Search Documents

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Develop a means for estimating vertical stress conditions in or around an underground mine so that appropriate measures for ground control can be taken before hazardous conditions arise. Background High vertical stress in an underground mine could cause or enhance hazardous ground control conditions which might lead to accidents, fatalities, and loss of reserves. An understanding of the vertical stress conditions at the mining level would allow a mine operator to take precautions that will minimize the occurrence of ground control problems. A knowledge of the underground stress conditions prior to mining could be used as an aid in future mine plan development to avoid or minimize ground control problems. Approach The Bureau of Mines developed a computer program for calculating the vertical stress resulting from the pressure of overlying rock masses on a mine or geologic surface at various depths.

Jan 1, 1990

By John Cory, David Lily, Bill Hissem

The Lafarge granite quarry in Cumming, Georgia is using Principal Component Analysis (PCA) and Biplot charting to identify important variables and control air blast and vibration. Every blasting situation is unique and PCA and Biplot charting help to clarify the major variables determining air blast and vibration.

Jan 1, 2010

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By X. T. Feng, Y. H. Hatzor, Y. Tal, G. Yagoda-Biran

"When studying jointed rock mass deformation around underground openings it is of great importance to model correctly the excavation sequence during the numerical simulation. This is because for effective arching mechanism to develop in the roof minute block displacements must take place and some of the available discontinuities shear strength must be mobilized. If from the beginning of the simulation the underground opening already exists in the numerical model, block displacements into the excavation space will initiate and develop from time zero, before the initial stresses in the model have attained their actual initial level in the field. These initial block displacements are therefore artificial and exist only in the numerical model, not in the physical reality, and may lead to erroneous assessment of the stability of the designed structure, typically on the conservative side. We have introduced sequence excavation capabilities both in the numerical manifold (NMM) and the discontinuous deformation analysis (DDA) methods and show here the advantages of this modification using three different case studies, each illuminating a different aspect of this enhancement.We begin with the 25 meter deep 2000 year old underground Zedekiah limestone quarry below the old city of Jerusalem, Israel, which is still standing today unsupported with a free span of 40 m. We show that when the opening exists from the beginning of the numerical simulation the required friction angle for roof stability is 25 degrees, whereas when the opening is removed after all stresses and displacements in the model have been stabilized the required friction angle for stability is only 15 degrees.We then model the excavation sequence of a tunnel model representing a 2500 meter deep research tunnel in the Jinping hydroelectric project, China, in order to determine the in situ stress field at this depth by a grid search inversion of displacement data obtained using the sliding micrometer technology in the course of tunnel excavation. Thus we are able to constrain the in situ stress field at these depths where standard in situ stress measurement procedures are extremely difficult to execute properly.Finally, we use sequence excavation modeling capability to find the total height of the expected loosening zone around tunnels excavated through columnar jointed basalts which pose a great engineering challenge because of the characteristic dense network of slender prismatic blocks that transect the opening at a steep inclination. We use MPBX data obtained during excavation of a deep tunnel through such a rock mass to validate our numerical results and show that application of standard empirical guidelines for dimensioning rock bolt reinforcement in such rock masses may in fact result in very un-conservative design because existing empirical approaches typically ignore the anisotropic nature of the structure of such rock masses which, as we show, plays a very significant role in determination of the extent, shape, and geometry of the loosening zone around the opening."

Jan 1, 2015

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Meng Xiao, Peng Huang, Lizin Lan, Feng Ju, Shuai Guo

"Through changing the axial load on backfilling material compaction test to reflect different overlying strata pressure on backfilling material, the stress-strain relations in the compaction process of backfilling material under the geological condition can be obtained. Based on the characteristic of overlying strata movement in backfill mining, a model of roof thin plate is established. By introducing the stress-strain relation in compaction process into the model and using RIZT method to analyze the bending deformation of roof, the bending deflection and stress distribution can be obtained. The results show that the maximum roof subsidence and maximum tensile stress occurring at the center are 255mm and 5 MPa, respectively. Tensile fracture of roof under the geological condition of Dongping mine did not occur. The dynamic measurement results of roof in Dongping mine verify the theoretical result from the aforementioned model, thereby suggesting the roof mechanical model is reliable. The roof thin plate model based on the compaction characteristic of backfilling material in this study is of importance to research on backfill mining theories and application of backfilling material characteristics.INTRODUCTIONSolid backfilling mining (SBM) is a green mining technology in which the solid waste materials is placed into the gob to support the overlying strata and to control roof's subsidence and movement (Miao, 2012; Miao et al., 2010, 2015). SBM has been successfully used in several mines to solve many problems, including coal extraction under buildings, water bodies and railways, surface subsidence, and environmental problems. Good results have been obtained in many mines (Zhang et al., 2009). The key in the application of SBM technology is controlling strata movement. However, the critical factor influencing the controlling effect of strata movement is compaction characteristics of backfilling materials. Thus, a roof model of SBM is built based on the filling materials' compaction characteristics. A subsidence equation and the critical failure condition of roof was given and field verification was performed at Panel 15061 of Donping Mine."

Jan 1, 2016

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

By G. E. Bobeck

The first year's work of a proposed three-year study of the effects of the exposure of coal mine roof rocks to the mine atmosphere has been completed. The project has been terminated. The goal of the project was to determine if possible the mechanism or mechanisms by which coal mine roof rocks interact with the mine atmosphere and weaken, and coupled with mechanical stresses, ultimately fail. The scope of the study was limited to the effects of environmental factors on the deterioration of the rocks. While mechanical stresses may play an important role in the interaction of environmental factors, stress effects were excluded from the study. In order to study the effects of environment on coal mine roof rocks, samples were obtained from several coal mines in the western states. The rocks forming the roofs of most of the mines visited were shales of varying composition. These shales were subjected to numerous tests to determine how the rocks changed with time after exposure. In addition, the identity of the minerals present in the shales was determined by x-ray diffraction analysis and by thermal analysis as well as by optical microscopy

Jan 1, 1973

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By Arash Saeidi Rashk Olia, Dunja Perić

The increasing demand for renewable energy has attracted attention to energy geostructures as means of extracting clean geothermal energy from the ground. To further advance the understanding of soilstructure interaction in energy piles analytical solutions considering the self-weight of the pile were derived. These solutions were then incorporated in recently-derived thermomechanical weightless solutions to provide comprehensive analytical solutions for axial displacement, strain and stress in single energy piles. This was accomplished by comparing responses of energy pile under different loading scenarios that reflect presence and absence of the self-weight. Results of mechanics-based analysis revealed that the self-weight of energy piles embedded in stiff soils has no significant contribution to displacement, strain and stress that develop under thermo-mechanical loads. Overall, the significance of the self-weight contribution depends on the magnitude of thermal load as well as the soil-pile interface stiffness. The stiffness of end restraints imposed to the pile head and tip were also found to play an important role in contribution of self-weight in induced thermomechanical stresses in energy piles.

Oct 1, 2022

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017