Search Documents

By M. Wittke

"In the course of the extension of the railway network in Israel, currently the two 4.6 km long tubes of the Gilon Tunnels on the line from Akko to Carmiel are being constructed. The tunnels run through the limestones of the Bina- and Yirka-formations, which locally are karstified. The maximum overburden amounts to 160 m.The limestones are mostly horizontally bedded and vertically jointed. Occasionally also inclined joints exist. The tunnels cross various fault zones, which mostly strike at an acute angle to the tunnel axis and are steeply inclined. The karstic cavities which were encountered during tunneling have partially been filled by clay. In the vicinity of the fault zones, the rock has often been strongly jointed and weathered respectively. The two single-track tubes have a cross section with vertical walls and an open invert. The tubes are connected by cross cuts with a spacing of approx. 250 m.During the tender phase, WBI has elaborated the tender design for a joint venture of a Chinese and an Israeli construction company. After the joint venture had been awarded the contract, the preliminary and the detailed design have been elaborated by WBI and the construction works have been guided. On the basis of the geological description, rock mechanical models have been elaborated, followed by stability analyses on the basis of the Finite Element method. The tunnels have been excavated according to the shotcrete method. The support in most areas only consisted of a very thin shotcrete lining and radial bolts in the area of the roof. Depending on the degree of jointing and weathering, locally advancing support by means of spiles has been applied.The internal lining of reinforced concrete has been constructed in parallel to the heading of the tubes. Mucking and delivery of materials was carried out through the cross cuts.The breakthrough was achieved in April 2014 and thus within schedule. The predicted distribution of the excavation and support classes along the tunnel has been in good agreement with reality."

Jan 1, 2015

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015

By A. Rodriguez-Prado

"Magnetic fields affect the growth of cultured cells and plants; however, limited information exists about their effects on vegetation performing environmental remediation. Constructed wetland mesocosms treating hexavalent chromium (Cr(VI)) wastewater exposed to low-intensity magnetic fields (60 Hz, 56.5 × 10-6 Tesla) produced 100% more biomass than the unexposed control. Nonetheless, they removed only 43 ± 27% of Cr(VI), compared to 60 ± 21% for the control. A Cr(VI) reduction expression was developed as a function of the magnetic field. The design and operation of constructed wetlands to treat mining wastewater can be corrected for magnetic field effects.RÉSUMÉ Les champs magnétiques affectent la croissance des cellules et des plantes cultivées; toutefois, il existe peu d’information quant à leurs effets sur la végétation utilisée à des fins d’assainissement environnementale. Les mésocosmes des marais artificiels traitant des eaux usées, contenant du chrome hexavalent (Cr(VI)), exposés à des champs magnétiques de faible intensité (60 Hz, 56,5 × 10-6 Tesla) ont produit 100 % plus de biomasse que le contrôle non exposé. Néanmoins, ils n’ont enlevé que 43 ± 27 % du Cr(VI), comparativement à 60 ± 21 % pour le contrôle. Une expression de réduction du Cr(VI) a été développée en tant que fonction du champ magnétique. La conception et l’exploitation de marais artificiels pour traiter les eaux usées des mines peuvent être adaptées pour tenir compte des effets des champs magnétiques."

Jan 1, 2015

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By Charles Zdazinsky

Over-break is undesirable in underground civil construction because it excessively damages rock along the perimeter of the tunnel, which directly influences the cycle times of advancement. A quicker cycle time for each process is required to optimize the operation and therefore minimizing over-break is essential for operational success.

Jan 1, 2015

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By R Castedo, L. M. Lopez, J. A. Sanchidrian

In 2014 the authors presented results from 13 tests made with two blasting seismographs on a vibration exciter. They measured coupling transmissibility as function of frequency (i.e. ratio of the velocity of the sensor mount to the velocity of the ground motion) from 16 to 200 Hz at one or two vibrations levels (5 mm/s or 0.2 in/s, and 20 mm/s or 0.79 in/s) with mounts freely placed, sandbagged, and anchored to a granite slab firmly attached to the plate of a vibration exciter. As the memory capacity of one of the seismographs prevented to cover low frequencies, e.g. 4-16 Hz, a new measuring campaign has been recently made to extend the study down to 2 Hz. In this campaign, two more techniques, in which the sensor mounts were fixed with thermal adhesive or a combination of duct tape and gypsum plaster, have been also investigated from 2 to 200 Hz at 5 and 20 mm/s. Free and sandbagged mounts lead to a weak coupling of the mounts to rock, so that transmissibility depends on the characteristics of the imposed rock motion (peak velocity and frequency). Measurements are accurate only at low frequencies (below 17 Hz for free mounts and 10 Hz for sandbagged) in the tested conditions (velocities up to 20 mm/s). Above these frequencies, ground motion in the measurement can be modified by a factor of 0.16 to 1.22. Anchored, glued and plastered mounts achieve a stiff rock-to-ground coupling, ensuring consistent measurements for the frequencies commonly found in blasting independently of the vibration level and the mount characteristics

Jan 1, 2015

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By J. P. Harrison, G. F. Gambino

"This paper examines unpredictability in the parameters governing hydraulic fracturing (HF) as used in stress amelioration for underground excavations, with the aim of showing how this unpredictability may affect design decisions. Using uncertainty models that are appropriate to particular levels of information and degrees of uncertainty, this paper demonstrates how these can aid in decision-making related to feasibility assessments of HF arrays for stress amelioration.Cave mining operations produce large underground voids and high stress concentrations around critical mine locations. These stress concentrations increase the potential for rock burst events. Although de-stress blasting has a long history for redistributing high stress concentrations, to improve safety and reliability HF is now being trialled as an alternative.Unfortunately the HF process is extremely uncertain, and so predicting fracture propagation geometry is difficult. Although the major parameters governing HF propagation have been previously identified, no indication has been given regarding the contribution that uncertainty in these makes to unpredictability in the overall HF system. Using simplified models of HF and referencing a recently proposed characterization of unpredictability, we relate unpredictability in the various governing parameters to the effect it has on strain energy density (SED) in the surrounding rock. Within these models we analyse SED as well as the stress intensity factor (KIc) when investigating the effect of parameter uncertainty and its influence on various crack propagation criteria (Sih & Macdonald, 1974). These models are applicable to unpredictability associated with the development of new fractures; the case of pre-existing fractures is the subject of on-going work.The paper will assess in greater detail the various governing parameters, and investigate the appropriate use of other uncertainty models. As a result, we will show how assessment of uncertainty in HF parameters can be used to both guide feasibility studies and determine the optimal allocation of resources to improve the final design."

Jan 1, 2015

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, C. Jimenez-Velasco

"Most of the gold produced worldwide is still obtained by cyanidation, in spite of the difficulties encountered in the processing of some gold ores such as the dissolution of copper-bearing minerals in cyanide solutions. The leached copper forms complexes with cyanide and causes several operating problems, which have led to the development of copper removal/recovery processes, among them the industrially accepted SART process (sulfidization, acidification, recycling and thickening). Although the SART process is in use in gold production plants around the world, new challenges are appearing with the continuous varying of the mineralogy of ores (such as higher copper grades, changing the solution composition and complexity). The optimal SART operating conditions for a specific solution are not the same when the composition of the solution changes; consequently, the efficiency of this process can decrease.The present study is a thermodynamic approach, corroborated by laboratory experiments, to explain how the main variables of the process affect the efficiency of copper precipitation as cuprous sulfide (Cu2S). The variables considered were pH value, copper concentration, cyanide/copper molar ratio and sulfur/copper molar ratio, all of which werevaried within the limits encountered in typical cyanidation solutions presenting the problem of copper.It was found that the variable that most affects the efficiency of the process was the pH value, since poor or no control of it can cause cuprous sulfide redissolution. The S/Cu molar ratio is also important: raising this ratio increases copper removal, but high ratios will also cause sulfide and cyanide losses. The effect of changing the CN/Cu molar ratio was negligible between 4 and 8. For a solution containing 300 mg/L copper and 490 mg/L cyanide, copper removal as high as 98.8% can be obtained with the addition of 0.6 moles of sulfide per mole of copper at pH = 6.IntroductionThe main process for gold production is cyanidation, because it is the most economical and efficient process so far. Precious-metal leaching occurs when the ore is placed in contact with a dilute alkaline cyanide solution. The dissociation of cyanide salts provides free cyanide ions, which allow the formation of the aurocyanide complex Au(CN)2 -. This complex can be retrieved from the solution by adsorption on activated carbon or by zinc precipitation. Although the use of cyanide represents an issue to health and the environment, there are technologies for its management and treatment that can be easily applied. Furthermore, it is a low-cost process compared with other methods that are available or under development."

Jan 1, 2015

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

By V. Labiouse, F. Orellana

"Hollow cylinder samples can be tested for both the characterization of rock properties and the physical modelling at reduced scale of engineering applications. Particularly, this type of experimental setup can be used to simulate different stress conditions around underground openings, as already developed in the petroleum engineering field e.g. to study the instabilities around deep wellbores during either drilling or the oil production phase. Some authors have also used this technique to successfully characterize the damaged zone around underground openings in the tunneling engineering field looking for an efficient design of their support.This article presents a new hollow cylinder testing device developed at the Rock Mechanics Laboratory of the Ecole Polytechnique Fédérale de Lausanne (EPFL), Switzerland. It allows a full and independent control of the confining pressure and pore water pressure conditions at both the inner and outer boundaries of Thick-Walled Hollow Cylindrical samples. In order to mimicking a tunnel excavation in a porous rock mass, after initial recovery of the in-situ stress and pore water pressure, the hollow cylinders are subjected to a decrease in the internal confining pressure. Moreover, X-Ray Computed Tomography scans of the specimens are performed through the testing cell before and after the mechanical unloading to monitor the displacements undergone and the sample damage. The equipment, testing procedure and data analysis techniques are briefly presented in the paper.The good performance of the apparatus has already been checked on weak rock specimens, among others on Boom and Opalinus Clay samples. In many configurations, the mechanical unloading is found to induce a Damaged Zone (DZ) around the central hole. Its geometry and extent show a great similarity with in-situ observations around tunnels driven in the Boom and Opalinus Clay formations. Such similarities contribute to increase confidence in the understanding and modelling of the ongoing processes."

Jan 1, 2015

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

"The 34th International Conference on Ground Control in Mining (ICGCM) was held July 28–30 at the Lakeview Golf Resort and Spa in Morgantown, WV. Ground control experts have gathered at this location since 1981 to share ideas and successes for improving designs and technologies to enhance the stability of surface and underground mining operations. Ground control is important to all mining operations but is particularly crucial to underground mining to ensure miner safety and operational viability.The year’s event had 240 registered attendees with 20 pecent of that attendance being from the mining industry. A remarkable number of industry representatives attended given the challenges currently faced by the mining industry. A true testament to the value of the conference, the performance of Tom Barczak and Steve Tadolini as co-chairs and the drawing power of the many exceptional speakers that have attended the annual event for many years.The conference operates under the direction of a board of directors with the cooperation, wisdom and assistance of a large organizing committee. Visit the conference website, www.icgcm.conferenceacademy.com, to view the membership of the board and the committee and to access previously published papers."

Jan 1, 2015