Search Documents

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

By J. D. McLenegan

The purpose of this investigation was to prepare a market survey of the refractories industry in California and Nevada (referred to in subsequent paragraphs as the region), and to determine the degree of self-sufficiency and the potential capacity for anticipated growth. The report includes estimates of the total annual refractories consumption, the quantity of refractories imported into the region, the tonnage of raw materials required for their manufacture, and the resources of fire clay and high-alumina minerals in the region.

Jan 1, 1956

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By Jacqueline JAlexander

Two of the most important phenomena which govern the continuous casting process and determine the quality of the product are the fluid flow and the heat transfer. Steel flows into the mold through the ports of a bifurcated submerged entry nozzle (SEN), which directs the jet to the mold narrow faces where the superheat contained is dissipated on the solidifying shell. Many important aspects of the fluid flow in the mold are transient and difficult to control. However, the time-averaged flow pattern in the mold is greatly influenced by the nozzle geometry, the submergence depth and the mold dimensions. The aim of this work is to analyze the relationship between the heat transfer and the fluid flow pattern inside the mold using the CFD technique at several operating conditions.

Jan 1, 2009

By J. Butra

The underground research presented in this paper was carried out in the two Polish copper mines: Rudna and Polkowice-Sieroszowice. The aim of the research was to determine stress field parameters. The measurement method and measuring positions are described as well as the measuring technique adapted to the geological and mining conditions of the Rudna mine and the Polkowice-Sieroszowice mine. The identified values and directions of principal stresses and horizontal stresses and their importance for optimization of mining operation and safety improvement are discussed.

Aug 1, 2013

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By P Mulvey

"Currently mine process studies and geochemical waste characterisation are considered as two interdependent studies, necessary for the development of the mine and inclusion in the environmental impact statement (EIS). Geochemical waste characterisation will utilise the simulated tailings produced by the mine process studies team to understand the behaviour of the tailings, but the two teams rarely integrate these to develop a coherent and agreed final design.Thorough mine waste geochemical assessments can develop processes to minimise environmental harm, resulting in substantial savings in the decommissioning, closure and rehabilitation phases, and may also be able to address changes in mineral processing methods that can result in substantial savings in process inputs, or even recovery of metal concentrates.Based on geochemical waste characterisation, the full cost of waste management can be calculated and incorporated into the costing of milling.&nbsp; This allows for a more effective evaluation of the metallurgy.&nbsp; A number of examples are presented in which substantial improvements have been made from the collaboration of both the metallurgical and geochemical teams during planning and the metallurgical team and environmental team during operations.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Optimising metallurgy at the planning stage to minimise environmental impact -&nbsp;a feedback loop from geochemical waste characterisation, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors&apos; earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"&apos; if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By Miller RJ, Eager DT, Lama RD

For safe and efficient mining operations, it is essential that environment and equipment status be monitored. A system that gives quick access to status at any given time, and also permits quick analysis of their history, is required. Such a computer based monitoring system has been installed at West Cliff Colliery.The system is based on 2 super mini computers. Three major sub-systems monitor conditions in the longwall operations, environmental conditions in the intake and return roadways, status of the underground and surface installations, and mining and transport equipment.

Jan 1, 1985

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011