Search Documents

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

The poor reconciliation between the values of estimated and actual grades can cause major economic losses to the mining industry. In a mining operation grade reconciliation is comparing the values of estimated grade calculated in exploration stage with actual grade obtained from blastholes' data. Many different factors affect the degree of reconciliation in a mining operation. In this paper we investigate the factors related to estimated grade which affects the reconciliation process in the exploration stage of the orebody. These factors are the sources of uncertainty in the rest of mine life. In this area the most important factors are inherent variability, statistical uncertainty and systematic uncertainty. A probabilistic model was presented to model each source of uncertainty. The implementation of proposed model was checked and its validity was investigated using real data in an iron open pit mine in Iran.

Dec 6, 2010

Various reagents are added to flotation pulps to manipulate the chemical environment in order to create favourable conditions for the separation of the desired mineral from the unwanted gangue. Interactions occur between these reagents and between the other chemical parameters existing in the flotation pulp which complicate the elucidation of the behaviour of the respective reagents. This paper discusses the roles of the main classes of reagents added viz. collectors, frothers, depressants and activators, as well as the interactions between frothers and collectors. A case study reporting synergistic interactions between thiol collectors in the flotation of pyrite at pH = 4 is included. The use of Potassium n-butyl xanthate (PNBX) and a dithiocarbamate type collector (DTC) were tested both as pure collectors and as components in a collector mixture. In the batch flotation tests sulphur recovery and grade, water recovery, rate of recovery and image analysis of the surface froth were used to evaluate the effect of the mixture on the overall flotation performance. Bubble loading tests showed that the use of the mixture improved the efficiency of the particle collection process by bubbles. Thermochemical measurements of the adsorption of the collectors onto the mineral, indicated the formation of different surface products by the two collectors.

Jan 1, 1998

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By Ross W. Smith

Microflotation and surface chemical studies were conducted on a chromite from the Stillwater Complex in Montana and on some of the minerals usually found to be associated with such chromites. Considering the chromite it was found that aging the ground mineral in air or heating it markedly affected its flotation behavior. Much of the observed effects could be attributed to oxidation reactions involving surface chromium and iron species. Strongly acid pretreating the mineral appeared to reverse such effects. Thus, it can be concluded that the manner in which the mineral (or the ore) is pretreated is of utmost importance in its flotation. Work carried out on associated gangue minerals determined how they are likely to behave in a flotation environment and how certain foreign ions derived from a chromite ore itself can affect their surface characteristics and, thus, presumably also their behavior in a flotation circuit.

Jan 1, 1981

This paper focuses on two sites in the Mount Pleasant - McCormacks Bay area of Christchurch where residential development has taken place either within or immediately adjacent to former quarries for the extraction of volcanic rock. At the Quarry Road site less overburden was dumped on adjoining land around the turn of the century, and c.1980 dwelling and related construction took place on approximately 6 m of relatively loose fill material without the recognition of its presence or geotechnical characteristics. Subsequent settlements led to abandonment of a swimming pool and the underpinning of the 3-storey architect-designed house, whilst litigation brought by the owner resulted in findings of negligence against both the architects and engineers. At the Tramways Quarry site the Council approved subdivision of the former quarry area in the early 1980s without requiring any geotechnical evaluation of batter stability or related issues. During development it became apparent that significant blast damage had occurred to rock faces, necessitating a variety of remedial measures, and that waste materials had been dumped down faces without regard to long-term stability. Both case studies confirm the requirement for careful documentation of former quarry sites by territorial local authorities as part of their administrative function, and for detailed engineering geology and geotechnical evaluation of such areas prior to any residential use of the land.

Jan 1, 1998

By R Brake

The Enterprise Mine (EM) is located at Mount Isa and is wholly owned by Mount Isa Mines Limited (MIM). This high-grade copper mine extends from about 1000 m below surface to almost 2000 m below surface. A recent $400 million upgrade has taken the operation from a production rate of 1.3 Mtpa to a capacity of 3.5 Mtpa. The effects of high surface ambient temperatures in summer, combined with the depth of the mine and high virgin rock temperatures results in heat stress in the working place that, without intervention, would exceed the levels that human physiology can withstand. It would also result in significant decreases in productivity and high accident rates even where work is possible. Moreover, with a very hot and deep mine, the needs of æegressÆ and entrapment of workers during a mine emergency must be carefully considered. Enterprise Mine has taken a æsystems approachÆ to the issue of working productively, healthily and safely in heat. This involves setting limits of thermal stress for workers, understanding productivity decrements when working in heat, establishing productive and healthy environmental targets, developing engineering solutions to meet these targets, creating a well-educated workforce with respect to working in heat and then developing health protocols to ensure workersÆ health is protected. Refrigeration must be added to the mine to provide acceptable and productive conditions underground. By the time the mine is commissioned in 2000, Enterprise mine will have an installed refrigeration capacity of in excess of 40 MW(R). The ventilation engineering principles proven over many years at the other Isa underground mines are tailored to æfloodingÆ the mine with air to remove the heat, which is the main contaminant. This principle will not work at the Enterprise Mine, for reasons discussed below. With the underlying ventilation principle no longer satisfactory, a complete review of the entire ventilation principles and engineering solutions was required for the Enterprise Mine.

Jan 1, 2000

By S. du Plessis

Nationalization is high on the policy agenda in South Africa. This paper considers the case for nationalizing the local mining sector from an evidence-based perspective, which is derived from theoretical considerations and related to the known features of the South African mining sector and economy. A strong case against nationalization emerges, which can be summarized as follows. The mining sector is competitive and therefore a poor candidate for public ownership. Furthermore, the resources sector does not dominate the South African economy nor does it create the risk of a decrease in the competitiveness of the industrial sector via the unintended adverse impact of an appreciating real exchange rate due to a commodity boom (Dutch Disease). Nationalizing the mining sector will cost the government more than it receives. This is not only a bad idea in itself, but it will limit the scope for distributive policies on the national budget. The contemporary international experience demonstrates the risks of fiscal imprudence. Finally, nationalizing the resources sector will undermine support for those very market-based institutions required to achieve a higher long-run growth trajectory.

Jan 1, 2013

By Y. Chengxian

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By William Gleason

"The times they are a changing, and, for the mining industry, the optimism is high. On Nov. 8, Donald Trump was elected as the 45th president of the United States, and the Republican Party won a majority of seats in the U.S. Senate and the House of Representatives, ushering in what many hope will be a positive change for the mining and extractive minerals industries.Trump has stated that one of his top priorities as president will be to increase spending on the nation’s infrastructure, which could help spark a boom for mining. He has also pledged to bring back coal jobs and reverse many of the environmental regulations that were put in place by the Obama administration. However, before the mining industry gets too far ahead of itself and plans for another Super Cycle, there are stark reminders that any work in the natural resources sector is complicated and challenging. On Dec. 4, the U.S. Army Corps of Engineers announced that it would not grant an easement that would allow the Dakota Access Pipeline to pass under a portion of the Missouri River in North Dakota. The proposed crossing of the oil pipeline is approximately a half a mile upstream from the Standing Rock Sioux’s Reservation, and for months, hundreds of protestors camped out at the site in an effort to halt the project, saying they feared how it would impact water supplies and sacred lands.Energy Transfer Partners, the company building the pipeline, said the pipeline is a $3.78-billion investment that will connect the Bakken and Three Forks production areas to major refining markets. The company signed voluntary easement agreements with landowners representing more than 85 percent of the properties along the four-state route but faced an organized protest from the Sioux Nation at Standing Rock. The protest gathered momentum and support through social and traditional media and became the focal point of global environmental and indigenous activism. The protestors claimed victory, at least temporarily, when the Corps of Engineers said it would look for alternative routes for the project. It’s a decision that could lead to a lengthy environmental review and one that has the potential to block the construction of the pipeline for months or even years."

Jan 1, 2017

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

By L Reynolds

Oceana Gold (New Zealand) Limited (OceanaGold) has commenced mining operations at the Globe-Progress mine in the Reefton Goldfield, an area that historically produced 2.1 million ounces of gold from underground quartz lode deposits. During the construction phase of the operation, advanced exploration programmes targeting near-mine prospects commenced. The focus of this ongoing exploration is the discovery of near surface, refractory gold deposits that are amenable to open-pit mining methods and treatment through the Globe-Progress process plant.   One such discovery is the Supreme deposit, located along strike approximately 3 kilometres to the south of the Globe-Progress mine. The Supreme area was tested extensively with diamond drilling in 2006, defining a deposit with similar mineralisation styles and grade to the Globe-Progress deposit. The mineralisation comprises a central core of gold-bearing quartz veins, locally containing visible gold, surrounded by a more extensive halo of refractory, disseminated gold associated with an arsenopyrite-pyrite sulphide mineral assemblage. Three subparallel mineralised structures host the mineralisation. These structures are highly oblique to the country rock orientations, extending approximately 250 metres along a northeast-southwest strike and at least 220 metres down-dip, with an average thickness of 12 metres and moderate dip to the southeast. Records of historical workings indicate that mineralisation extends further down-dip and remains open at depth. 5175 ounces of gold were mined historically at the Supreme deposit. OceanaGold have defined an Inferred Resource for the Supreme deposit of 0.84 million tonnes at 1.46 grams per tonne for a total of 40 000 ounces (at a 0.8 grams per tonne cut-off). Higher-grade zones of mineralisation exist within the deposit and further drilling is planned to test the extent, continuity and geological controls of the mineralised structures.

Jan 1, 2007

By U König, N Norberg

To cope with varying raw material qualities and increasing prices for energy, a more frequent and accurate monitoring of the processing of iron ore became the focus in sinter plant operations. Traditionally, quality control in iron producing industries has relied on time-consuming wet chemistry or the analysis of the elemental composition. The mineralogy of a sinter that defines the properties and behaviour in the blast furnace is often not frequently monitored. One fast method to analyse the mineralogical composition of iron sinter, raw mixtures and iron ores is X-ray diffraction (XRD). Recently statistical methods such as similarity analysis or partial least square regression (PLSR) in combination with XRD raw data has become more and more popular in handling large amounts of data and correlating process-relevant parameters directly with an XRD measurement. PLSR can be used to correlate process parameters directly from the XRD pattern without investigating the mineral content. Hidden information that is present in the measurement but not determined with traditional methods can be used to improve the characterisation of the analysed materials.CITATION:König, U and Norberg, N, 2017. Iron sinter process control using X-ray diffraction – part : monitoring of low temperature degradation, in Proceedings Iron Ore 2017, pp 75–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

By P Minkkinen, J Lohilahti, T Korpela, B McPherson

Concentrator plants intake the ore from the mine and produce concentrates by extracting valuable minerals in a succession of process steps. Controlling the extraction process and detecting changes in the process requires updated information on a minute basis. Moreover, due to economical reasons, one must also collect metallurgical samples on a daily basis for monthly reporting.In this paper, we present how slurry samplers were installed in a Cu-Ni flotation plant to accomplish the aforementioned tasks. An on-stream elemental analyser at the plant is used for flotation process control by taking samples from selected process streams. Two process streams, the flotation feed and tail, are also equipped with metallurgical samplers. The metallurgical samplers were designed to have low head loss, be robust and easy to maintain and to collect slurry samples in a reliable way for the metallurgical accounting.Samples were collected by different sampler types and we discuss the uncertainty arising from sampling in the assays. Variographic analysis was carried out on the process data in order to find periodic components in the process, and estimate the correct number of shift sample increments and measurement error components. The metallurgical samplers were proven to be reliable devices with zero downtime and no sanding issues in the main process flows. In addition, we show that the tail measurement is the most important one for the plant recovery calculation, which emphasises the importance of the sampling accuracy in the tail stream.CITATION:Lohilahti, J, Korpela, T, Minkkinen, P and McPherson, B, 2014. Analysis of slurry sampling arrangements at a froth flotation plant, in Proceedings Sampling 2014 , pp 91–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By Francis T. Freeland

In the West many precious-metal mines are worked in patches by lessees, under conditions which closely resemble those of what is called " tribute-work" in Cornwall.* The company has its own foreman or inspector, and usually employs the engineman, blacksmith, pumpman, and perhaps other general workmen. As an inducement to work on a new piece of ground, where no ore is in sight, the company may advance a " footage"

Jan 1, 1896

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013