Search Documents

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By R. Filippone, Donald Leroux, Colin Hardie, G. Leichtle, Cesar Gomez, Jim A. Finch

"Bubble surface area flux (Sb) is the surface area of bubbles per unit time per unit cross-sectional area of flotation machine. The units are: (m2 bubble surface/s)/(m2 cell) or s -1. For bubbles of mean size db (m), s b = 6-Qg/A db where Qg is the gas rate (m3/s), and A the cell cross-section (m'). This parameter is now receiving wide attention as the possible key machine variable in flotation diagnosis and modelling. The concept is described and the potential use of sb is illustrated by work on flotation columns and mechanical cells. In column flotation of recycled paper, the dependence of ink recovery on s b was the same regardless of size of column or type of sparger. In mechanical cells, it has been established that the rate constant is related to Sb independent of impeller type.The use of s b is limited by the problem of measurement, primarily that of estimating db. A prototype probe designed to estimate db (and hence sb) based on conductivity measurements is described. Exploratory work with the probe in a mechanical cell suggests the promise of making estimation of s b routine.INTRODUCTIONFlotation is the result of interaction among variables associated with the feed particles, chemistry and the machine (flotation cell). Trying to isolate the effects of each aids in process diagnosis and is at the centre of attempts to model flotation. The machine variables that have been investigated include the air flow number, the power number and specific power (Harris, 1976). None have survived as the basis for predicting flotation response perhaps because they did not include directly the properties of the bubble swarm (or dispersion). Recently, Gorain (1 997) explored the relationship between the flotation rate constant and various ""gas dispersion"" parameters notably: superficial air rate (Jg = Qg/A, where Qg is the volumetric gas rate and A is cross-sectional area of cell), bubble size (db), gas holdup (Eg, i.e., the volumetric fraction of a cell occupied by gas) and bubble surface area flux (sb = 6.Jg/db). Of them all, Gorain et al. (1997) conclude that the latter, the surface area flux, correlated best with the flotation rate constant. This concept was adopted from column flotation where it was used to estimate, among other factors, the maximum amount of gas that could be injected (Finch and Dobby), 1990). Let's start by reviewing the concept. Following that some examples of where the concept has been applied will be described to illustrate the current interest and finally we will consider how to measure the surface area flux."

Jan 1, 1999

By B. Ulrich

The basis of this paper is a compilation of work in the design and construction of copper heap leach facilities, and interviews with various heap leach operations personnel in Chile and Peru. The purpose is not to highlight specific mines and their performance, but rather to discuss geotechnical/civil features of copper heap leach facilities that function well, as well as features that do not. During the 1990s several copper heap leach facilities were brought on-line in South America. Many of these facilities have now been operational for a number of years during which time the operators have been able to monitor the performance of their heaps. This paper serves as a compilation of operators? experiences, and provides a discussion of the lessons learnt over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of inter-lift liners. This conference provides a timely update of the original paper (Burkhalter et al, 2002).

Jan 1, 2003

By H. Preßlinger, H. Hiebler, K. Klepp, W. Posch, M. Mayr

It was investigated in which form sulphur is bonded in ladle slags. For this purpose, the mineralogical phases of the ladle slags were qualitatively and quantitatively evaluated by means of a microprobe. This slag characterization allowed reconstructing the bonding of sulphur into the phases of the ladle slag. Moreover, the reaction process with regard to the ionic theory as well as the structural formula for the mechanism of sulphur bonding were discussed. The bonding of sulphur into calcium aluminate slags is determined by the sulphide ion content in the slag as well as by the ratio of (CaO)/(Al2O3). Calcium sulphide separates only if the slag contains a large number of sulphide ions. When Ca12Al14O33is separated, the sulphide ion is successively integrated into the lattice. The crystal lattice of Ca12Al14O33is characterized by an open, three-dimensional anionic network composed of aluminium-oxygen tetrahedrons linking the edges. In this network, large interstitial spaces are formed, which may be filled with calcium ions on the one hand and statistically with a free oxygen or sulphide ion on the other hand. Key Words: ladle slag, structure, phases, calcium sulphide, calcium aluminate, desulphurization

Jan 1, 2004

By F. T. Cawood

This research report was produced in response to the release of the Mineral and Petroleum Royalty Bill. It involved are view of the mineral investment environments of selected countries in order to form an opinion on the appropriateness and competitiveness of the proposed royalty structure for South Africa. Many emerging countries have recently attracted a significant share of foreign investment, as a direct result of changes in policy. These are, by implication, the least risky and most favourable destinations for the ?investment dollar?. The five most competitive countries, namely Chile, Argentina, Peru, Mexico and Brazil have been identified as succeeding with their policy visions of creating favourable domestic investment environments. The investment rules of these countries served as a basis for the compilation of a Competitive Investment Framework (CIF). This is a template of best practice against which other investment environments, such as that of South Africa, can be measured. The framework indicates that mineral royalties should ideally be no more than three per cent, demonstrating that the regime proposed in the Royalty Bill is out of step with international best practice. Mineral royalties can never be viewed in isolation and in the assessment of the rates proposed in the Royalty Bill, one must consider the total taxation package. Such assessment appears in Section 5 of this report, demonstrating that there is reason for concern if National Treasury were to impose the rates stipulated in the Royalty Bill. The alternatives, conclusion and recommendations of the review appear in Sections 9 and 10. These are the result of independent analysis and assessment of the fundamental principles. It is done through the application of a Competitive Investment Framework that avoids the highly subjective and emotional views that often accompany a process like this.

Jan 1, 2003

By P. I. Page

In mineral exploration the place that yields the first significant result is marked and two questions are posed immediately. Where should the next sample be drawn and how big should it be? At present the answers are arbitrary and ad hoc. They depend on personal experience and sentiment?that is hunch. The thought processes involved in reaching the decisions are unsatisfactory and unsatisfying for professionals. This paper proposes guidance on choosing sample spacing and sample size. The guidance is obtained from the grades of the samples. The grades also imply the extent of influence of each sample assay. Thus sampling and assay are integrated. The integration is achieved by changing the unit of value in which assays and grades are expressed and by exposing meanings and functions of grade beyond that of measuring rock value. The proposals are extended to guide comminution of particle size in sample size reduction and to deal with the problem of erratic high assays. Also, elucidation becomes possible of the computation of a reliable figure for average grade as a statistical weighted mean.

Jan 1, 2005

By G. A. Kordosky

The concept of selectively extracting copper from a low-grade dump leach solution followed by stripping the copper into an acid solution from which electrowon copper cathodes could be produced occurred to the Minerals Group of General Mills in the early 1960s.This simple, elegant idea has resulted in a technology by which about 2.2 million tonnes of high quality copper cathode was produced in year 2000. The growth of this technology is traced overtime with a discussion of the key plants, the key people and the important advances in leaching, plant design, reagents and electrowinning that have contributed to the growth of this technology. Some thoughts on potential further advances in the technology are also given.

Jan 1, 2002

By R. Gallinger

In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale. The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP?s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP

May 1, 2005

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits, thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium. Key Words: Rhenium, Ammonium Perrhenate, Extractive Metallurgy

Feb 27, 2013

By T. J. Ballard, Austin B. Clayton

"The Union Copper mine is in the Gold Hill district, Rowan and Cabarrus Counties, N. C.The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907.As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes, totaling 2,500 linear feet, were drilled to delineate the ore body. Analyses of 205 core samples were made.Tabulations of sample analyses and drill-hole logs are presented in this report.The project work embodied in this report was under the immediate supervision of Austin B. Clayton, project engineer, and the general supervision of H. B. Ewoldt, district engineer for North Carolina and Tennessee. The preliminary report, written by Austin B. Clayton, was revised and the various figures redrawn for publication by T. J. Ballard under the general supervision of M. H. Kline, chief, Raleigh Branch, Mining Division.Acknowledgment is due the Metallurgical Branch for analytical determinations of the samples.The mine property is 1.5 miles southwest of the village of Gold. Hill, N. C. (fig. 1). Gold Hill is on U. S. Highway 52 between Salisbury and Albemarle and on a branch line of the Southern Railway. The latitude is 350 30' and longitude 80° 21 The tract consists of 553-1/2 acres in Cabarrus and Rowan Counties.A tentative list of the surface-rights ownership is as follows: William Hoy Barringer - 16 acres, A. W. Tucker - 1 acre, Frank Wagoner - 4 acres, and George Barringer - 3-1/2 acres, in Cabarrus County; A. W. Tucker - 2 acres, H. N. Hedrick - 54 acres, and William Atkins - 473 acres, in, Rowan County, N. C.The mineral rights are owned by Alfred Rossiter, Alice R. Hesslein? and the estate of the late Bella Rosenblatt. The attorneys for the owners are Neidle & Taylor, 6 East 45th Street, New York City.The Union Copper mine is in the Cold Hill mining district of North Carolina where gold was first discovered in 1799. The upper parts of the veins in the district were first worked for gold; however, the increase in the sulfide content of the veins with depth rendered the amalgamation process for gold recovery ineffective, and the mines were closed.The period of greatest activity at the Union Copper mine was from 1899 to 1906. At an earlier period the oxidized and leached part of the lode near the surface was mined from a working known as the ""big cut,"" the reported yield of which was $300,000 in gold.3/ The mine has not been operated since 1907.J. T. Pardee3/ lists the probable value of the production of the Union Copper mine as $1,050,000, of which about $675,000 was the value of some 5,000,000 pounds of copper produced."

Oct 1, 1948

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

The Golden Cross project was a joint venture between Coeur NZ Ltd (80 per cent) and Viking Mining Company (20 per cent). The site is located in the Waitekauri Valley, 8 km north-west of Waihi, on the Coromandel Peninsula, in the North Island. The mine-site is situated close to the Coromandel Range Divide between the headwaters of the Waitekauri River and the Martoto Stream. The site has a history of Gold Mining dating back to 1892. The more recent mine comprised an open pit and underground gold and silver operation from December 1991 to April 1998, MacGillivray, Maton and Goldstone (2000).Doug Hood Ltd commenced the first of three contracts on site in September 1997 and was responsible for completing the final stages of open pit mining, landslide remedial works mine closure and rehabilitation works. The Mill Closure and Rehabilitation and Drainage Works contract, for which this submission relates, commenced in September 1999 and was officially completed by Doug Hood Ltd. on the 26 May 2001.This paper endeavours to highlight the project objectives and backgrounds them against the difficulties experienced with respect to the site-specific conditions, the design complexities and risks associated with the contract, from a contractorÆs perspective.

Jan 1, 2002

By Ralph H. Whaite

In undermined urban areas, new solutions to subsidence problems are being sought. The Bureau of Mines is investigating a hydraulic backfilling technique whereby fill material is pumped as a slurry through a closed system and widely distributed in inaccessible mine workings from a single borehole. A full-scale demonstration was completed in 1973 in Scranton, Pa., which is underlain by abandoned anthracite mines in several coalbeds superposed one above another. A 30-acre residential area was stabilized by injecting about 450,000 cubic yards of crushed mine refuse into two coalbeds through five injection boreholes. Nearly 200,000 cubic yards was injected through one borehole from which the material moved into the mine workings on all sides; the injected material reached a maximum lateral distance of 640 feet and filled mine openings from floor to roof. In the gravity-feed method formerly used to backfill inaccessible mine workings, quantities of fill injected per borehole averaged about 300 cubic yards. The gravity-feed method required many closely spaced injection holes and provided incomplete filling. The new method, designed for inundated mines, proved successful also in mine workings about mine-water pool level. Distribution of slurry through a buried pipeline minimized disturbance to the community.

Jan 1, 1975

By Marc Legault

The Duparquet mining camp situated along the Quebec segment of the Porcupine-Destor Fault was the site of gold exploitation from 1933 to 1956 and 1988 to 1991. Numerous gold showings and deposits straddle the fault. An ongoing regional metallogenic study by the Quebec Geological Survey has identified five main types of gold mineralization, each showing a distinct style, alteration, control, metal content, and timing. In order to maximise the impact of this study, a 3D regional common-earth-model was constructed along a critical segment of the Porcupine-Destor Fault with the gOcad® technology. The realisation of this model required the maximum use of the public SIGEOM numerical database, as well as the recovery of significant private data from exploration company partners. The 3D model is also a powerful new dynamic exploration tool, which can be queried using geological criteria characteristic of the different gold deposit types. This 3D model can be modified and improved continuously by adding data from new drilling, mapping or geophysical surveys. The case of the Porcupine-Destor Fault illustrates the importance of 3D common-earth-modelling in delivering refined technological geological syntheses likely to attract significant investments from the mining exploration industry, especially for deep exploration programs within mature mining camps.

May 1, 2004

By R. S. Dean

This report, the second of a series of annual reports of the Metallurgical Division to be released in this form covers the fiscal year July 1, 1935, to June 30, 1936. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

Nickel-bearing ores in North-east Dundas have been described by A. McIntosh Reid1 as occurring at the margins of narrow dykes of gabbro, norite, peridodite and pyroxenite, which are intrusive into the Dundas series of slates, quartzites and breccias. They occur chiefly in the neighbourhood of the Five Mile, near Zeehan, as small, narrow ore-bodies which are mostly less than 100 ft. in length.The ores are massive sulphides containing pyrrhotite, chalcopyrite, pyrite and the nickel sulphide, pentlabdite.A less common nickel-bearing mineral, gersdorffite, has been recently found in an adit, which is marked on Reid's geological plan of Dundas as the Hecla mine, 30 chains south of the crossing of the North-east Dundas tramway, over the Great Northern Creek, and at an, elevation of about 350 ft. above the tramway. The occurrence is in a lode traversing the Dundas slates and quartzites, and is situated, according to Reid's plan, about 20 chains beyond the northern extremity of a narrow basic dyke which is continuous for a distance of two miles in a south-westerly direction.The mine eonsists of a prospecting adit following the course of a lode for about 275 ft. in a direction a little west of south. The low values of the lode are indicated by a bulk sample from a shallow winze about 100 ft. from the entrance which is reported by Reid to contain:

Jan 1, 1935

By R. S. Sanford

The Claim Point chromite deposits are at tidewater near the southern tip of the Kenai Peninsula in southwestern Alaska, The United States Geological Survey had a field party in the region from July until September 1940 under P. W. Guild, assistant geologist; maps and geological data were assembled and made available to the Bureau of Mines. A preliminary investigation of the deposits at Claim Point by the senior author during July 1941 was followed by surface sampling and core drilling to determine the quantity and grade of the ere, The Geological Survey was represented at the project by George O. Gates, geologist. Cores were checked and the structural data revealed by drill cores were interpreted. The principal chromite deposits have been sampled and delimitated by trenching and core drilling. Other deposits were trenched and sampled but were too small or too low-grade to warrant core drilling.

Jan 1, 1949