Search Documents

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By The DY125-33(Leg 2) Science Parties, Chuanshun Li, Xuefa Shi, Bing Li

"The slow-spreading Mid-Atlantic Ridge (MAR), with a length of ~1.26*104km (Bird, 2003), is the longest mid-ocean ridge on this plant. Separated by the large, left-stepping Equatorial fracture zones, it then be divided into two approximately equal-length parts: Northern Mid-Atlantic Ridge (NMAR, ~6292km) with an average spreading rate of 24mm/yr, and Southern Mid-Atlantic Ridge (SMAR, ~6332km) of 33mm/yr (calculated from PB2002 model, Bird, 2003). Previous works (e.g. Fouquet 1997, Hannington et al., 2011) suggest that slow-spreading ridge could support hydrothermal activities and further favorable for the development of extensive seafloor massive sulfide deposits (SMS). Unlike the NMAR for which large part has been explored for SMS (Hannington et al., 2011; Beaulieu et al., 2015), the SMAR is amongst the least hydrothermal explored spreading ridges until now (Haase et al., 2005, Beaulieu et al., 2015), though both of them show significant similarities in terms of spreading rate, ridge morphology, segmentation, etc. (Macdonald et al., 2001, Sandwell et al., 2014, Tucholke et al., 2008).Before this work, several hydrothermal cruises had been to SMAR since British and German programs starting in 2002, some hydrothermal fields, along with systematic geophysical data, were newly investigated, and types of geologic setting that can host hydrothermal activity were firstly identified (e.g. German et al., 2008; Haase et al.,2005; Haase et al.,2009; Devey et al.,2010; Schmidt et al.,2011).."

Jan 1, 2017

By Lisa Koch, Eleanor Martin

"Each underwater mining project is different. However, most have one thing in common: To be successful. We will draw on our experience advising hundreds of international clients each year on mining, offshore oil & gas and shipping matters to highlight some legal, commercial and practical issues to consider when structuring underwater mining projects. We will look at new ways of allocating risks and rewards in order to obtain much needed investment for underwater mining projects to commence both the exploration and exploitation phase.HighlightsRisk profileWe will look at a typical underwater mining project from the viewpoint of an investor and highlight some of the perceived risks, and potential mitigants.Contractual structureWe will analyse how the mining industry and oil & gas service industry have responded to low commodity prices to examine innovate contractual arrangements with suppliers and stakeholders, and how they can be tailored to the underwater mining industry. FinancingWe will explore some potential financing structures which could be relevant to the underwater mining industry."

Jan 1, 2017

By Richard Harrison, Frank Lim

"Lifting of slurry from the seabed mining machine to the surface production vessel is a critical element of any deepwater seabed mining system. A Vertical Transport System (VTS) comprises pump(s), riser string, connectors and hang-off assembly as its main components, but it is the pipe material, riser configuration and installation method that often attract the most discussions.This presentation will feature important VTS design work 2H has done over the years for different stakeholders, and highlight the work carried out as a partner to the EU funded Blue Mining Joint Industry Project.The key challenges faced by a deepwater VTS are:??High riser payload??Large deck space for storing riser joints??Long time to deploy and retrieve riser??Uncertain metocean conditions??Vortex induced vibrations??Weld and connector fatigueIncreasing the water depth further sees the longer and increasingly ‘springy’ riser experiencing axial resonance caused by wave induced vessel heave motions being close to the riser resonant period. This can lead to snatch loading and fatigue failure in the riser.The presentation will discuss the above design issues, analysis requirements and provide guidance on pump/riser selection. Solutions to mitigate the resonant response issues will also be proposed.."

Jan 1, 2017

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017

By Qinghua Song, Jianhong Chen, Shan Yang, Zhiyong Zhou

"The development process of Metal Resources Technical and Economic Evaluation Expert System (MRTEEES) is introduced in the aspects of requirements analysis, design of the expert system, main functions of the expert system and features of the expert system. The system is based on C/B/S mixed mode and uses ASP.NET technology with .Net Framework being chosen as the development platform and metal resources database providing data support at the bottom layer. The system is an auxiliary management system for metal resources technical and economic evaluation and has the basic functions of auxiliary decision analysis, metal resources database management, data management and comprehensive query. Technical and economic evaluation model can be set up by users independently according to at which stage a project is, mainly including exploration stage, development stage and production stage, and according to the mining methods, for example underground mining, surface mining and in-situ leaching mining. Then, the technical and economic evaluation parameters can be generated. By inputting the value of each parameter in a simple and convenient way, the evaluation results can be directly calculated out and shown in the form of diagrams among others, and feasibility evaluation report can also be automatically generated, making the technical and economic evaluation process accurate and efficient. As the system can achieve the functions of scenario analysis, sensitivity analysis, shareholder’s returns analysis, horizontal comparison of different projects, it can improve the ability of project senior decision makers for rapid response to the rival and meet the demand of pricing negotiations. IntroductionWith the arrival of a new round of industrialization upsurge in both developing and developed countries, growth of demand for metal resources is entering a new stage. Population involved in the new industrialized countries is about four times that of all previous industrialized countries, implying resource consumption increases dramatically both in speed and in quantity. It is a must to seize the strategic opportunity of developing and utilizing metal resources around the world to lay abundant resource base for national industrialization. Objectively speaking, global configuration of metal resources is an inevitable tend. Presently, many issues, for example, resources exploration, mining, merge of mining companies, metal trades, mining financing, etc., generally show the feature of globalization. For the reality that competition for metal resources is becoming fiercer, industry standards of mineral resources will undoubtedly be improved. Occupying large scale mineral resources with high grade and developing them with low cost is the base for the survival of mining companies and metal resources merchants. With the growing demand of global investment in mineral resources exploration, which is at the upstream of the industry chain, geological exploration industry is promising. Globally building market relationships for mineral resources exploration companies is key to their sustainable development. Developing large and super-large deposit with low cost is also an important approach to enhancing core competence of a country or an enterprise. Mining companies around the world are rushing to purchase mineral resources globally. However, in different countries, economic, financial and tax systems for mineral resources vary greatly, and mining and processing techniques, technical parameters and equipment selection also change a lot. Thus, pro-phase research work is necessary for feasibility evaluation of mineral resources projects and it can be time wasting if taken in the traditional way. It is necessary to accelerate the process considering the complex and rapidly changing international situation."

Jan 1, 2017

By Eduardo Lozano, Vilem Petr

The use of explosives brings countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition, and avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation.

Jan 1, 2017

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By Jamal Rostami, Asok Ray, Samer S. Saab Jr., Wenpeng Liu

Ground instability, such as roof or rib failures, is one of the most serious and frequent safety hazards that occur in underground mining, tunneling, and underground construction. The ground-related parameters and features of interest, in assessing roof or rib failures, are location, frequency, and orientation of the joints, voids, as well as rock-strength. These parameters are the main components of rock mass characterization that offers effective strategies for ground support, which, in turn, allow one to mitigate the risks related to ground instability. The main objective of this study is to determine the location of joints and classify rock-strengths by analyzing the drilling data recorded from an instrumented roof bolter while drilling for rock bolt installation during the operational cycle. For this purpose, computer programs based on updated pattern recognition algorithms were developed for joint-detection and classification of rock types to offer an estimated strength. This paper briefly introduces ongoing research on joint detection, especially for joints with an aperture less than 0.125in (3.175mm), by employing an instrumented roof bolter in controlled environments. To improve the capability and precision of joint detection programs in detecting the joints from the drilling data and reducing the number of false alarms, many laboratory tests with various simulated joints and rock-strengths were carried out at a J.H. Fletcher & Co. facility. This paper reviews testing procedures, data analysis, updated algorithms used for joint detection, and discusses the latest round of testing in samples with simulated joints at various angles along the borehole.

Jan 1, 2017

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By Matthew Clay, Colin Chambers, Susan Hookham

Opencast (quarries) and underground mines around the world use blasting methods to mine valuable ore. Traditional blasting systems use technologies such as electric delay detonator systems (developed in the 1950s) and non-electric detonator systems (developed in the 1970s) to initiate a detonation train to blast rock more effectively, and so retrieve valuable product more efficiently. However, the lack of precise control over blast timings with these approaches can result in undesirable outcomes such as significant flyrock, excessive ground vibration, uneven grade of rock and misfires (in which sections of the blast can remain unfired). The development of Electronic Initiation Systems (EIS), first used in the 1990s, introduced a higher level of control over the blast. These systems greatly reduce the negative issues associated with blasting. However, this precision introduces complexity, and with this complexity comes difficulty in demonstrating the predictability, safety and reliability of such systems.

Jan 1, 2017

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly

"A numerical model has been developed to study macrosegregation associated with liquid feeding in the Low Pressure Die Casting of A356 aluminum alloy wheels. The model of the wheel casting process has been implemented within the commercial CFD software package, FLUENT, using a User Defined Function (subroutine) to account for Si rejection based on the Scheil approximation. The model has been validated against temperature and microstructural data taken from a commercially cast wheel. The amount of segregation in the wheel has been shown to be significant in a couple of key areas. The implications of accounting for segregation include an improved ability to predict shrinkage porosity, fatigue performance and potentially also hydrogen porosity.INTRODUCTION The aluminum alloy A356 is widely used in the automotive and aerospace industries for various components. Examples include automotive wheels, automotive suspension components and airframe castings. Focusing on automotive wheels, Low-Pressure Die Cast (LPDC) A356 wheels offer significant design freedom and are far more aesthetically appealing to consumers than conventional stamped steel wheels. A356 wheels now dominate the market, appearing in all but the entry level offerings of the OEM manufacturers. However, they are typically over-designed to allow for the various casting related defects that degrade their mechanical performance. Thus, their potential to save weight has not been fully realized. Wheel manufacturers are under constant pressure to ensure their products meet strict mechanical requirements (ductility, fatigue, vibration), tight geometric tolerances and high aesthetic quality. The mechanical properties of the final product are determined by the microstructure – e.g. SDAS – and the defect population (porosity and oxides). Depending on their size and location, both porosity and oxides, can act as crack initiation sites reducing fatigue life (Caton, 2001; Jordan, 2010; Wu, 2015). There are a number of examples appearing in the literature (Atwood, 2000; Carlson, 2007; Lee, 2001; Yao, 2011) of numerical models that have focused on hydrogen-based pore formation that have demonstrated an ability to predict porosity formation and pore size distributions in geometrically simple castings. These models assume that the local gas species diffusion through the liquid metal to the pores is the rate-controlling factor of pore growth. Another common source of porosity is liquid encapsulation (Dantzig, 2009). As the pressure within the isolated liquid drops, pores form first due to the pressure dropping below the equilibrium partial pressure of hydrogen in solution and then second grow substantially as the pressure continues to drop falling below the vapour pressure of Al. One factor that can affect both mechanisms of pore formation is species macrosegregation, which has received comparatively little attention in die-casting."

Jan 1, 2017