Search Documents

By S. Jennings

The Red Dog zinc-lead-silver deposit is located in the DeLong Mountains of the western Brooks Range in northwest Alaska. The region is located 145 km(90 miles) north of the village of Kotzebue (Fig. 1).Red Dog’s current resource base is 143 Mt (157 million st) averaging 16.1% zinc, 4.3% lead and 83g/t (2.4 oz/st) silver. It is contained in four structurally separate deposits— the Hilltop, Main Deposit, Aqqaluk and the newly discovered Paalaaq deposit. Recent exploration for the Aqqaluk and the Paalaaq deposits has contributed to Cominco American’s understanding of the detailed structural geology of the district and its role in the placement of individual ore bodies.

Jan 1, 1999

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999

By Laszlo Kadar, J. D. Lavers

"In the continuous casting of aluminum killed steel, the tundish nozzle often experiences clogging problems. Water model studies have shown that the clogging problem is dependent on the flow pattern in the nozzle entry region. In particular, the flow can separate at the entrance to the nozzle, leading to the development of a recirculation region. Although a nozzle can be designed such that no recirculation develops, even a small misalignment from the vertical positioning of the nozzle may render the design ineffective.To reduce the possibility of nozzle clogging, the recirculation zone must be reduced or eliminated. This may be achieved by moving the fluid downwards or raising the turbulence level in the separation region. In the case of a tundish nozzle, it is proposed that this can be achieved by using electromagnetic forces.To generate the required electromagnetic force, two systems are considered. The first is based on injecting a DC current; the second by using electromagnetic induction. Both methods are described in this paper. Order of magnitude calculations are provided to illustrate that both methods are essentially feasible. The performance of each method in terms of modifying the turbulent flow characteristics in the nozzle entry region is then examined using a numerical model. It is shown that both methods can greatly reduce the recirculation zone. A cylindrical nozzle was chosen for the model studies since it represents a worst case situation.On the basis of the model studies, it can be concluded that whereas both of the proposed methods have the potential to reduce the troublesome recirculation zone, the induction method appears to be simpler in terms of practical implementation."

Jan 1, 1999

By R. Duckett, D. Salisbury, R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance are reviewed.

Jan 1, 1999

By Daniel A. Norrgran

Grinding ball fragments discharging from SAG mills and ball mills causes extreme wear to downstream processing equipment. These ball fragments, recirculating in a milling circuit, will cause excessive wear to sumps, pumps, hydrocyclones, and interconnecting piping. A magnetic separation system to remove grinding ball fragments from the mill discharge has been developed and successfully applied in the milling circuit. This magnetic separation system - termed Trammel Magnet - was first applied at the Escondida copper concentrator in Chile. The Trommel Magnet consists of an arc of permanent magnets mounted at the discharge end' of the tommel screen. The magnetic arc attracts the ball fragments and removes them from the process stream. This retrofitted magnetic separation system removed 126 metric tons of ball fragments from the circulating load of a. single ball mill in the initial 24 hour period. The mill has since stabilized and the magnetic separator is currently removing 7 metric tons per day of ball fragments. The retrofit of the Trommel Magnet has: 1. Extended the pumpp life and the hydrocyclone life approximately 300 percent. 2. Provided a 5 percent increase in the throughput of the mills by removing grinding ball fragments that contribute very little to the grinding process. Variations of the Trommel Magnet have also been developed for removing grinding ball fragments directly from the mill discharge without the use of a trommel screen. In each case, permanent magnets are used to collect the ball fragments from the mill discharge stream prior to reporting to the sump. These other systems have been designed and fabricated for in-plant test work.

Jan 1, 1999

By D Craw

Sulphur-rich minerals such as authigenic pyrite (FeS2) are commonly associated with coal mine workings. Metallic elements such as arsenic (As), copper (Cu) and zinc (Zn) are enriched in the pyrite relative to their concentrations in the surrounding environment. Exposure of pyrite and coal to air and water results in a series of oxidation and hydrolysis reactions that are commonly catalysed by species of Thiobacillus bacteria. These reactions lead to a lowering of the pH in the drainage waters (acid mine drainage, AMD) and subsequent mobilisation of trace metals in environmentally significant concentrations. This study assesses the spatial distribution of As, Zn and Cu concentration in water in relation to pH and Eh (redox potential) downstream from the tailings at the Wangaloa opencast lignite mine in southeast Otago. This mine was abandoned in the late 1980s due to a decrease in the economic viability of mining the lignite. The area is showing the characteristic symptoms of AMD, which is detrimental to the health of several Pinus radiate growing on some of the tailings. The pH of the drainage waters can get as low as 2, and in some instances, lower, but it returns to near neutral (pH 6.5) up to 200 metres down stream from the base of mine waste piles. It is well documented that the atmospheric oxidation of pyrite is catalysed microbially, causing a substantial decrease in the pH of the drainage waters. Acidification is then counteracted predominantly by natural abiotic remediation processes occurring downstream.

Jan 1, 1999

By Kris Inwood

"In 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nova Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the First World War, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today. The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:(1) ""The most rapid growth of the Canadian iron and steel industry has occurred since 1897 ... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable .... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores:' Donald also argues that metallurgical progress had been necessary to render the ores valuable. ""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions:' The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel-making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1999

By Marco Antônio Siqueira Rodrigues

The possibilities for treating rinse waters fiom chromating bath by electrodialysis are discussed together with the possibilities of optimizing the treatment process for waste reduction and reuse of water and chemical products. An industrial effluent with 4600 ppm of Cr(VI), besides other metallic contamination, was used as work solution. This solution has been recirculated on an electrodialysis cell of three compartments, using exchange membranes Selemiom AMT and CMT. A migration of dichromate ions into the anodic compartment was obtained, so that an extraction of circa 99.9 % of Cr(VI) present on the solution was observed, resulting in water with a Cr(V[) concentration of 4 rnd. These results show that electrodialysis can be used to treat these effluents, and this water could be reused as rinse water. The solution of the anodic compartment, consisting at the beginning of the experiment of H2S04, 0.1 N, reached 7200 mg/l of Cr(VI). This concentrate could be reused on the chromating bath itself.

Jan 1, 1999

By Eric Kelley

Having been retained as a legal expert for the fatality at the Canberra, Australia project, it made me aware of how good intended blasters profess to be implosion experts. Owners and contractors can be misled by these representations, seeing a video of Directionalized Structures constructed of reinforced concrete may be impressive to watch, but lack sound evidence of the true mechanics of an actual “implosion”; on steel structures more prevalently. If any well intended blaster comes to a determination that he can implode a structure, it should be not be construed he cannot. It should be well investigated that the specific blaster has verifiable experience. What happened in Australia reflects on all end users of explosives. I have heard a direct quote in our project in Alberta, “We don’t want to have what happened in Canberra”. Such a tragedy could have, and should have been avoided. Simple by using the “Right Tool for the Job”. We should sideline egos and economics. Would any competent blaster compromise his or her reputation, company or insurability? More importantly, have an honest conscience knowing that if the proper explosive is available, use it, don’t shortcut it. If possible expand the schedule. Better, yet, examine all avenues before the project, and last, cancel the project. A human life is our best asset and should not be compromised.

Jan 1, 1999

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920's with in situ operations in the underground mine and small dumps up to the 1950's. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased' to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By A. Cichowicz

The objective of this work is to quantify the effect of the rock mass surrounding a stope or a tunnel on the seismic signal so that the rockburst damage on the excavation can be derived. It has been shown that the transfer function of rock mass surrounding an excavation can be modelled using a damped oscillator. The method of estimating the transfer function is extended in this paper. The parameters of a damped oscillator are estimated using inversion techniques and the transfer function is modelled as a time-varying system. The technique is tested on data acquired at three different sites in two deep gold mines. Employment of a modal model of the transfer function was suitable in two cases. Application of this technique is essential to track the time variation of the natural frequency during ground motion caused by a seismic event.

Jan 1, 1999

The New Southern Railway (NSR) involves the excavation of approximately 10 km of single bore tunnel from Tempe Reserve, Tempe, to Prince Alfred Park (PAP). PAP is located just south of Central Railway Station in SydneyÆs Central Business District (CBD). From Tempe Reserve the alignment takes the tunnel under Sydney Airport including the main north/south runway. Sydney Airport is approximately 8 km south of the CBD. The NSR is being constructed by a private group, the Transfield Bouygues Joint Venture (TBJV). Transfield is a major Australian contractor and the French contractor, Bouygues, is providing the soft ground tunnel construction expertise and is also responsible for the design of the concrete segmental lining. This paper sets out to present in some detail the issues involved in tunnelling under the airport and in particular under the north apron, the main north/south runway and the new elevated roadway. The paper concentrates on these three areas on the airport with an emphasis on the following. The risks involved and measures taken to minimise the risks in tunnelling under the International Terminal north apron (with Jumbo Jets parked immediately above). Secondly, settlement predictions, settlement and runway operation criteria and the actual settlements that have occurred on the main north/south runway. Finally, the criteria that was developed during the construction of the deep bored piers for the elevated roadway at the Domestic Terminal as the TBM passed through this area of construction activity.

Jan 1, 1999

By Nickolas J. Themelis

The role of copper in the economy will not diminish in the 21st century. Following the tenets of industrial ecology, production and use of copper must take into account both human needs and also how to minimize "collateral" effects on the environment. Dispersive uses will be phased out and post-use recovery of copper will increase. This will result into an advantage for smelting processes that can accommodate mixed metal scrap and waste streams. The bath smelting processes of Noranda and Mitsubishi will continue to make progress but the dominance of the Outokumpu flash smelting will not be challenged until the Noranda reactor overcomes the obstacles to the direct production of copper, thus eliminating the need for a converter.

Jan 1, 1999

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By Martin Stone

Industrialized countries, particularly the United States and the United Kingdom, remain at the forefront of international efforts to control the potential disruption from computer malfunctions caused by the date change from1999 to 2000 — widely known as the millennium bug or Y2K. Disruption is least likely in the developed world, including the United States, Canada, western Europe, Japan and Australasia. However, the picture is potentially different in developing countries where many mining companies operate. The less developed the country, the greater the chance of some form of Y2K-linked disruption.

Jan 1, 1999

By Wenbo Lu

A combined method is present in this paper in analysis the dynamic stability of rock slope under the loading of blast induced seismic, in which, by combining the dynamic load calculating method of quasi-static method with the load inputting method of dynamic finite element method, such factors as the decay of seismic wave along its way of propagation, the frequency. amplitude. the phase difference of seismic wave, etc., can all be taken into account in analysis of the dynamic stability of slope.

Jan 1, 1999

By A C. Edwards

The Mesozoides of North-Eastern Asia represent a collage of exotic terranes which were accreted to the margins of the Siberian continent. In the Late Precambrian and Phanerozoic, the passive margin of the Siberian continent (the current north-east) broke up into a number of discrete fragments as a result of rifting events in the Riphean, Early and Middle Paleozoic. Rift related mineralisation includes stratiform and stratabound copper and base metal mineralisation in the structures of the Omulevka, Okhotsk and Prikolyma basement terranes, as well as along the edge of the Siberian continent in the Paleozoic sediments of the Verkhoyansk passive margin. During the Late Mesozoic the terranes were reassembled in a series of accretionary events. At the end of the Jurassic, the velocity of the Kula plate increased, and the opening of the Canadian Basin in the Arctic commenced, changing the vectors along which the Siberian and North American plates moved. Island arcs terranes were pushed back onto the Omolon super-terrane which was in turn pushed onto the Siberian Craton in a series of massive collisional events that resulted in the restructuring of the whole region. Numerous granitoids characterised by collisional and island arc chemistries with Au and accompanying Sn, and W mineralisation were emplaced. Mesothermal gold-quartz mineralisation was emplaced in a series of narrow belts that adjoin major crustal sutures and that spatially overlap belts of granitoids and zones of subgreenschist metamorphism. Each of these gold-quartz vein belts corresponds with a specific collisional phase. In the middle Cretaceous, the Okhotsk-Chukotka volcanic belt developed along the paleo-Pacific margin of the Siberian continent. Epithermal Au-Ag developed in the volcanics and shallow mesothermal Au-Ag-quartz and Au-Sb mineralisation developed in the Mesozoides. Porphyry and skarn style mineralisation developed in both the island arcs and in the continental Okhotsk-Chukotka Volcanic Belt.

Jan 1, 1999

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999