Search Documents

By R A. Lynch

The state-of-the-art in cave seismic monitoring is reviewed, with the latest developments in active seismic monitoring included. Seismic monitoring systems are routinely used by most of the world’s block and panel caving mines to track the cave initiation and progression. The current best practice is to use the cloud of seismic event locations as a proxy for cave growth somewhere below. Problems with event location reliability due to seismic ray bending around the (unknown) cave are side-stepped by using sensors installed above the cave. However, the aseismic gap – the (unknown) distance between actual cave back and seismic event cloud – currently hinders reliable estimation of cave geometry.Velocity inversions using the passive seismic data are inexpensive and should be undertaken more routinely. The straight-ray methods should be used with caution, as the underlying assumptions are invalid in caving environments. The double-difference method is more correct for the caving situation, and there have been some promising results published. Constrained geometric inversions make a lot of sense, but have yet to be demonstrated successfully.Two active seismic source have recently been developed for use in the caving environment: a piezoelectric source for ranges up to a few hundred metres and a pneumatically-powered source for ranges up to a kilometre. These sources produce signals on standard mine seismic sensors that can be used to measure seismic velocity variations down to 0.01 per cent resolution. This allows the cave progression to be monitored by measuring tiny changes to seismic velocities as the rock above the cave is fractured and destressed.CITATION:Lynch, R A, 2016. Active and passive seismic monitoring of cave front evolution, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Godofredo F. Barrios

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings from as fine as 100 microns and coarser have been used. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies which allow an end user to consider urethane screen surfaces for fine screening applications. These technologies allow an end user to use the inherent advantages of urethane with regards to wear resistance while also realizing the benefits that a high oper area urethane screen surface can bring. These benefits include non blinding characteristics and feed capacities that which rival that of traditional stainless steel surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines they are used in conjunction with. There will also be a presentation of case studies of commercial installations where these technologies are utilized. These case studies are from the base metals industry therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints which must be taken into account when considering urethane screen surfaces such as temperature and chemical attacks. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By S. S. Rowland

Good afternoon, ladies and gentlemen. It is a pleasure, for several reasons, to be here at this 13th International Conference on Ground Control in Mining. Of course it's always a pleasure to be able to see and reacquaint myself with many long-time friends; but it's also a pleasure, or 1 should say worthwhile, because I take something back with me, some knowledge about mining that lets me do my job better and more safely. if I can do that, I've accomplished my purpose in being at a conference such as this. This conference is a little different, though. I have to earn my stay. I have to earn it by telling you a story; a story about mining through a mile of rock to get from one coal seam to the same seam on the other side of an ancient river channel; a story about mine personnel taking over the job from a contractor; a story about having to mine through two faults after the hard part was supposed to be over, but, most importantly, it's a story about how it was accomplished successfully and safely by a group of ordinary coal miners possessed with determination, belief in themselves, and a "can do" attitude. If you can take any part of my story and use it to do your job better and more safely, then I will have accomplished my purpose in being here today. Kerr-McGee Coal Corporation's Galatia Mine is located in Southern Illinois near the town of Harrisburg in Saline County, about 350 miles south of Chicago and 120 miles southeast of St. Louis. Construction of the mine began in 1982, and the first coal was shipped in 1984 from the Harrisburg No. 5 Seam, 550' below the surface. Mining began in the Herrin No. 6 Seam, 100' above the No. 5 Seam, on April 1, 1985. Mining in both seams began by using the room-and-pillar method. In 1989, the No. 6 Seam was converted to longwall mining, as was the No. 5 Seam in 1992. Today, all mining is done by the longwall method except for the required development work, which is performed by continuous miners. A heavy-media preparation plant with a 4.2 million-ton annual clean-coal capacity processes the coal. By the end of 1994, with annual production now exceeding 4 million tons, we will have shipped over 30 million tons of steam and metallurgical coal throughout the United States and the world. Most of the coal has been used as the primary source of fuel to generate electricity for the city of St. Louis. The No. 5 Seam coal can be used as a semi-soft coking coal or as a high-Btu, relatively low-sulfur steam coal. Its use allows utilities to comply with Phase I of the Clean Air Act Amendments of 1990 without installing flue gas desulfurization units or blending with other coals. The Herrin No. 6 Seam is a high-Btu, medium-sulfur steam coal that requires blending to meet Phase I requirements. Because the No, 6 Seam coal does not meet the Clean Air Act Amendments' Phase I compliance standards, we were forced to cease mining operations in the No. 6 Seam, leaving 170,000,000 tons of minable coal in the ground. Last month the Galatia Mine became a single-seam operation mining the Harrisburg No. 5 Seam only. The Clean Air Act Amendments of 1990 and the resultant S02 emission limitations on electrical power generation plants effectively eliminate, beginning in 1995, the near-term potential for profitable mining of the Galatia Mine's high sulfur Herrin No. 6 Seam coal. Because of the Clean Air Act Amendments, it is virtually impossible to market high-sulfur coals like the No. 6 coal unless the mine location and mining conditions enable greatly depressed sales prices to cover costs. We, along with the majority of

Jan 1, 1994

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By Sidney Katell

This report, covering the period January 1966 through December 1966, is a continuation of a series that began with the publication of Information Circular 7516 in October 1944. It is the eighth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering.

Jan 1, 1967

To provide a flexible, low-maintenance, low-cost continuous mine air monitoring system as an alternative to conventional fixed-point, electronic monitoring systems. Background Continuous monitoring of mine air is highly desirable (and often required) not only to improve miner safety, but also to increase mine productivity. Continuous air monitoring systems can provide earl" warning of developing fires, excessive methane accumulation, reduced oxygen levels, and other developing problems in remote, inaccessible or sealed areas, and in active workings. Fixed-point, electronic systems require one Sensor for every gas to be measured at every defined monitoring location. As the number of monitoring locations increases, so does the cost, along with increases in the time required for routine maintenance and calibration of the sensor System cost also increases when monitoring locations are identified for mine areas requiring permissible electrical equipment.

Jan 1, 1988

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By P O. Koons, R J. Norris, S C. Cox

 The Southern Alps is an active oblique collisional zone which has a characteristic wedge-shaped geometry above a low-angle ductile shear zone. The Main Divide region is a relatively low strain zone above this ductile shear zone, and is _deforming principally along steeply dipping strike-slip faults. Extensional fractures are common at a high angle to the regional structural trend. These steeply dipping structures act as conduits for gold-bearing fluids from depth, and small mesothermal gold deposits have formed at several structural levels including the near-surface region. Gold has also been deposited in a meteoricmetamorphic fluid mixing zone near a conductive thermal anomaly on the western slopes of the mountains. These various gold deposits and their well-constrained structural and tectonic settings can be used as analogues for larger, deeper-eroded mesothermal gold deposits in the Mesozoic Otago Schist belt. High level Miocene veins in NW Otago have formed beneath the main divide of the initiating Southern Alps. Late metamorphic gold-bearing veins formed as fluid escaped from the ductile-deforming crustal root beneath Mesozoic mountains.  

Jan 1, 1997

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By J. A. L. Campbell

The Galatia Mine is a dual-seam underground coal mine located in Saline County, IL. In 1984, it became the first coal mine to be permitted by the Illinois Department of Mines and Minerals to operate diesel equipment underground. And it is one of the larger underground coal mines in the nation to use diesel equipment. From the beginning, Kerr-McGee determined that diesel equipment offered the best approach to the safe and productive development and operation of the Galatia Mine. The flexibility of this equipment and its ability to promptly respond to changing conditions and mining locations made its use desirable for building this large dual-seam coal mine. The mine had a planned nominal annual capacity of 3.6 Mt/a (4 million stpy) and would employ more than 500 people. Galatia's current reserves are estimated at 231 Mt (255 million st) of recoverable coal from two seams of high-quality, high-volatile bituminous coal. The Harrisburg No. 5 seam is shipped primarily as a low-sulfur steam coal or as a metallurgical blend stock. It is also used in the pulverized coal injection (PCI) process for steel making. The Herrin No. 6 seam is a medium-sulfur coal. Annual production is shown in Fig. 1. A good indicator of a mine's success is employee productivity improvement. For many reasons - the proper use of diesel equipment, the introduction of longwalls and increased employee ex¬perience - Galatia employees have achieved a steady growth in annual productivity (Fig. 1) while maintaining an exceptional safety record.

Jan 1, 1993

Building the Unified Comminution Model The Unified Comminution Model (UCM) was formulated with the vision of bringing all comminution models onto a common base. The structure of the model relies on knowledge of the mechanical environment in the comminution devices to predict the modes and rates of collision in a device. A detailed understanding of the breakage modes and an ability to correctly test these modes for the ores in question is then required to feed into the UCM. A model structure has been developed that has the capability of dealing with multiple modes of breakage, such as low energy impact surface damage, chipping, sliding abrasion, cumulative impact body breakage and the transition of rock between modes. A critical review is presented on the shortcomings and limitations of utilising the discrete element method (DEM) to provide the mechanical environments. The assumptions and applicability of utilising DEM in milling models are presented and proposed routes to building a realistic mechanistic model are proposed. Based on this more realistic measures of collision energy have been derived from the DEM simulations, which better mimic the real breakage tests. Generic forms of the collision energy distributions have been observed and developed into functional forms for use in the simulation environment. The method of application of this model to a pilot SAG mill is presented.

Sep 13, 2010

By John Lemke

Current practice for monitoring static pile load tests commonly consists of measuring load and displacement at the top of a pile. This is typically accomplished by monitoring dial gauge movements, line pressure of a hydraulic jacking system, and electronic load cells on occasion. While this testing approach provides useful information for one boundary condition (the top of the pile), a system that measures movement and/or strain along the entire length of the pile can provide additional useful data that can be used to refine pile design. Automated data acquisition systems provide the essential ingredient that can integrate these types of sophisticated instrumentation devices into a standard pile load test program in a cost effective way. This paper provides a general overview of pile testing instrumentation and describes a newly developed chain of instrumentation modules that can be embedded in a pile to gather additional testing information. The new system can measure forces and movements within the test pile synchronously with measurements at the pile top, and the direct application of this system to axial and lateral pile testing is illustrated. This is particularly relevant to the design of ACIP and drilled displacement piles since determination of the reinforcement cage length is important from the standpoint of both seismic design and foundation cost.

Jan 1, 2002

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019

By P M. Ashley, M Muller

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of north-eastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe land sliding in previously mined areas. Mining from the 1890s to the 1960s has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

By Richard E. Gertsch

If you believe that the goal of the space program should be a permanent, manned presence in space, then you believe in space mining. Historically, mining has been an integral part of the frontier. For the space frontier, mining is absolutely necessary. Any large-scale space facility must be built from materials mined in space. The reason is simple: the cost of getting material off the earth overwhelms all other costs. The cost of launching a pound of material from earth into low earth orbit ranges from $5000 to $10,000. Multiply this number by three to get to geostationary orbit. With the added expense of landing on the moon, an object is worth more than its weight in gold. Most space projects are impossible if materials must be hauled out of earth's enormous gravity well. For example, habitats (large structures in free-fall that simulate earth's gravity) and massive solar power satellites will take millions of tons of material to construct. Transportation economics alone dictate space as the source for oxygen, construction materials, and metals, among others. Space mining is not concerned with introducing materials for terrestrial use. The need for materials in space is infinite. The challenge for the mining industry is enormous.

Jan 1, 1991

By M. K. Quinn, N. P. Reddy, A. W. Khair

"An analysis of coal fragmentation due to the action of a continuous miner is presented. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). The rotary coal cutter provided the versatility of varying the operating and in-situ parameters to provide information on the effects of generating 37 pm (0.0015 in) particles. In these tests, coal blocks with an approximate dimension of 50.8 x 35.6x 20.32 cm (20x 15x 8 in) were first subjected to confining pressures equivalent to in-situ conditions. The blocks were then cut by the rotary cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as (1) penetration of bit into coal, (2) penetration resistance (thrust and cutting pressures), (3) rotating velocity of' cutting head, and (4) acoustic emission activity in the coal block were monitored. During the test, all the cut products were collected for size distribution analysis. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using a camera attached to an optical microscope.The results led to a better understanding of the mechanisms of the fragmentation process during coal cutting and the effect of operating parameters, in-situ conditions and coal type on the size distribution of the cut product:"

Jan 1, 1989

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By W. P. Yant, R. R. Sayers, H. W. Shoaf, John Chornyak

"The contemplated use of dichloro-difluoro methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for Public buildings and possibly homes, brings attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorine compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines was requested to make a laboratory study of the toxicity and potential hazard:"" and it was on the basis of the results of this work and the results of a preliminary investigation made in another laboratory5 that the compound has been selected for commercial use. Although the investigation conducted by the Bureau of Mines is still in progress, information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:Additionally work rich is in progress at the present time includes a determination of the lethal time-concentration curve for animals and a study of the response of persons within the range of safe concentrations.The writers desire to jive acknowledgment to T E. Midgley, Frigidaire Corporation, Layton, Ohio, for suggesting the investigation, for arranging for the cooperation of the Frigidaire Corporation, and for advice during the experimental work; to Robert A. Kehoe, The Eichberg Laboratory of Physiology, University of Cincinnati, Cincinnati, Ohio; and E. R. Hayhurst, college of Medicine, Ohio State University, for consultation and advice in planning the work; and to the following employees of the Bureau of Mines for assistance in performing the experimental work: L. M. Berger, chief scientific aid, S. J. Pearce, junior chemist, and Ethel B. Stead, technician."

May 1, 1930

By F. Khomamizadeh

In this study the effect of solidification rate, T6 and T7 heat treatments on thermal fatigue resistance of A319 aluminum was investigated. Increasing of the solidification rate improved the thermal fatigue resistance of the alloy by refinement of the microstructure. The most sensible areas for thermal fatigue crack growth were the eutectic zones, T6 and T7 heat treatments improved the thermal fatigue resistance of the alloy by enhancing of the matrix resistance against the crack propagation. The slight reduction of the thermal fatigue resistance after T7 heat treatment is attributed to coarsening of the precipitates which reduces the matrix resistance.

Jan 1, 2005