Search Documents

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By D. Kruse

Top down constructed large diameter (up to 90 m [300 ft]) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to: analyze various failure modes, evaluate the shaft liner and internal structures? response to seismic loading, assist in segment design, and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly, and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored.

Jan 1, 2011

By J. T. Dunham

The Bureau of Mines studied by dilatometry the effect of titanium on the thermal expansivity of hot-rolled zinc and Zn-l percent Cu alloy. The titanium content of the alloys was varied up to 0.3 percent. Expansion coefficients were determined from measurements made both parallel and perpendicular to the plane of the rolled sheet. Titanium reduced expansion parallel to the plane of the sheet, especially in the rolling direction, but increased expansion perpendicular to the sheet. Basal-plane pole figures showed that the degree of preferred orientation increased with the titanium content in the alloy, and that anisotropic expansion can be correlated to sheet texture.

Jan 1, 1965

In all the industries that require blasting operations using explosives, there exists numerous unwanted side effects of the blast which may pose as environmental hazards. These hazards face prominence, especially in India, where there are very stringent rules and regulations governing the use of explosives. The environmental hazards associated with blasting operations as a whole can be tacked successfully to a certain extent depending upon the ultimate expectations of ,the post-blast effects and the limitations of the environmental obligations as specified by the authorities from time to time and from place to place. The main parameters which require attention to limit the post-blast results to the optimum level are ground vibrations, dust pollution, gas pollution, air blast effects, noise pollution & fly rocks etc.

Jan 1, 1995

By Noel N. Moebs

The U.S. Bureau of Mines is conducting research on many topics relating to the mineral resources of the United States. This is done to ensure an adequate supply of minerals essential to a viable domestic industry and a sound economy. The United States is almost totally dependent on foreign supplies for a number of minerals such as chromium, niobium, tantalum, and manganese for which there is no available substitute, while many other minerals such as titanium are abundantly distributed throughout the earth but seldom occur in adequate concentrations or useful forms. This report describes an example of a small but high-grade occurrence of titanium are in Nelson County, VA. This occurrence could be exploited under favorable economic conditions with new mining technology such as borehole slurry mining. The report demonstrates that the dikes at titanium ore, a mixture of ilmenite and apatite locally termed nelsonite, can be detected and traced along strike using magnetometer traverses. This information will aid in the selection of appropriate slurry borehole mining test sites in the area.

Jan 1, 1993

By L. Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m, while the length of the panel is changed between 1,000 to 2,000 m. The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Clair Murdock, David Heath

The 1,280 MW Sir Adam Beck II Hydroelectric Project was constructed in the1950s, at Niagara Falls, Ontario, Canada. The twin intake tunnels total over 17 kilometers in length and pass deep below the City of Niagara Falls. The tunnels were excavated using drill and blast methods, with a top heading and bench approach. The shot rock was loaded with electric shovels and transported to the five shafts with off-highway trucks. The tunnel muck was hoisted to the surface by skip and transported by truck to disposal areas. The volume of underground excavation for the 15.55 meter diameter tunnels and the shafts exceeds 3,500,000 cubic meters, then and now the largest underground civil works excavation by drill and blast in the Western Hemisphere. The lining required over 900,000 cubic meters of concrete. All of this work was completed in three years, remarkable progress, considering the technology of the day, comparing very well with the rapid excavation and tunneling methods of the twenty-first century. Big, fast, and deadly—at least 20 lives were lost in construction accidents.

Jan 1, 2007

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By J. H. Swisher

An experimental study has been made of the possible mechanisms for foam stability in the system CaO-SiO2-Cr2O3, where Cr2O3is the foaming agent. The degree of lowering of surface tension by Cr2O3 was determined at 1600 "C for high -silica melts. Measurements were also made of foam stability under standardized conditions. The results of the two sets of measurements then were correlated by applying the Gibbs and Marangoni theories of film elasticity. It was demonstrated that the Marangoni elasticity effect is probably the largest single contributor to foam stability, although the high uiscosity of' silicate melts makes some contribution in controlling the rate of drainage of liquid from bubble lamellae. ThE tendency of metallurgical slags to foam has frequently been observed during steel-refining operations. In the open-hearth furnace,this tendency is considered undesirable because it slows down the rate of heat transfer from the burners to the molten-metal bath. On the other hand, it is sometimes desirable to have a "foamy" slag in the basic oxygen converter.' A more effective blanket over the steel bath is made by a "foamy" slag, and loss in yield of metal due to splashing is minimized. In addition, a flush slag can be removed more easily in this condition. Since slag-foaming problems in the field have been attacked largely on an empirical basis, it appeared desirable to obtain a better basic understanding of the mechanism of foam stability. The experimental work was directed almost entirely toward the behavior of Cr2O3 as the foaming agent in CaO-SiO,-Cr2O3 melts. In the first stage of the investigation, the degree of lowering of surface tension by Cr2O3 was determined at 1600°C. The second stage consisted of measuring foam stabilities under standardized conditions. The two sets of experimental results then were correlated by applying various theories of foam stability. For convenience in interpreting the surface-tension and foam-stability results reported here, a portion of the CaO-SiO2-Cr2O3 phase diagram2 is reproduced in Fig. 1. EXPERIMENTAL 1) Surface-Tension Measurements. Very little information is available in the literature on the lowering of surface tension of slags by foaming agents. Kozakevitch 3 mentioned that the addition of 1.5 pct Cr2O3 lowered the surface tension of FeO slightly. In another system, some data on the lowering of surface tension of foaming slags by P2O5 were reported by Cooper and Kitchener.4 The technique used for the surface-tension measurements was the maximum bubble-pressure method,' using a single tube immersed to various depths in the melt. This method has been used extensively in high-temperature systems, such as in liquid metals, slags, and glasses.6,7 It has the advantage that the contact angle between the liquid and the tube material need not be known. The equation used for calculating surface-tension values from maximum bubble-pressure measurements is the Schroedinger equatioq5 which can be written as follows:

Jan 1, 1964

By V. E. Edlund

As part of a research program for recovering alumina from domestic nonbauxitic resources, the Bureau of Mines investigated a lime-sinter, caustic leach technology for anorthosite. This report discusses the unit operations--feed preparation, sintering, and leaching. Acceptable pellets for the bench-scale sintering studies were prepared from mixtures of minus 200-mesh anorthosite and limestone using water alone as the pelletizing agent. Heating pellets at 1,270° to 1,360° C for periods of 0.5 to 2 hr, followed by a 15-min soaking period at 700° C and cooling to room temperature, produced a sinter that dusted to more than 90 pct minus 65 mesh. The weight ratio of limestone to anorthnsite was critical in producing sinter exhibiting good dusting and leaching characteristics. A ratio of 2.0 was optimum for the bulk samples of anorthosite and limestone used in this research. Leach solutions from lower ratio sinters were unstable; gelation became progressively more severe with higher ratio sinters. Leaching the dusted sinter with 10-pct Na2CO3 at 60° C extracted 85 to 90 pct of the alumina in a product solution containing about 50 g/l A1203. Leach residue in contact with pregnant solution tended to set up as a rigid gel as a result of cementation, comp action, and gelation. The presence of a calcium-sodium zeolite [(Cn,Na2)6?(Al2Si04)12?27-3OH20] in the ungelled residues seemed to be the main difference between gelled and ungelled residues.

Jan 1, 1982

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By C Adams

Reports of delays and cost blowouts in major study and construction projects are becoming increasingly prevalent in the resources industry. This is mainly being attributed to an escalating cost environment associated with the increased number of projects in the development to construction pipeline and a scarcity of competent skilled resources to deliver these projects. However, not all this effect can be directly attributed to the current environment. Historically the mining industry has not performed well in its ability to deliver projects according to the financial and physical parameters forecast in the feasibility study process. To manage the risks associated with delivery of major projects, resource companies need to ensure they use a standardised approach to management of their project development to satisfy project objectives and enable more efficient use of the increasingly limited available resources. Each discrete step in advancing the project from scoping study to operations needs to be integrated, reducing the amount of rework and duplication. This paper is primarily a consolidation of existing ideas on project management systems but also introduces new concepts to solve current issues. It describes the basic components of a typical mining project, the issues that commonly arise, the key attributes, and critical steps required for an effective integrated project management system covering projects from initial scoping studies through to project commissioning and operation. This paper focuses on technical study components of the mine development project with allowance for transitioning to design and construction and operation phases.

Jan 1, 2006

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By D. Harrington, M. W. Von Bernewitz

"Introduction In studying the mine disaster files of the Bureau of Mires for preparation of a bulletin on coal-mine explosions, a table was compiled covering various features of fan installations and the handling of air currents at the time of and after the disasters. As a sidelight on this discussion, there was tabulated the loss of life and number of men injured.Discussion of collected dataOf the 164 disasters tabulated, 148 were explosions, 14 were fires, and 2 involved both fire and explosion. The total loss of life was 4,158 and 412 were injured. There were 145 disasters in bituminous coal mines, 13 in anthratice mines, 2 in lignite mines, 1 in a cannel coal nine, and 3 in metal mines. By States, 35 took place in Pennsylvania; 17 in West Virginia; 16 in Oklahoma and Alabama; 15 in. Kansas and Illinois; 12 in Indiana; 7 in Colorado; 6 in Kentucky; 3 each in Ohio Tennessee and Wyoming; 2 each in Arkansas, Montana, Washington, Virginia, New Mexico and Utah and 1 each in Iowa, Missouri, Maryland, and California."

Sep 1, 1924

By Orlando Ramírez

El presente trabajo describe el sistema integrado de seguridad a través de la norma OSHAS 18001 - 1999 y calidad ISO 9001 – 200m, donde la aplicación de la integración controla las desviaciones de los procesos oportunamente. Es decir, que a través de la procalsedad se reúnen tres elementos: productividad, seguridad y calidad,logrando una ventaja competitiva en el mundo globalizado.

Sep 12, 2005