Search Documents

[ENGLISH active earth pressure adapter additive adhesion admixture, addition adsorbed water aggregate air air entrainment air hose allowable bearing value allowable pile bearing load]

Jan 1, 1994

By A. P. Grobbelaar

Andalusite is a member of the sillimanite group of minerals consisting of andalusite, kyanite, and sillimanite. These minerals are the structural polymorphs of Al,Si05 (the anhydrous silicate of aluminium) and although chemically similar, they differ in physical properties due to their different crystal structures. For further information on the sillimanite group, see the chapter on Kyanite and Related Minerals that follows. The minerals are generally the products of the metamorphism of alumina-rich sediments and are found in schists, gneisses, or hornfelses, which have undergone either regional or thermal metamorphism from their original form. Sedimentary deposits may also form since the minerals are chemically and physically resistant to breakdown. When heated to a sufficiently high temperature the sillimanite group minerals convert to mullite with a resultant volume expansion and the liberation of silica. Due to the stability of the mullite formed, its high hot strength and resistance to chemical and physical erosion, they are widely used in the manufacture of refractories and special ceramics (Table 1). The reaction can be represented as follows: [ ] The worldwide use of these minerals depends to a large degree on their availability (Fig. 1). Andalusite, with its lower conversion temperature and the lowest volume expansion on being heated is the natural choice as a raw material to produce energy-saving refractories without prior calcination. The Republic of South Africa holds by far the largest minable andalusite deposits of the world, estimated at some 70 Mt of known in situ reserves. The only other large commercial production of andalusite comes from France, with known reserves of about 5 Mt. Potential new deposits are known from China, Ireland, Australia, and South America. World consumption of andalusite in special performance refractories has risen from less than 10 ktpy in 1960 to nearly 300 ktpy in 1990, which is due to cost effectiveness in many industrial applications compared to other conventional refractory products. Andalusite-based refractories have traditionally been used in Europe, South Africa, and the Far East; usage in America was limited in the past due to relatively high delivery costs and availability of other local refractory minerals. However, there is a significant trend towards greater use of andalusite in North America, thus opening new markets and replacing other traditional refractory raw materials. GEOLOGY Andalusite occurs in metamorphosed rocks of clay-like com- position, as in the andalusite-hornfelses in thermal aureoles (contact metamorphism), formed under conditions of high temperatures and low stress, and in regional metamorphic rocks, such as the andalusite-schists. These schists are mostly unconnected with definite igneous intrusions but were presumably also formed at high temperatures and under low stress. Andalusite can also appear in alluvial deposits associated with the primary deposits. At depths of 10 to 20 km, temperatures of up to 450°C might be expected. Another result of increasing depth is an increase of pressure due to the load of the rock cover. The load stresses involved in metamorphism is generally believed to lie in the range 0 to 10 000 bars. During contact metamorphism the increase in temperature is brought about by the injection of magma. The temperature reached in the country rock at some distance from the igneous body will always be less than the initial temperature of the intrusion, which is presumably less than 1 200°C, and will vary with time and distance from the contact. A simple metamorphic reaction involving dehydration of an aluminous sediment can be: [ ] At higher temperatures sillimanite would form at the expense of andalusite, while kyanite would be the mineral formed at higher pressures, as can be seen in the phase diagram of A12Si05 (Fig. 2).

Jan 1, 1994

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By Marion Loomis

Environmental regulation is an ever growing cost to the mining industry. Requirements for such items as air quality modeling, hazardous waste disposal, selenium concentration in water and sagebrush planting consume more of the mining industry’s resources each year. The mining industry is willing to make the necessary financial commitments to assure that the air, land and water resources are adequately protected and restored. However, it is sometimes difficult to explain to management and stockholders why money should be spent on a specific issue when science and common sense indicate it is being wasted. Common sense and sound science should dictate how mining is regulated.

Jan 1, 1994

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

Provide room-and-pillar operators with practical in- formation and guidelines concerning multiple-seam mine design to reduce ground problems associated with the interaction of adjacent working.

Jan 1, 1994

By Larry Ng, Keith McDonald

The benefits of controlled blasting techniques have gained increasing recognition by the mining industry in recent years. The utilization of an effective controlled blasting programme can result in a safe work environment with less loose rock and a reduced level of scaling and ground support.

Jan 1, 1994

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

By L. D. Robbins, M. L. Murphy, A. C. Campbell, L. Murphy

This paper reports on what appears to be the first discovery of prehistoric mica-schist mining in southern 4frica. The mine concerned was found in a location very rich in rock art that is one of the most important archaeological sites in the Kalahari. The authors conclude that the oval pieces of mica schist that were found at the mine site were used by Khoisan peoples to scrape fatty tissue from hides that were to be cured. Radiocarbon datings seem to indicate that such ovals were used for at least 20 000 years.

Jan 1, 1994

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

By Luis W. Pommier

The developed processes, the subject of this paper, extract the hydrocarbons, halogenated organic compounds and metal contaminants from hazardous soils, rendering them non-hazardous and ready to be placed back on the ground. The processes first segregate a non-contaminated fraction from the contaminated soil. This initial task is performed using available minerals processing technology: sizing, gravity separation, magnetic separation, froth flotation, etc. The remaining contaminated fraction, is submitted to two leaching operations for the removal of organic and metal contaminants, whenever both are present or to a single leaching operation if only one type of contaminant is present. The decontaminated soil fraction is mixed with the non-contaminated fraction and is placed back on the ground. The leaching liquors, used at neutral pH, are non- hazardous. After decontamination the liquids are processed to extract the contaminants, now valuable materials, for commercialization. Organic contaminants are removed by distillation of the solvents. The metal contaminants are precipitated in their oxide form. In both cases the regenerated solvents are recycled. The decontamination processes are economically competitive with transportation and disposal of the soils to permitted facilities for hazardous materials, and most importantly the developed processes remove the liabilities from the Responsible Parties. The law establishes that these liabilities do not disappear with either fixation nor with transportation and disposal since the environmental liabilities are of the ? cradle to grave? type.

Jan 1, 1994

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By P. Ret, E. Üstiindag, R. Dieckmann, R. Subramanian, S. L. Sass

"Partial reduction reactions in the Ni-AI-O system, starting with the spinel compound NiAI20 4, are used to form metal-ceramic microstructures. By suitable choice of processing parameters, such as reduction temperature, oxygen partial pressure and time, two different morphologies of nearly pure Ni particles, equiaxed and rod-like, form within a ceramic matrix, which is either a-A12O3 or a metastable ""defect spinel"". Electron microscopy studies were performed for microstructural characterization, phase identification and chemical analysis. The fracture toughness of the Ni-AI2O 3 mixture was significantly improved with respect to that of the original spinel phase. The important issues that must be addressed to form useful metal-ceramic microstructures by partial reduction reactions rue discussed. It is shown that cracking at the original spinel grain boundaries, likely due to the large volume changes associated with the reduction reaction, can be avoided by the addition of small amounts of ZrO2• Initial results illustrating effect of ZrO2 on the microsuuctures are presented.IntroductionEngineering materials used in load bearing circumstances, particularly under extreme conditions (e.g. high temperatures or stresses), generally are formulated with complex microsuuctures. Such composite-like materials can possess properties unobtainable by either of the individual constituents. With metal-ceramic composites, for example, a material can be obtained with an optimum combination of the low density and high strength of the ceramic, and the toughness of the metal. For high temperature service, where demanding conditions are often present, for example, inside jet turbine engines, a successful new material must have low density, high Young's modulus as well as good oxidation resistance, strength, fracture toughness, creep and fatigue resistance. The candidates include intermetallic compounds, and metal-ceramic, intermetallic-ceramic and ceramic-ceramic composites."

Jan 1, 1994

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By T. P. Meloy

A methodology is presented for the spreadsheet solution of processing networks performing separations with the methodology developed here a spreadsheet grid is used to represent networks with and without recycle loops. In this manner, network solutions are numerically approximated by spreadsheet grid solutions. The methodology was used to explore the ramification networks developed by the Chinese for tungsten and molybdenum processing. Non-linear stage transfer functions for two-component sharp separations can be used.

Jan 1, 1994

By Shad M. Sargand, Glenn A. Hazen, A M. M Jayasuriya

Various types of waves originate from a blast source to propagate through rock/soil media away from the blast. Input vibration to a structure depends on the soil-structure interaction which varies with the dynamic properties at the intersection as well as the stress and strain levels developed from the vibration of the structure-ground system. Hence it is important to study such effects on the response of a structure due to blast loads and this knowledge can be used in the design and control of blasts that are carried out close to buildings, highways and other structures.

Jan 1, 1994

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994