Search Documents

By F. Mielli

Over the last three years there has been an increase in mining congress and conferences focusing on water management. Water in mining is a key concern for mine managers and operations, and we are now seeing this operational dilemma escalated to the level it deserves. According to Frost & Sullivan research, mining water and wastewater treatment and its related technologies will be a U$3.6 Billion global market in 2016, which translates the importance of this issue. Looking at the current mining trends, some factors increased the importance of water in mining operations, including: ? Future mining investments will be located in geographical locations where water is scarce (water stressed areas) ? A decline in grade will increase the intensity of mineral processes and therefore increase the use of the water ? Increased sustainability and regulations will extend the control/monitoring of water during the entire mine life cycle representation of the mine water flow system. A water balance has several benefits/objectives in a mine operation: ? Mine planning/simulation of mining scenarios/climate change Production optimization ? Minimizing strategic and operational risks ? Social license to operate ? Water-smart mine planning ? Target: water neutral mines ? Benchmarking within and between sites ? Sharing knowledge/technology transfer ? Reporting/communications ? Permitting/Compliance

Feb 23, 2014

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By Kwan Ho Kim

The beneficiation study of low quality pyrophyllite is conducted to enhance the value of it by selective grinding. In mining stage, the main gangue mineral is quartz, and the content of quartz in ore has an adverse effect on the quality of pyrophyllite. Using the huge difference in hardness between quartz and pyrophyllite, the selective grinding is accomplished using stirred ball mill. As a result, a finer pyrophyllite particle can be easily separated from coarser quartz particle by simple size classification, and the content of Al2O3 of fine particle smaller than 45um increased largely. It means that the pyrophyllite particle is ground selectively compared to the quartz particle, and the quality of pyrophyllite is enhanced.

Sep 1, 2012

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025

By Bruno Pinheiro Silva, João José dos Santos Carvalho, Flávio Túlio Busatto, Leonardo Passos Perdigão

Sinter has high participation in the blast furnaces ferrous burden in ArcelorMittal Tubarão, being therefore of paramount importance the constant control of its physical, chemical and metallurgical qualities, aiming at the fulfillment of the client required quality. With the great challenges faced by market conditions, steelmaking companies seek operational sustainability, aiming at stability and reducing costs. One of the main steps to obtain these results in the Blast Furnaces is the raw materials quality stabilization, in order to guarantee the perfect burden distribution control and a better use of the reductant gas inside the reactor, aiming a lower fuels consumption. It is known that the smaller a ferrous particle is, better its reducibility, since a larger surface area provides greater contact with the reductant agent. Based on this concept, the objective of this work is to quantify the effect of the sinter size produced in ArcelorMittal Tubarão Sinter Plant in its reducibility, and in this way enable the definition of a better sinter particle size distribution aiming at a balance between the permeability effects and gaseous yield in the Blast Furnaces. In addition, the reducibility effects on sinter size reduction were evaluated, where the 5 to 10 mm fraction was analyzed in two sinter samples, the first obtained from the conventional route and the second after crushing of the fraction over 50 mm, in order to simulate the effect of the use of a Secondary Crusher in Sintering.

Oct 1, 2019

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By Vicken Aprahamian

"The Royal Canadian Mint (RCM) operates a gold and silver refining toll operation in Ottawa, Ontario, Canada. The silver refining line is a recent addition and was commissioned in 2005. One source of silver in the refinery is from gold doré which undergoes Miller chlorination before electrorefining to 99.99% cathode gold. Treatment of the Miller salt or silver-copper chloride produced consisted of a 2-stage high temperature reduction process step using soda ash prior to 2005. Copper-rich silver bars were produced and shipped offsite for further refining.The copper-rich bars could not be blended into sufficient high grade silver doré to dilute the copper and allow electrorefining in a silver nitrate medium. A new wet process was developed and commissioned to replace the high temperature reduction and allow removal of bulk copper. Thus upgraded impure silver produced was cast into anode for electrorefining to 99.9% purity silver flake. The 2005 RCM Hydromet Slag process is presented as well as its more current version. In addition, mention is made of a novel processing scenario for the introduction of Miller chlorination silver into the electrorefining circuit."

Jan 1, 2015

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,' the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill's Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

By Joe H. Skidmore

This paper, describing mining and milling methods and costs at the Gold Hill mine, is one of a series being published by the Bureau of Mines. Boise Basin, in which the geld Hill mine is located, is in the central part of Boise County, Idaho, about 30 miles by air line northeast of Boise. The mine, owned and operated by Talache Mines, Inc., is at the southern end of the town of Quartzburg. About 115 to 125 tons daily is mind by square-setting and is treated in an amalgamation plant.

Jan 1, 1938

By Francis J. Kiessling

Energy and the conversion of potential energy into alternate forms is becoming a topic of household conversation for a larger segment of the world's population as mankind's desire for products derived from the vast array of technological developments continues to expand. The world's use of steel and the high energy consumption related to the production of steel promotes an awareness of the limitations of existing technology and a search for more economical alternates. Terminology such as (BF) Blast Furnace, (BOP) Basic Oxygen Furnace, (EAF) Electric ARC Furnace, (DR) Direct Reduction, (DRI) Direct Reduced Iron and (FC) form coke is becoming commonplace as alternates are being sought to alleviate the energy crunch. Coke production by various methods was developed as early as the seventeenth century in Europe to replace the disappearing hardwood forests that supplied the initial blast furnace fuel in the form of charcoal. In 1880, the Semet Solvay by-product coke oven design was introduced to the United States at Syracuse, New York, to supply coke for use in the production of soda ash, coke oven gas and its by products as the primary source of many organic processes. Although the Semet Solvay coke oven has not been marketed for decades, these coke oven batteries are in use today producing metallurgical coke, coke oven gas, and related by-products.

Jan 1, 1980

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By P. C. McWilliams

The Bureau of Mines investigated ground support problems in four major block-cave mines to assess the current "state-of-the-art" and to delineate areas for future research. The most significant problem is the inability of present support systems to hold moving ground. Further, as mining progresses to greater depth, this problem becomes more serious. Providing adequate temporary support capable of withstanding primary and secondary blasting is the next most significant problem. A detailed analysis of the effect of mining methods on support problems is also recommended for future research.

Jan 1, 1975

By Kathleen M. PH. D. Kowalski

This paper discusses human judgment and decision-making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision-making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behavior in underground mine fires. The authors assert that stress is one of the factors that decision-makers must contend with in most life-or-death situations. They suggest that a better understanding of individual's judgment and decision-making activities while under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers, and policymakers.

Jan 1, 2008

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By J. E. Spurr

"Zinc Industry in BelgiumBy March F. Chase, Consulting Metallurgist, Bureau of MinesBelgium for many years was the principal spelter producing country of the world. Gradually its production was surpassed by that of Germany, and Germany in turn lost first place by the production in the 77ti.tad States. For the ten years previous to 1914, 21.6 per cent of the world's spelter was produced in Belgium. Of this production approximately 40 per cent was exported. A large percentage of the balance was rolled and of the shoots thus produced a considerable quantity was also exported.From an economic standpoint even before the war, the Belgian industry was in a unique, if not praoarious, position. Dependent upon foreign countries for ore and foreign markets for sale of products, smeltor was at a distinct disadvantage when compared with some of those of other localities. These disadvantages were partly offset by cheap coal and labor and by whatever there is of value in experience and what we may term for want of a better expression smelting tradition. However intangible this latter may be, it did have and has today an influence on commercial operations.One must not overlook the effect it will have on the revival of the industry. It may not be the determining factor but the fact that for so many years this industry flourished in Belgium, and played such an important role in the industrial life of the country will decide many operators to attempt to re-establish their operations.In 1913 the Belgian spelter plants produced 204,220 long tons of spelter or approximately 20 per cent of the world's production. During this year 500,000 to of ore were treated. The actual value of all of the products derived from treating sine ore amounted to 225 million frames."

May 1, 1919