Search Documents

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By P Geddes, K Grohs, C K. McKenzie, M Morrish

Low grade surface gold mining at the Acacia Resources, Union Reefs Gold Mine in Australia's Northern Territory, involves the excavation of benches in three slices after blasting. Blast patterns span zones of high and low grade ore, as well as zones of waste, and selective excavation is required in order to maintain economical head grades for the carbon-in-leach processing plant.

Jan 1, 1998

By Isrun Bohlinger

Resources recovery of brasses for semifinished products often results in the formation of hard spots impairing the quality of following abrasive and/or surface finishing processes. A short survey is given on the recycling processes, followed by the actual knowlegde of genesis, composition, and possibilities of avoidance of hard spots. Informations on genesis and composition of hard spots are completed by data from recent experiments.

Jan 1, 1998

Large variations of coal seam thickness and roof conditions are associated with the occurrence of mine floor undulation at Shoal Creek Mine, operated by Drummond Company, Inc.. Ground control problems, such as roof falls and face failures along with extremely high shield pressure and rapid face convergence, are often reported at the longwall face when these undulations exist. This greatly increases equipment downtime and causes production delays. As a result. a comprehensive study of mine geology including roof conditions and longwall performance were conducted in the mine. With the help of continuous full-face shield pressure monitoring using the Longwall Strata Control and Maintenance System (LoSCoMS), a large data base of shield pressure with various roof conditions has been established. This enables the mine operators to accurately evaluate the roof behavior and shield performance and to take the appropriate operational steps at the face to reduce the number of downtime and face failures. This paper summarizes all works and findings from the study including detailed roof geology and its effect on longwall performance.

Jan 1, 1998

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998

Within CRLÆs lifetime there have been a number of products that have proceeded through their life cycles. In each case market forces and technological advances have forced the cessation of the product. The company has then had to develop alternative outlets for its copper. Sometimes it has produced a similar product to fill the same market. In other cases the extra copper is sold as cathode. Today, CRL produces no semi-fabricated copper products and all cathode is sold. More recently, CRL has ventured into the sale of technology and manufacture of cathode motherplates. This area, whilst it is not what had been a traditional area of core business, has been found to be profitable.

Jan 1, 1998

By A. Rawat

The removal of oxyanions of arsenic present in mine process water and drinking water to a regulatory level is a challenging problem. Recently a patented adsorbent lanthanum oxide has been developed which has shown strong specificity for the anions of arsenic. In this paper the kinetic and thermodynamic aspects of arsenic adsorption on to lanthanum oxide are discussed. Adsorption tests were performed at different temperatures using synthetic solutions of arsenic of varying concentrations. From the kinetic data and adsorption isotherms thermodynamic properties such as Gibb's free energy, standard enthalpy of adsorption, standard entropy, isosteric heat of adsorption and activation energy were determined. The results showed that temperature had a positive effect on the rate and degree of adsorption:The activation energy decreased with increase in the initial concentration thus indicating solute-solute interactions in the system. Also, the isosteric heat was found to decrease with increase in the adsorption density implying a heterogeneous adsorbent surface.

Jan 1, 1998

By R Lethlean

The mining industry in its drive to optimise equipment use and minimise cost simply to remain profitable in an uncertain commodity market needs to develop a greater understanding of equipment capabilities and cost. The factors influencing mobile equipment fleet cost and performance commence at the time of mine planning and continue to exert an influence over the life of the mine. These factors must be understood at the early stages of any operationÆs planning process as they continue to impact both positively and negatively on fleet performance and operating cost throughout the life of the mine. The key factors examined in this paper include: grades; rolling resistance; fragmentation and truck loading.

Jan 1, 1998

Rehabilitation, reclamation and restoration are all terms used to describe the repair of land after mining. Here, restoration is used to mean restoring the land's original use, capability or productivity. Effective restoration is dependent on good planning before mining commences and must include a clear definition of post-mining objectives. The physical condition of the land within the mining licence was that of an imperfectly drained soil in permanent pasture, supporting a seasonal supply dairying unit. During the mining process, the soil layers were separated, with the topsoil stockpiled separately. As part of the restoration process, the land was recontoured to encourage surface drainage, with topsoil spread evenly over the recontoured tailings. Low grond pressure machinery was used to minimise soil compaction, with light discing and harrowing used to increase water infiltration. A permanent pasture was sown, with weed species controlled by spraying, both before and after pasture establishment.  Soil testing has been used extensively to ensure there were no nutrient deficiencies that good compromise pasture establishment and performance. Controlled grazing practices were used to ensure that the sown pastures became well established.

Jan 1, 1998

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increasing usage for acid mine drainage mitigation as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1998

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By Yong-Ming Jiang

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSI-I), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the hackfillcd entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backlill provided stability for the root and Moor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right minethrough and should provide beneficial case study information fur other longwall backfilling applications in the future.

Jan 1, 1998

By P. M. Tait, N. A. Warner

"The refining of thermally produced zinc is currently performed using a highly energy intensive and arguably outmoded process, distilling zinc under atmospheric pressure at temperatures of 900°C to 1000°C. In order to produce refined zinc more profitably and with less environmental impact a new process has been proposed. This process is generic to all thermal zinc smelters and aims to match the purity of zinc from current technology (99.99%-99.999%). The objective is to perform all separation processes using only the heat contained in the smelter product stream. Vacuum conditions are extensively used lowering operating temperatures and enhancing separations. As part of this process zinc is distilled under vacuum from high concentration obtaining a refined product with respect to lead content. A mathematical model has been developed from fundamental principles to describe this stage, the distillation of zinc across a temperature difference between two circulating zinc streams in open channels under vacuum. Heat for the distillation is supplied by the liquid phase, necessitating a large recycle to maintain high operating temperatures, and keep zinc concentrations high. In determining this model and the operating conditions required, relationships between temperature, pressure and composition are considered.IntroductionCurrent technology (the Refluxer) used to refine thermally produced zinc is both expensive and highly inefficient. At present 80% of the worlds zinc is produced via the electrolytic process reflecting the poorer performance of the thermal route, the zinc-lead blast furnace and Refluxer. A new process is proposed to overcome the drawbacks of current processes. These drawbacks are both economic and environmental. The Refluxer requires 6.6 GJ of energy to refine one tonne of SHG zinc 1, other disadvantages of the Refluxer stem from high operating temperature, around 900°C, and liquid zinc being highly corrosive towards ferrous metals. The Refluxer is constructed from silicon carbide sections which join together by means of flat machined faces making liquid metal leaks inevitable. The Refluxer columns are very sensitive to thermal cycling, thermal shock and mechanical vibration, which easily lead to structural failure. To avoid thermal stress on the columns the feed rate and feed temperature need to be kept constant which means the feed baths to the columns must be able to accept solid and liquid feed as the Refluxer has to operate when the smelter is shut down."

Jan 1, 1998

By T. V. Durkin

Approximately 1,390 t (44.7 million ounces) of gold have been produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection by promoting mining as an industry while requiring prevention of pollution and reclamation of affected lands to a beneficial use. The mining laws have evolved since their inception in 1971, especially in response to gold mining. The laws have remained flexible to meet changing regulatory needs. Gold production has continued relatively unabated, even in the face of public scrutiny, two mining moratoriums, and isolated environmental problems. The department's system of "one-stop-shopping" for environmental permits streamlines the permit process, fosters quick resolutions to compliance problems, and helps keep enforcement actions out of the courts. Specific case histories at heap leach mines within the Black Hills are presented.

Jan 1, 1998

By Bidwell TJ, Servant S

Paste back-fill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste hackfll is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the hackfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in-situ measurement of paste backfill properties.

Jan 1, 1998

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under development since. 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

The Cannington silver lead zinc deposit is located near Mt Isa in North West Queensland. This world class orebody is owned by BHP World Minerals (BHP) and is estimated to contain 45 million tonnes of ore at an average grade of 11 per cent lead, four per cent zinc and 500 grams/tonne silver. At BHPÆs planned 1.5 Mtpa extraction rate, the mine life will exceed 20 years. Construction of the underground mine, which commenced in August 1993, was carried out by Peabody Resources Ltd (Mining Services Division) (PRL) for BHP Minerals Pty Limited (BHP) under contract packages totalling approximately $100 M using several innovative techniques to deliver safety, quality and time related project goals. Client/Contractor Partnering, resulting in harmonious working relationships, a combined commitment to the achievement of an excellent safety record, and a seamless transition from the construction phase to operation of the mine, has been a feature of the project.

Jan 1, 1998

By U. Cetin

The Nevada Test Site is located approximately 65 miles northwest of Las Vegas, NY. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, volatile and non-volatile organics, and explosive materials. Leaching and transportation of these contaminants are creating severe environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement of the existing impermeable barriers (clays). In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper will present the results of the sorption tests for the target radionuclides.

Jan 1, 1998

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998