Search Documents

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By J. C. van Dyk

In a previous study by Van Dyk, et al., (2006) and Van Dyk et al. (2006), a FactSage model was developed to understand the chemistry and interpret mineral matter transformation during a fixed bed counter-current gasification process. It was concluded that the FactSage model developed, compared with HT-XRD experimental results and that the FactSage thermodynamic modeling sup-plies insight into specific mineral reactions and slag formation. The specific value for Sasol in using FactSage, in combination with HT-XRD is that it can be used to analyze equilibrium conditions for reactions occurring between inorganic and organic materials together, as well as to provide insight into mineral transformation and slag formation. The purpose of the present study was to improve the current FactSage modeling approach, by combining specific zones in the gasification process. This can improve and speed-up the interpretation of mineral matter transformations and flow properties of reacted mineral matter in coal and assist in identifying and quantifying slag formation in the gasifier operation at temperatures not reflected by normal AFT analyses. The updated and improved FactSage model compared favorably with the original model as well as with HT-XRD results and thus will be able to supply results in a faster and more convenient manner. In the new FactSage model, supported by HT-XRD experimental findings, it is indicated that feldspar formation (including anorthite) correlated with slag formation at temperatures around 1000°C and no slag formation in the base case coal was observed in the drying and devolitilization zone, as was to be expected. Feldspar is one is the mineral species which has the lowest AFT causing the most slag-liquid formation and forms probably as a product between the SiO2, Al2O3 and Ca-containing species. In the gasification zone it was clear that slag-liquid formed at a temperature of 1000°C, with a decrease in the feldspar content. Mullite formation was also observed in the base case sample in the temperature range 1000°C and 1100°C. The decrease in the amount of SiO2 at 1100°C is related to the formation of mullite, but also that the slag-liquid phase also contains an amount of SiO2 in the molten form.

Jan 1, 2014

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

"Above ground, elevated belt conveyors that span more than 200 m (656 ft) between support points can cross valleys, rivers, forests and buildings with a minimal footprint. The cable bridge conveyor (CBC) is a new type of suspension bridge based belt conveyor system that has long spans between support points. It combines a typical belt conveyor and an improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The CBC’s compatibility with current belt conveyors allows versatility in application.A belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground-based or elevated conveyors (Zhang, 2014). The ground-based conveyor has the lowest structural cost when the conveyor is placed on an existing road. Maintenance access is easy and straightforward. Compared to the groundbased conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has a smaller footprint and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss-type structures, with a typical span of 15 to 25 m (50 to 82 ft) between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of a triangular truss-supported conveyor is around 30 to 40 m (100 to 130 ft), while the weight is about 10 percent less than conventional box truss with a shorter span (Jennings, 2013).Long-span elevated structures based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100 to 400 m (330 to 1,312 ft) and beyond. The wide distance between the support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long-span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2014

By Z. L. Huang

A new porous apatite product was prepared using phosphorite from Yichang China by a tem-plate-directed method in self-made reaction equipment under constant temperature and pressure. The product was characterized by XRD, FT-IR and SEM. The results showed that the product was a kind of micrometer porous sphere three-dimensionally structured by apatite nanoflakes, that the average thickness of nanoflakes was about 50 nm, that the average pore size was about 1.2 µm and that the particle average size was about 20 µm. Great amounts of Ca2+channel, high special surface area and regular spherical shape show the potential promising applications of this special porous apatite product in the fields of catalyst, medication, chemical engineering and environment engineering

Jan 1, 2014

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

Datun Concentrator currently processes complex sulfide ores in Gejiu Municipality, Yunnan Province, China. The ore contains much higher arsenic than other ores. The run of mine ore is fed to the concentrator to recover copper and tin by bulk flotation and gravity concentration, and then the other sulphides, such as pyrite, arsenopyrite, etc. didn?t get utilized and are discarded as tailings due to the high arsenic content. In order to utilize the pyrites in the tailings, a series of tests have been conducted for finding the solution of arsenic removal from high arsenic-bearing pyrite concentrates through simple flotation process. By means of orthogonal experimental design, the optimized levels and main factors have been found out for the roughing stage. Through selection of the effective in-organic depressants for the arsenic-bearing minerals, the arsenic in the pyrite concentrate can be removed to meet the requirement of sulfuric acid plant (As%=0.5%) by the open flotation process, i.e., one-time roughing and two-time cleaning.

Jan 1, 2014

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By Luis Cáceres, Genny Leinenweber

"We have designed a planar perpendicular flow cell for electrochemical measurement of a mineral available as a fine powder. The working electrode consisting of mineral powder supported on a carbon paste surface as a 4 mm diameter disk, was concentrically positioned inside a vertical tubular reactor. The counter electrode was a 316L tube embedded in the body cell. The supportive media was a 1.2:1 mixture of candle wax and graphite powder respectively, which is a good electrical conductor. The concentrate electrode as a film attached on a carbon paste disk was prepared rubbing the surface carbon paste against dried powdered mineral. An Ag/AgCl 1 M KCl cell as a reference electrode was attached to the body cell by using a fast coupling fitting. A stable flow rate was achieved using a frequency inverter to drive the pump motor. The flow through the cell verified to be laminar due to the Reynolds number in the cell flow passage. Cyclic voltammetry from - 1200 a 600 mVSAgE were measured using a carbon paste with and without mineral attached to the surface. The main findings of this work were: a). Electrochemical measurement of mineral powder in contact with flowing samples was easily achieved using ground mineral. This is important where massive samples are not available. b). The voltammetric curve features of ground mineral coincided with reported data. c). The working electrode could be quickly replaced while maintaining very good reproducibility."

Jan 1, 2014

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By Aidan Giblett, Karen McCaffery, Robert Dunne

"A worldwide decline in competency levels of practicing metallurgists over recent decades has become clearly evident and is a common topic of discussion among senior practitioners and professional associations. The associated impacts on the industry are material and include operational inefficiencies, missed optimisation opportunities and suboptimal new plant designs. There are many contributing factors to this condition. Decrease in competency is particularly evident both in regions where imbalance between supply and demand has led to a general reduction in experience levels for comparable roles over time and in emerging regions where a rapid rise in demand for practitioners has occurred in conjunction with rapid economic development and industrialization. The context, depth and breadth of education curricula and levels vary with location such that solutions to the technical competency dilemma may need to be developed specifically for each region with these influences in mind. Delivering, demonstrating and maintaining competencies are a critical requirement of undergraduate training and ongoing professional development. Other factors such as generational and cultural characteristics and expectations, political influences, role requirements and employment reward and recognition systems all play a critical role in determining if core competencies can be effectively developed, applied and subsequently maintained. This paper reviews factors impacting and some common approaches to competency development. The authors’ experiences in the management of professional development efforts within the global industry are reviewed and a blueprint proposed to address industry requirements in this area."

Jan 1, 2014

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By Dee Bradshaw

"Process mineralogy’ is a form of applied mineralogy which focuses on addressing problems associated with the processing of ores. ‘Mineralogy’ is the scientific study of minerals and ‘mineral processing’ is the production of concentrates from ores. ‘Process mineralogy,’ however can be defined as the practical study of minerals associated with the processing of ores, concentrates and smelter products for the development and optimisation of metallurgical flowsheets, including the waste and environmental management considerations. This hybrid discipline consists of teams that include geologists, mineralogists, samplers, mineral processors and often others, working together. The degree of cross-training, communication and trust dictates the potential capacity of the team and where an appropriate work dynamic is fostered, in which relationships flourish as much as does the ethic of technical excellence, it is possible to develop technical capabilities that surpass those of conventional teams. The world’s demand for metals is ever increasing and ore deposits available for extraction and processing are lower grade and more complex, often containing deleterious elements that require tailored treatment. Generally, in the past, the technical challenges only needed to be overcome and assessed economically to make an ore deposit viable; increasingly and in the future, a more sustainable approach including environmental and societal considerations is needed. Process mineralogical assessment is increasingly providing the critical information that stands between failure or collapse and survival or success of some mining operations. In this paper, selected case studies are used to demonstrate the valuable role of the process mineralogy tools being used to provide the platform for innovative technology development. Their common attributes are discussed and distilled, thus providing some insights and potential guidance for addressing some of the likely future challenges of the mining industry."

Jan 1, 2014