Search Documents

Drilling is a common process in mining and petroleum engineering applications which have different objectives. For example, drilling deep boreholes in tight gas formations and gas shales is becoming more popular in the oil and gas industry. By contrast, drilling deep small sized holes for mineral exploration in hard rocks is performed to obtain samples for grade analysis purposes. In both applications optimising the drilling process includes using the most effective operating parameters such as rotation speed and weight-on-bit in order to maximise the rate of penetration. Obtaining the optimum drilling parameters requires sensitivity analysis over a range of data, which would be costly and time consuming during real field operations. Therefore, conducting several experimental simulations in the lab would be very beneficial before field operations begin. A drilling rig was designed and developed to simulate various drilling scenarios. The rig works in conjunction with an existing true triaxial stress cell (TTSC) which is in use for different petroleum related applications. The rig allows drilling into a cubic rock sample of up to 300 mm size. Three independent stresses can be applied to the sample to simulate real in-situ field stress conditions while the sample may be saturated with fluid. A significant feature of the rig is its ultra-high speed rotation which can rotate up to 8000 rpm: this is to simulate hard rock drilling for mineral exploration applications where large weight-onbit could damage the bit cutters. With the proposed design, a drilling fluid of any type can be circulated in the simulated borehole similar to the real situation, to study its effect on drilling performance. The TTSC drilling lid is equipped with torque and drag measurement systems which are two important drilling parameters to be recorded during drilling operation. It is believed that this new drilling rig will open opportunities for performing major new applied research in the area of more efficient drilling in both oil and gas bearing formations and mineral exploration applications.

Aug 1, 2013

By N. H. Coates

The Bureau of Mines determined average film coefficients of heat transfer for helium flowing through smooth, water-cooled tubes at Reynolds numbers of 5,000 to 25,000, helium inlet temperatures of 1,600° to 2,600° F, average temperature difference across the helium film of 800° to 1,300° F, and heat flux to 215,000 Btu/(hr)(sq ft). Since helium was the only gas used, the ranges of values for physical properties of the fluid are limited--thermal conductivity from 0.15 to 0.20 Btu/(hr)(sq ft)(O F/ft), viscosity from 0.082 to 0.104 lb/(ft)(hr), and Prandtl number from 0.63 to 0.68. Four equations, three of them dimensionless, correlate these coefficients with other properties of the helium--bulk temperature, film temperature, dimensionless parameters based on temperature, and the ratio of wall temperature to bulk temperature.

Jan 1, 1966

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By R. Ajalloian, L. Karimzadeh

This paper describes the engineering properties of Givi dam foundation. Givi dam will be built across the Givi River on the andesitic rocks (Karaj formation) in Ardabil province (northeast of Iran). Geotechnical investigations including drilling, pumping tests, sampling for laboratory testing and discontinuity survey. Physical and mechanical properties of andesitic rocks such as density, water absorption, porosity, uniaxial compressive strength, triaxial compressive strength, durability and direct shear tests are evaluated in this paper. Discontinuity data are process for the determination of dominant sets and for the rock mass characterization in terms of classification systems ( RMR, Q and RSR ). Correlations between these three classifications are discussed. Le barrage doit être construit sur la rivi_re givi qui cou_e sur les andesites (formation de Karaj)dans la province d_ Ardebile situee_ a Nord- Ouest de l_ _Iran. Les études géophsique commesondage, Pompage. Et échantillonnage afin de verifier les discontinutés out éte_ effectuées. Lesproprietés physique et méchanique des roches andesifique ont éte_ verifieés. Les informations concernaüt aux discontinuitiés afin de montrer leur principale direction ont éte_ verifieés, les proprietés des roches dans leurs ensemble ont éte_ etudieés. Les divers classifications(RMR,Q,RSR ) ont éte_ comparés et analyseés. Dieses Schreiben ist zur Erklaerung der Ingenieureigenschaften ueber Baugrund des Givi Deiches.Dieser Deich soll im Givi fluss auf Andesitgesteine (Karaj formation) gebaut werden. Der platzdes Deiches legit im Ardebil Provinz nordwestlich von Iran. Geotechnische Untersuchungen Sind:Bohrungen, pumpen Versuche, Probenentnahme fuer Laborversuche, BrechbarkeitBestimmungen, physikalische und mechanische Eigenschaften der Andesitgesteine wurde hierausgewertet, wie Z.B.: Wasserleitfahigkeit, Porositaet, Scherfestigketswiderstand, Informationenueber Brechbarkeiten der Gesteine wurde gesamelt, und die meisten Brechbarkeiten bestimdamitman die Gesteine besser klassifizieren kann. In Endefekt wrid die Resultate verschiedeneKlassifizierung wie RMR, Q, und RSR besser geachtet und zusammen vergliechen.

Jan 1, 2003

By D. B. Apel

As depths to the ore bodies keep increasing around the globe, the problem how to deal with the increasing temperature of undisturbed rock mass becomes very important. In extreme cases the rock temperature at the bottom of the mine could raise up to 80 °C. In deep mines, geothermal heat is considered as the primary heat load contributor, which accounts for 50?90% of the total heat load depending on different geological conditions. Thus the geothermal heat control in underground mines is the most important and demanding issue to ensure a suitable working environment. In this study, expanded perlite aggregate (EPA) was incorporated as a lightweight substitute for sand. Five mixtures were prepared using 0, 25, 50, 75 and 100% replacement ratios of sand by EPA. These, mixtures were tested in the laboratory for both the insulating and strength properties of the developed shotcrete. The goal of this research was not only to develop shotcrete which would exhibit good insulating properties but also which would exhibit strength properties similar to the regular shotcrete. This paper not only reports the results of the laboratory tests but also discusses the output of numerical model which was performed to evaluate the benefits of using the insulating shotcrete in reducing the cooling costs at hot underground mines.

Aug 1, 2013

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969

When Caterpillar announced that it had purchased Bucyrus for $8.8 billion, it was billed as the next great chapter in the history of mining. Surely, when the history books are written, it will be remembered as a deal that changed the face of the mining equipment sector, and it could well be a major milestone in the path toward autonomous mining in the future. In the short term, the deal is a clear indication that the world?s largest equipment maker is bullish on the mining sector. The purchase of Bucyrus allows Caterpillar to expand its mining interest to six product segments (underground, surface extraction, large mining trucks, surface material handling, hauling products and growth markets) with 16 product lines to serve the mining industry. But the commitment doesn?t end there. According to Steve Wunning, president of Caterpillar?s resource industries group, which includes Cat?s global mining division, the commitment to mining goes far beyond the acquisition of Bucyrus.

Jan 1, 2011

By Madan Kumar Annam, Hari Krishna Y, I. V. Anirudhan

"For completion of projects in time with positive results, improvements of productivity and effective project management procedures have become extremely important. This paper discusses a milestone project comprising 198 residential units of stilt plus 4 levels that highlighted the benefits of these key aspects. Success of ground modification procedure benefitting the entire cycle involving End Users, Suppliers, Bankers and Developer is discussed.Soil profile for a considerable depth comprises weak layers of silty clay and sandy clay with varying consistency. Deep foundations have been an automatic choice of foundation for major buildings constructed in similar environment. After serious geotechnical appraisal, reconsideration of the foundation system with an alternative solution of Ground Improvement was found to be optimal in terms of Cost and Time. Full raft foundation on the improved ground by installation of Vibro Stone Columns (dry bottom feed method) was considered as an alternative foundation system. The ground improvement works were completed within 6 weeks (as against 6 months to that of pile foundations) that was made possible through effective project management. Full size plate load tests were conducted to ascertain effectiveness of the ground improvement works. Success of the foundation system was proved by full scale monitoring of foundation settlement during and after completion of the project over a span of 2 years. This paper describes design considerations, quality control in the construction of Vibro Stone Columns (dry bottom feed method) and performance monitoring of the project thereafter.INTRODUCTIONGenerally in weak deposits, deep foundations like bored cast-in-situ piles and driven piles have historically been the foundation choice for major buildings and other structures. Construction of pile foundations is becoming a challenge due to their high cost, large construction time and due to severe environmental issues (noise pollution, ground vibrations and carbon footprint). Since the proposed building complex is located within the proximity of a well-developed residential locality, objections raised by neighborhoods to pile driving activities called for a rethinking on the foundation system.The top 6m to 8m of soil profile comprises of silty clay / sandy clay having highly varying consistency. GWT was encountered at 3.0m below the existing ground level. Under this situation, the reconsideration of the type of foundation system with respect to the geotechnical analysis gave a thought to assess feasibility of ground improvement system."

Jan 1, 2015

By A. Brown

RAPIDLY rising world demand for mineral pro- ducts has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations.

Jan 8, 1958

By D. Newman

"The U.S. stone industry is in a transition from surface quarries to single and multiple level underground stone mines. The factors driving this transition include surface quarries; ? reaching their economic stripping ratio, ? encroaching on the mineral reserve boundary where the remaining reserves are below the active pit, ? dust, noise, and blast vibration concerns as suburban neighborhoods and development move into formerly rural areas. Ground control is critical to the success of a safe and productive, mining operation. The primary focus of the ground control engineer in an underground stone mine is the stability of the roof or back, development and benched pillar stability, stability of the sill pillar between vertically adjacent mining levels, and floor stability. Roof stability begins with the selection of a stable back horizon based upon the presence of a thin shale parting, stylolite, or other discontinuities from which the production shot can easily ""peel"" away leaving a stable back stratum. Room width and the decision of whether to bolt the roof, the bolt length, bolt type, bolt diameter, and spacing of the support is controlled by the thickness, fracture spacing, jointing, and material properties of the back strata. Horizontal stress controls the header and crosscut azimuth as to avoid driving perpendicular to the maximum horizontal stress direction. Stable pillar dimensions depend upon the interaction of the; ? vertical stress resulting from overburden thickness and multiple level interaction of overlying level(s), ? mining height during development and the final mining height after floor shots are taken while benching, ? presence of faults, folds, or joints passing through the pillar, and ? stone lithology recognizing that the presence of oolitic bands, shale partings, and bentonite beds create zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture sensitive strata, weak stone bands, or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. The ground control issues for underground stone mines are most clearly presented through a series of case histories. The case histories presented in this paper are a mix of ground failures and successful mining. The focus is on the geotechnical data required for underground stone mine ground control for roof, pillar, and floor design and stability analysis."

Jan 1, 2016

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By Travis A. Davidsavor, Charles Dowding, David A. Provost, Yonggang Gou

This paper compares measured blast induced strains on operating, full scale, buried pipelines with three similar past studies. The recently performed study represents realistic and modern pipeline blasting techniques combined with modern data acquisition. The evaluation compares measured PPV and strain, as well as calculated stress, at equivalent scaled distances.

Feb 1, 2020

An active list of permissible explosives was published in December 1936 as part of Bureau of Mines Report of Investigations 3324, under the title "Active List of Permissible Explosives and Blasting Devices Approved Prior to July 31, 1936." This list included 170 brand names. Changes in the list that have been authorized to June 30, 1937 placed 35 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Ten permissible explosives were transferred from the active to the inactive list. The present list contains 196 brand names, one explosive having been placed on the list subsequent to June 30, 1937. The brand names of the permissible explosives placed on the active list are as follows:

Jan 1, 1937

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By C. H. Li, R. J. Stokes, T. L. Johnston

Dislocation half-loops, artificially introduced by sprinkling with carborundum, were subjected to stress using three-point loading. The different stages of loop expansion and multiplication were then correlated with the macroscopic stress-deflection curve. Loop expansion started at approximately one-third of the "yield stress," defined here as the motivation stress. Above one-half of the "yield stress" simple multiplication commenced while about two-thirds of the yield stress gross multiplication developed short slip-line segments. These values were not affected by the age of surfaces exposed to both dry and wet air. Slip was not detected on unsprinkled crystals below two-thirds of the "yield stress." Thus the stress to activate intrinsic sources, defined here as the activation stress, was approximately twice the motivation stress. This relationship was independent of the strain rate used. It is concluded that lattice resistance takes the form of a viscous drag rather than a static type of force. THE importance of surface condition and environment as one of the more significant factors controlling the mechanical properties of ionic solids has recently received renewed attention.1-4 In some materials, notably the alkali halides, exposing freshly cleaved specimens to the atmosphere results in a progressive hardening and embrittlement of the crystals. This has been attributed to the surface layer becoming "aged," thereby restricting the motion of dislocations in such a way that pileup and eventually fracture results. It is necessary therefore in studying the mechanical properties of ionic crystals to inquire first into the density and distribution of dislocations in the normal cleaved surface and to understand the role these dislocations play in the onset of plastic flow. Knowledge of the effect of environment on this behavior will then assist in understanding the mechanism of embrittlement on aging. In the work reported here a method is described for studying the initiation of plastic flow from dislocation sources in the surface of magnesium oxide crystals. Preliminary results are described of the influence of surface age on this behavior. EXPERIMENTAL TECHNIQUES The magnesium oxide used in this investigation was obtained from the Norton Co. and had a nominal purity of 99.5.pct. Single-crystal specimens, having dimensions typically 1/4 by 1/8 in. cross section and 1 in. in length, were prepared by cleavage over (100) planes from the parent crystal. They were deformed under three-point loading with 3/4 in. spacing between the two end supports and a constant rate of deflection at the center of 0.001 in. per min. The maximum strain rate therefore was 1.5 X 10-5 sec-1. Reasons for choosing this particular form of loading will become apparent in a later section. In addition, a number of confirmatory type tests have been performed at higher loading rates where the maximum strain rate was increased to 1 x 10-3 sec -1. Following deformation the crystals were etched to reveal the dislocation distribution. In a previous paper5 we described a satisfactory etching solution consisting of 5 parts of saturated ammonium chloride, one part of sulfuric acid, and one part distilled water. Immersion of the crystals for 1/4 hr at room temperature developed reproducible conical etch pits at the points where dislocations emerged through the surface. It should be mentioned that dislocations freshly introduced by room temperature deformation gave sharply pointed etch pits which generally distinguished them from the almost flat-bottomed pits obtained on "grown-in" dislocations. The distinction is obvious in the photomicrograph included in Fig. 5(b). Annealing crystals at 1000°C for 12 hr on the other hand gave sharper etch pits on the grown-in dislocations and the distinction was no lower -possible; a similar observation has been reported for lithium fluoride. We have succeeded furthermore in chemically polishing magnesium-oxide crystals. Boiling in fresh 85 pct ortho-phosphoric acid for only 1 min resulted in a microscopically smooth surface which could again be etched to reexamine the dislocation distribution. This boiling time was sufficient to remove the surface damage introduced by cleavage (see next section). SURFACE DISLOCATION SOURCES There are a number of ways by which dislocations may be introduced into cleaved surfaces to act later

Jan 1, 1960

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018