Search Documents

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By Manqiu Xu

"Ore grades are decreasing and ore deposits are becoming more complex. In order to make a sound economical decision about a mining project, metallurgical testwork must be carried out. A few large “representative” samples cannot represent the metallurgy of a large ore body and a large number of samples reflecting variation in ore head grades and in mineralization types must be obtained for proper metallurgical studies, including flowsheet development for a greenfield project. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to establish a correlation between values recoverable and values contained in the ore body that can include multiple pay metals. With this information, a sound economical decision can be made about the viability of a large mining development project.INTRODUCTIONThe demand for minerals today is historically high as many countries are being rapidly industrialized. The supply for these minerals is not necessarily running short. However, it is widely accepted that the world today is running short of the easy to mine and easy to process ore deposits. As ore grade is decreasing and ore mineralogy is becoming more complex, metallurgical testing must be fully conducted in order to make a sound economical decision about a mining project. For a high-grade and high-quality deposit, it is hard not to make a good profit even with low metal prices. For a low-grade and hard to process deposit, the profit margin is much lower and is dependent on the throughput and the recovery of valuable minerals. The recovery of valuable minerals is a function of ore grade and mineralogy and it must be experimentally determined for a given processing option.At Vale Base Metals Technology Development, metallurgical testing for an existing operation or brownfield project is termed as Ore Evaluation, while metallurgical testing for a greenfield project is termed as Flowsheet Development (Xu, 2011). In the past, metallurgical testing involved a few large composite samples for lab and pilot plant testwork. As ore deposit becomes less homogeneous and more variable, a few large composite samples cannot represent the metallurgy of a large ore body. In addition, useful information about the deposit such as zones of “impurities” or floatable rock minerals would not be obtained. Different processing strategies could have been developed if the locations and sizes of these zones were known in advance. For proper metallurgical studies, a large number of samples reflecting variation in ore head grades and in ore mineralization types must be used. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to estimate values recoverable in the ore body that can include multiple pay metals. Ultimately, the recovery verses ore grade relationship will be used in business decision-making."

Jan 1, 2013

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By J. H. Adkins

The goal of the project reported in this paper was to make recommendations for changes in roof bolting procedures and bolter design that would reduce roof bolter accident rates. To that end the project identified the major hazards associated with each task a roof bolter operator per-forms, normalized task accident frequencies. by the time spent on each task, reviewed equipment design features and operating procedures related to the identified hazards and developed recommendations for equipment and procedural changes that would reduce, if not eliminate, the hazards. The research steps completed during the project were: a. A review of related literature and re-search including roof bolting time studies b. The collection and analysis of 1975 accident data pertaining to roof bolter activities c. The normalization of the accident frequency data on the basis of time/task data d. A review of roof bolting equipment e. The development of a field data collection instrument f. The selection of mines for bolter observations g. The collection of field data h. Data analysis and problem specification i. The development of recommendations for corrective measures

Jan 1, 1978

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By George P. Demopoulos

For more than 20 years the author had the privilege of working closely on a number of R&D projects with Lucy Rosato and her team at CEZinc. Several of these projects were driven from the sustainability agenda that Lucy Rosato championed as an innovation leader that supported research collaborations. Highlights from this highly rewarding collaboration are to be presented in this paper. In particular we will deal with the following works-topics: (a) iron control via solvent extraction as alternative to jarosite precipitation; (b) production of high-density gypsum by controlled neutralization of simulated zinc plant process/waste waters; (c) selenium removal from weak acid solutions; (d) electrolyte purification by cementation; and (e) manganese control by oxidative precipitation with SO2/O2.

Jan 1, 2015

By Nath S. Parate

With the extension of mining beneath residential and industrial areas, it is becoming increasingly necessary to extract coal and minerals in such a way that subsidence damage due to groundmovement is reduced to a minimum. Understanding clearly of the mechanism of subsidence development is a must in view of the environmental problems and the energy crisis today. This paper gives a simple analysis of various components resulting from subsidence and the influence of other factors on their development. An up-to-date review of the subsidence and strain profiles is presented, with particular references to the coal mining operations. The importance of this topic from mining damage to structures, buildings properties and environment in mining areas is undeniable. Field results are discussed.

Jan 1, 1982

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By G. C. Price

This study traces the development of the bucket-wheel excavator, points out the differences in the German- and American-type wheels, and gives the major design criteria and the advantages and disadvantages of bucket-wheel operations. A computer program, written in FORTRAN IV for use with an IBM 360 computer, simulates the operation of the digging components of a bucket-wheel excavator. By supplying certain mining dimensions, soil characteristics, and machine design specifications, this program will print out a time study of the various components of an operation, power calculations for the operation, and production data. This program, when combined with a truck, belt, or rail program, should be helpful in planning a complete mining system In material suitable for a bucket-wheel excavator operation.

Jan 1, 1973

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By R. L. Stanton

"The present contribution examines, in some detail, what appear to be the three outstanding features of the field occurrence of the conformable ""pyritic"" deposits. These are their association with fragmental volcanic rocks (and derivatives), their occurrence in sediments of near-shore formation, and their highly variable structural associations.In a recent paper it has been suggested that two such ""pyritic"" de-posits in New Brunswick may have originated as marine concentrations of volcanic base metal and sulphur compounds, and that many of their present features are the result of diagenesis, folding, and regional metamorphism. This is now put for-ward as a general explanation for the particular class of deposit considered.Such deposits should, on this hypo-thesis, be regarded quite simply as an integral part of the particular geological environment in which they occur -as a normal, though minor, sedimentarry type developed, char-acteristically, in near-shore and shelf facies of intravolcanic units formed along the margins of eugeosynclines. They should not be considered -as, for example, is required by the re-placement theory -as later features simply superimposed on a geological situation to which they are genetically unrelated. Where they are associated with folds and other structures, this may be attributed, from one in-stance to another, to mechanical migration during folding, weaknesses induced by pre-existing sulphides, and, occasionally, to fortuitousness.In the light of this postulated origin, it is suggested that the first stages in regional prospecting for deposits of this particular class should be broadly palaeogeographical. Later phases of the search should then be directed to the delineation of sedimentary facies and, finally, to the investigation of geological structure."

Jan 1, 1960

By E. G. Charlesworth, M. J. Robertson

"Abstract - Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots.Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confined largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semi­ massive sulfides within tension fractures which are folded, attenuated and fractured .An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

By Hugh M. Wolfin

This Information Circular is an abstract of a manuscript which was completed in June 1933, by Mr. Hugh M. Wolflin, formerly of the U. S. Bur eau of Mines. This abstract has been prepared by Charles Will Wright for presentation at the February meeting of the American Institute of Mining and Metallurgical Engineers in New York. It has been necessary to omit many of the details and most of the cost data and tables, as well as the illustrations in the original manuscript. As the use of airplanes in mining developments is making such progress and as a publication on this subject to be of greatest value should include the most recent information, it is unfortunate that, due to a lack of printing funds, it has not been possible to publish this manuscript. The purposes of Mr. Wolflin's paper are: (1) To describe briefly what has been accomplished in some outstanding examples by the use of aircraft in the mining and petroleum industries, (2) To record costs, (3) To present available information and suggestions to assist in solving future air-transportation problems in the industries under consideration.

Jan 1, 1934

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Fredy Llerena B.

El presente trabajo describe la geología del depósito minero Candelaria, perteneciente al distrito minero de Castrovirrey, Huancavelica. Dicho depósito está asociado a la actividad ígnea de centros y domos volcánicos del terciario medio o superior, mientras que la veta Candelaria está constituida por tetrahodrita, enargita, boulangerita, bournouita, jamesonita, esfalerita, galena, bismutinito, chalcopirita y como minerales de ganga, pirita, cuarzo, barita, oropimente, regelgar, marcasita, arsenopirita, así como hay lazos cimoidea. De otro lado, las intersecciones de vetas favorecen la mineralización y el Domo Volcánico Candelaria es favorable a la mineralización al igual que los tufos.

Oct 14, 1980

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By E. D. Doney

The Kerr-McGee Coal Corporation's Galatia Mine's first longwall mining system was implemented on May 3; 1989. Start-up of the longwall face represnted the successful conclusion of an effort begun nearly four years earlier. This paper-presents a case history of the processes that led to the longwall's implementation, and the subsequent mining of the first 7,900 foot long panel.

Jan 1, 1990