Search Documents

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

COMPRESSED air is held in high esteem by the mining engineer as a medium for the transmission of power. The transmission, however, is accompanied by a high percentage of loss. Of the total work done by the steam cylinder'in compressing the air inthe air cylinder, less than 50% is ultimately utilized by the machines underground. These losses are due to its essential and inherent properties as a gas. One of the sources of loss is that due to transmission through the pipes which distribute the air from the receiver to the various places where it is used. As the capacity and economic design of air-compressing plant are influenced by this source of loss, it may be of interest to give an outline of how estimates may readily be made'in practice of thediameter of pipes, quantity of air discharged, and the drop in pressure occasioned.In hydraulics we have a general formula given M Rankine's "Civil Engineering" :It was suggested, the writer believes, in the first instance by D'Arcy, that this formula could be made to apply to an elastic...

Jan 1, 1918

By Roberto Silva de Andrade

O inchamento é um grande problema durante a redução de pelotas de minério de ferro. Várias mudanças podem ser feitas nas pelotas para minimizá-lo. Conforme o sínter utilizado se torna cada vez mais básico, pelotas mais ácidas são desejadas. A adição de MgO, assim como a modificação da basicidade binárias das pelotas pela adição de CaO são soluções que têm sido apontadas. Dessa forma, este trabalho estudou os efeitos do MgO a da modificação da basicidade binária nas seguintes propriedades de pelotas: compressão a frio, porosidade e índice de inchamento. Foram preparadas pelotas com até 5% de MgO e com basicidades entre 0,67 e 1,5. O aumento do teor de MgO causou aumento de porosidade e queda de resistência. A basicidade diminuiu a porosidade e causou aumento de resistência nas pelotas de basicidade 1,0. Tanto o aumento de basicidade quanto a adição de MgO diminuíram o inchamento.

Oct 30, 2017

By M. Grun, A. C. Marlowe, I. Littleford

SYNOPSIS A Wirth tunnel borer owned by Anglo American Corporation completed a 1150m long tunnel some years ago and was subsequently extensively modified by Technical Development Services. In 1982 this borer provided new and particularly interesting information In the field of hard rock boring. The abrasive quartzltes traversed proved to be a challenge to the cutter manufacturer and the project team. This paper examines the problems faced, the solutions found and the lessons learnt.

Jan 1, 1983

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By R. D. Williams

In spite of the increasingly polarized and politicized view of climate science and climate change in the United States, many of the principles behind the ?theory? of Anthropogenic Global Warming (AGW) or Global Climate Change (GCC) are in fact firmly established both in fundamental physics and detailed observations and are widely accepted elsewhere. The discovery of the earth?s ?greenhouse effect? dates back nearly 200 years to the work of French mathematician and physicist Joseph Fourier in 1824 and 1827. In 1872, John Tyndall an English physicist and mountaineer, described the capacity of various gasses to absorb radiant heat. He identified water vapor and carbon dioxide as the principal ?greenhouse? gasses. The work of Fourier and Tyndall was the foundation for the theory that increasing carbon dioxide (CO2) in the atmosphere might be responsible for an increase in global temperatures developed by the brilliant Swedish chemist Svante August Arrhenius in 1896. This was backed up by the additional work of Gilbert Callendar in the 1930s, and Gilbert Plass, Hans Suess and Roger Revelle in the 1950s. There is little scientific dispute about the physics by which this occurs: carbon dioxide in the atmosphere absorbs long wave radiation that would otherwise escape into space, thus warming the lower atmosphere and respective temperatures worldwide. The Intergovernmental Panel on Climate Change (IPCC), approximately 2500 climate scientists from around the world, has concluded that increases in carbon dioxide resulting principally from the burning of fossil fuels are responsible for most of the continuing increases in global temperatures (IPCC, 2007). NASA?s Goddard Institute for Space Studies (GISS) states; ?The ten warmest years all occur within the 12-year period 1997-2008? (GISS, 2009). 2009 was the second warmest year on record and 2010 was tied with 2005 for the warmest year on record (GISS, 2010, 2011). The science is in fact settled; the earth has not cooled since 1998 as some have claimed. It continues to warm as evidenced by not only surface temperature records but also ocean temperature records as well as changes in physical and biological systems (IPCC, 2007).

Feb 27, 2013

By R. V. Ramani

This report is volume 3 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Methane Generator subsystem of the Master Design Simulator. This subsystem is used to determine methane emission rates into the mine environment. These flow rates are then used by the simulator in planning primary and secondary ventilation systems, planning a methane drainage system, and analyzing complex ventilation networks. Both steady state and unsteady state gas flows are included, and have been modeled as second order nonlinear partial differential equations. Finite difference equations are used to obtain numerical solutions to the models using a central differencing scheme. An application of the model is presented. The appendices include derivation of the gas flow equations used in the model as well as a users manual for the computer program.

Jan 1, 1974

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

By P. Koh

A novel approach incorporating computational fluid dynamics (CFD) and flotation modelling has been used for investigating flotation cell designs. CFD modelling has increasingly been employed to enhance understanding of the cell hydrodynamics in mineral and coal flotation. Opportunities for improving the flotation cell performance can be identify by modelling. The CFD-flotation model from CSIRO incorporates cell hydrodynamics that affect particle-bubble interactions. Information from the model includes velocities, turbulent dissipation rates, gas hold-up, particle-bubble attachment and detachment rates. The attachment and detachment rates have been found to be effective measures of cell performance for cell design.

Jan 1, 2011

By Norman Disley, David B. Counter, Lionel Hebert

Misfires in underground and surface production blasts can be costly. Costs can arise from loss of resource, production interruptions, having to redrill or otherwise refire the blast (a hazardous process at best), due to added secondary blasting or breakage, and/or from increased LHD maintenance costs attributable to poor fragmentation.

Jan 1, 1996

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

By P. L. Russell, M. E. Volin, F. L. C. Price, D. H. Mullen

Tin deposits in Catron County, New Mexico, were explored by the Bureau of Mines under authority of the Strategic Minerals Act of August 1939. The investigation covered both lode and placer deposits and was later extended to deposits in Sierra County. Six of the known deposits were examined by E. D. Gardner, supervising engineer of the Southwest Experiment Station of the Bureau of Mines, and S. G. Lasky, a geologist of the Federal Geological Survey, in June and July 1939. It was recommended that the more promising occurrences be explored by test pitting, trenching, and sampling. Field work, under supervision of M. E. Volin, began in September and continued through December 1939. The area was mapped by Carl Fries, Jr., of the Federal Geological Survey, in 1939 and 1940. The La Cruz Development Co. acquired control of the Squaw Creek placer claims in 1942 and began active sampling and development preliminary to large-scale operations. The result of this work showed a considerably higher tin content than that found by the Bureau of Mines in 1939. Because of this report and reports from other parts of the district that large-scale operations for the production of tin from lode deposits were possible, it was recommended that the Bureau of Mines resample parts of Squaw Creek and conduct a mill test of lode material to determine whether a concentrate could be made that was high enough in tin and low enough in iron to be acceptable in American smelting practice. This work, under the supervision of Paul L. Russell, was begun in November 1942 and completed in January 1943, during which time the Sierra Metals Co. acquired control of a large area in Sawmill Canyon. At the suggestion of the Federal Geological Survey and the War Production Board, which had reason to believe that a great deal of commercial material existed on certain flatlands and gully slopes, the project was extended to include test pitting and sampling of those areas. This work was completed in February 1943.

May 1, 1947

By Oliver C. Fursman

The Bureau of Mines undertook this investigation in order to determine the feasibility of producing commercially acceptable alumina and iron by application of the Pedersen process to high-silica, high-titania, ferruginous bauxites of the Pacific Northwest. Calcium aluminate slags were produced by smelting bauxite with coke and lime in an electric-arc furnace. Over 90 percent of the total alumina can be extracted by sodium carbonate solution from slags of properly controlled ternary-phase composition (CaO-Al203-SiO2) that are cooled slowly enough to permit adequate crystallization of the 2CaO-SiO2 and the calcium aluminate compounds. Most of the iron charged was recovered in the regulus; the slag contained about 2 percent iron (as iron oxide), regardless of smelting time.

Jan 1, 1968

By S. Noh, T. K. Kim, B. O. Lee

Future nuclear reactor systems such as a sodium-cooled fast reactor are being designed under severe conditions in terms of operating temperature and irradiation fluence compared to current commercial reactors. For realization of such systems, it is necessary to develop an advanced structural material having both high strength and irradiation resistance at high temperatures. Oxide dispersion strengthened (ODS) steel is considered as one of the most promising structural material because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. Several advanced ODS steels were designed and fabricated by a mechanical alloying, hot isostatic pressing and hot extrusion processes. This study focuses on the effects of heat treatment parameters during the fabrication process parameters on the microstructures of ODS steels for future nuclear system applications.

Jan 1, 2015

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

It has been fairly firmly established (Fisher, N. H., 1945) that the fineness of the gold in any ore deposit varies with the depth from the surface at which the deposit was formed, and, as a corollary to this, that it is dependent upon the temperature and pressure at the time of deposition. This relationship is such that, under certain conditions, the gold fineness, taken into consideration with other recognised criteria, furnishes a very sensitive and reliable guide to the relative temperature of ore formation, at least within the epithermal and the upper part of the mesothermal range.Definition of Fineness.The fineness of gold is calculated in parts per thousand and refers to the proportion of gold present in the naturally occurring metal in the lode, which is actually a gold-silver alloy, containing usually about 10 parts per thousand of base metal and up to 500 parts perthousand of silver. A clear distinction should be made between fineness and gold-silver ratio. The latter refers to the total gold and silver in the lode as determined by assay and is usually expressed as the ratio Au:Ag. Only in deposits where other silver-bearingminerals are entirely absent, which occurs comparatively rarely, can the gold-silver ratio be used as a measure of gold fineness and, in many cases, the two have no relationship. For instance, in the Edie Creek area in New Guinea, the lodes formed under shallow epithermal conditions all carry gold 500 to 550 fine, although the gold-silver ratio ranges from 1:100 to 1:1, in places in adjacent lodes.Determination of Gold Fineness.The fineness of lode gold can be determined only after it has been separated from all other minerals. Amalgamation recovers gold fairly cleanly - unless native silver is present - and the fineness of amalgam bullion is generally a reliable indication of the correct fineness of the gold. If the use of plates is involved, the bullion may be adulterated, but the effect of any copper, or other metal, that may have been introduced can be cancelled by assuming that the gold and silver shouJrl add up to about 990 fine, or by ignoring the base metal content altogether, which varies little in naturally-occurring gold, and in calculating for comparison purposes all fineness figures to the basis Au + Ag = 1,000.The composition of bullion obtained from cyanidation is generally intermediate between the true gold fineness and the total gold-silver proportion as determined by assay of mine or mill-head samples of Cyanide solution dissolves other silver-bearing minerals and the fineness of the resulting bullion is thereby lowered. Consequently, the fineness of cyanide bullion rarely corresponds to the true gold fineness and is useless for diagnostic purposes, although it is a common fallacy to refer to the fineness of cyanide bullion as the fineness of the gold.

Jan 1, 1950

By J. L. Kohler

This final report on Bureau of Mines Contract J0348005 presents the results of an investigation into the development of a Management Information System (MIS) for underground coal mines. The motivation for the research is the unrealized potential for increasing safety and productivity of the well developed mine monitoring system technology. The intent of this project was to examine the information issues, various design aspects of an integrated monitoring/MIS, and associated application concerns, such as the impact of this technology on safety. The work performed on this contract used mine ventilation as a prototypical example. The report is presented in five chapters and six appendices. In addition to the introduction and conclusions chapters, one chapter deals with ventilation MIS system requirements; another with the formulation of a knowledge-based expert system (KBES) structure to implement the integrated ventilation monitoring/MIS system, and one on the health and safety implications of the system. The appendices present details of the KBES system application with an example using a mine ventilation simulator (PSU/MVS). An important conclusion is that a KBES formulation of an integrated monitoring/ MIS for coal mine management is feasible and desirable.

Jan 1, 1986

By F. Rosenblum, P. Spira

"Techniques were developed to determine the oxygen demand of sulphide ore pulps in the laboratory and in concentrators. The effect of variables which influence oxygen demand was studied, and it is shown that the oxygen demand is a measure of the degree of oxidation of the sulphide surfaces. It is suggested that in investigating the significance of oxygen in flotation, the oxygen demand of the pulp is a more suitable parameter than the dissolved oxygen content.Oxygen demand measurements are being carried out with a view to determining the effect of aeration on mill metallurgy and devising improved methods of predicting aeration requirements of sulphide ores.The importance of pulp oxidation in the flotation of massive sulphide ores has long been recognized. At the Noranda concentrator, chalcopyrite could not be floated satisfactorily without a pre-flotation aeration step because the necessary dissolved oxygen was consumed by the large amount of pyrrhotite in the ore. With aeration, pyrrhotite and pyrite were depressed by surface •oxidization, and the resulting thiosulphate level in solution gave a good indication of the end of useful aeration. 1'he present study was prompted by the need to find an alternative criterion for cases where recycled mill water may contain a relatively high concentration of thiosulphate. Preliminary experiments suggested that the rate of oxygen uptake by the pulp -its oxygen demand -might be a practical measure of the end point of aeration as well as a significant parameter in the flotation of massive sulphide ores.Although it has long been realized that oxygen is an important variable in flotation, analytical difficulties precluded detailed plant investigations. Measurements of' dissolved oxygen in mill pulps were first reported by Ralston(i) in 1929. A titration method was used, and because of the delay occasioned by the preparation of clear solution samples, the values obtained were believed to be low. It was quite evident, however, that pulps in the grinding circuit had a lower oxygen content than in flotation. More recently, Woodcock(2,3) used a polarographic probe to carry out oxygen surveys in six Australian concentrators and he generally observed a similar pattern. A large number of other solution parameters were monitored, such as pH, redox potential, reducing power, and reagent and metal concentrations, with the aim of detecting correlations among the measured variables. A few potentin.lly useful relationships were found ""or specific operations in certain plants."

Jan 1, 1974

By O. C. Blade

The southeastern region of the United States is becoming more important as a petroleum-producing area, and it is receiving increasing attention from oil operators. In 1948 total production of crude oil from six southeastern States - Alabama, Florida, Kentucky, Mississippi, Tennessee, and Virginia - was 55,244,000 barrels, which represents 2.7 percent of the Nation's output during that year. Kentucky and Tennessee have produced crude oil since the early days of the industry, but the remaining four States have had production only few years. Data on annual production of crude petroleum in the six States are given in table 1.

Jan 1, 1950

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962