSC) located to the south of the Machaoying Fault. A genetic model of the Shagou deposit is proposed as follows: CSC subducted northward along the Machaoying Fault beneath the Xiong’er Terrane during the Mesozoic collision between the North China Craton and South China Block. Subsequent dehydration resulted in the devolatilisation of fluids rich in CO2. These fluids migrated upwards, reacted with the Taihua Supergroup and formed the Shagou deposit.CITATION:Han, J-S, Yao, J-M and Chen, H, 2015. Fluid inclusion and isotopic constraints on the mineralisation of the Shagou Ag-Pb-Zn deposit, Henan Province, China , in Proceedings PACRIM 2015 Congress, pp 615–618 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By Irving Hartmann

Modern mechanized mining with high-speed machines, multiple-entry systems, multiple blasting, high-velocity air currents, and rapid haulage has brought many economic benefits and has on the whole enhanced safety in the coal-mining industry. It has, however, also introduced some added hazards, the control of which requires concerted effort and ingenuity. Mechanized mining has greatly increased the production and dissemination of fine coal seam or in mine entries. Use of high-speed machines has increased the probability of formation of incendive sparks, which are produced by frictional contact between moving metals and certain mineral substances in the coal seam or in the adjoining rock strata. In gassy seams rapid extraction of coal has increased the rate of gas evolution. These facts have made more urgent the need of preventing the ignition of coal dust and the development of widespread mine explosions. The ignition hazard can be controlled best by eliminating all potential igniting sources and by careful attention to ventilation designed to prevent accumulation of gas capable of triggering a coal-dust explosion. Frictional spark ignition by mining machines and suggested safeguards are discussed in a recent publication. Extensive research and long experience have shown conclusively that the propagation of coal-dust flames can be arrested and the development of widespread explosions prevented by properly applied, generalized rock dusting.

Jan 1, 1956

By Michel Papadakis

El presente texto señala el proceso de la molienda, utilización industrial, aparatos, clasificación, modos de utilización, estudio del comportamiento del mineral y la evolución de los problemas de trituración. El proceso de molienda consiste en trasladar el material del estado granuloso al estado pulvurulento. En ese sentido, se busca transformar los materiales con el fin de aumentar su superficie total, así como los cambios físico-químicos. Asi mismo se define el comportamiento de los materiales en los molinos de bolas.

May 1, 1961

By C. E. Chapin

The Hansen orebody is a large (1 2 million kg U3O8, 0.08% U3O8 average grade) sandstone-type uranium deposit in the Eocene Echo Park Formation of central Colorado. The deposit occurs in carbonaceous braided-stream sandstones that are part of a wet-alluvial-fan complex that prograded eastward across a narrow strike-slip basin. The Echo Park basin is one of a series of basins that formed along the east side of the Colorado Plateau as it was translated northward during the Eocene culmination of the Laramide orogeny. The valleys of east- and southeast- flowing perennial streams, whose courses were transected by the subsiding Echo Park basin, were filled with permeable volcanic and sedimentary rocks during construction of the Oligocene Thirtynine Mile volcanic field. These paleovalleys funneled large volumes of uranium-bearing ground waters through the braided-stream facies of the wet alluvial fan. Uplift of a basement horst downfan from the Hansen orebody reduced transmissivity and helped maintain a reducing environment in the Hansen area; this later became an important factor in preservation of the Hansen orebody. The horst also deflected uranium- bearing ground waters upward into the Oligocene Tallahassee Creek Conglomerate where they formed the Picnic Tree orebody (1.1 million kg U3O8, 0.09% U3O8 average grade) in an altered ash-fall tuff that is essentially barren above the Hansen orebody. Several potential source rocks for uranium are present and range in age from Proterozoic quartz monzonites of Silver Plume age to lower and upper Oligocene ash-flow and ash-fall tuffs. Uranium may have been contributed to the Hansen orebody several times from different sources. Uranium and thorium analyses of ash-flow tuffs indicate that ample uranium was released during cooling and ground-water leaching to form several Hansen orebodies. The host sandstones are conspicuously altered, and their initial high permeability has been greatly reduced by precipitation of intergranular cements, especially clays and opal C-T. The alteration and cementation mineral assemblages and the chemical composition of stagnant ground waters recovered from pump tests indicate that uranium deposition occurred under alkaline, reducing conditions preceded and/or accompanied by bacterial production of framboidal pyrite.

Jan 1, 2013

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Samuel B. Rombeger

The behavior of gold in hydrothermal systems is evaluated as a function of pH and oxygen and sulphur activities at temperatures to 250°C. Under conditions of stability of pyrite and argillic alteration as emblages, gold will be transported as bisulphide complexes. In systems containing significant amounts of arsenic, thioarsenide complexes may be important. Oxidation, dilution and reduction in sulphur activity would cause gold deposition from saturated solutions under these conditions. Gold chloride complexes will predominate under oxidized conditions where hematite or other oxides are stable and depo ition would result from increase in pH and/or reduction . Absorption and coprecipitation are po sible mechanisms of deposition for gold in certain low grade depo it . Low concentrations of gold in the transporting solution combined with the ignificant solubility of gold as bisulphide complexes, sugge t hydrothermal solutions rarely may be saturated with gold and coprecipitation with sulphides may be an important initial depositional process. Recrystallization of the sulphides in the presence of the hydrothermal solution would be re ponsible for release of gold to more table ite . Thi mechani m i supported by the close association of gold with pyrite in many hydrothermal gold deposits.

Jan 1, 1986

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Bianca Medeiros, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Daniella Cardoso Buzzi, José Roberto de Oliveira

"AMD is one of the main problems associated with mining activities and the techniques used in their treatment may be the biosorption. The aim of this work was to study the rice husk as a biosorbent for the AMD treatment keeping constant: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). And varying the contact time of 5, 20, 60 and 240 minutes. Rice husk samples will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. Since the infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests. AMD synthetic solutions will be analyzed by ICP in order to quantify the metals concentration captured by biomassIntroductionThe preoccupation for the environment has led the industry in general, to treat their waste. As the only industrial activity is increasing, the pollutants generated must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.In mining there is waste water with accumulation of heavy metals, and these are harmful to health of living beings, thus being one of those industries responsible for some pollution of the environment. These wastewater in contact with oxygen to generate an acidic water is called acid mine drainage (AMD). This aqueous solution has a pH below 3 and varieties of dissolved metals. When this solution comes in contact with water, generates a series of environmental problems, so there is a need to recover the metals present in the DAM."

Jan 1, 2012

By P A. Collier

The general view of the author is that all the good intentions of manufacturers can fail completely if the variations in circumstances in underground mining are not considered at all times. With a belief that it is the customer that has the experience and know ledge of problems which occur on long installations. Reilloc talk with customers in coal mines around the world, and have done so from their inception. With considerable experience in their home market, their technical approach was received with enthusiasm by coal companies in both Australia and South Africa, and whilst experience was obtained in other countries, it is the particularly close working relationship in these two areas that is covered in this paper. The refinement of manufacturing techniques and the fine tuning of the specification to which the chain is made was developed in conjunction with factual underground experience obtained by customers as they sought to improve their productivity and a reduction in working costs. With a reliable product the mines are able to concentrate on improved operational techniques to extend the useful working life and plan for multi-panel usage of the chain.

Jan 5, 1996

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994