Search Documents

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By P J. Terbrugge

The concept of vertical pit mining has been developed as an alternative mining method for the exploitation from surface of small, vertical or near-vertical, massive orebodies down to depths of some 200 m, where ore extraction from conventional open pit excavations is rendered uneconomic due to high associated waste:ore mining ratio. Systematic lateral support maintains vertical pit sides, thereby minimising waste mining volumes. Stability analysis techniques have been developed for design of this lateral support, with the support quantum, primarily comprising long cable anchors, dependent upon country rock strength characteristics and pit configuration. Where the cost of support is less than the cost of the comparable conventional pit waste excavation, vertical pit mining becomes an economically viable alternative, additionally providing the benefit of reduced environmental impact and rehabilitation requirements for the mining area. The technique has been successfully applied for the mining of a chrome deposit in Zimbabwe to an 80 m depth, believed to be unique in the world, and a full feasibilty study for a 3000 m2 diamond pipe has been carried out for mining to 200 m depth.

Jan 1, 2000

By Yoshinobu Fukumori, Testuya Watanabe, Futoshi Shikata, Hiroyuki Tokumitsu, Hideki Ichikawa, Masahito Miyamoto

Nano-particulate systems have attracted much attention recently in pharmaceutical field as drug carriers and functional components of pharmaceutical dosage forms. This paper describes our approaches in design and preparation of nano-particulate systems, including lipid nano-emulsions, chitosan nanoparticles and thermosensitive acrylic nanoparticles, for certain pharmaceutical applications mentioned below. The lipid nano-emulsions with their particle size smaller than 100 nm were prepared for gadolinium neutron-capture therapy (Gd-NCT) of cancer by a thin-film hydration method with sonication, and intraperitoneally injected into Greene's melanoma (melanotic No. 179)-bearing Syrian hamsters. This provided such a high gadolinium concentraton in tumor as 107 µg/g tumor (wet basis) at 48 h after administration. As an alternative gadolinium nano-carrier for Gd-NCT, biodegradable and highly gadopentetate-loaded chitosan nanoparticles (Gd-nanoCPs, 426 mTI in particle diameter and 9.3% in Gd content) were prepared by a novel emulsion-droplet coalescence technique. A significant tumor-killing effect could be obtained when Gd-nanoCP suspension was injected intratumorally twice 24 and 8 hours before neutron irradiation into B 16Fl O melanoma-bearing mice and subsequently thermalneutron was irradiated toward tumor site with a flux of 2 x 109 n/cm2/sec for 60 min. As one another application of nanoparticles, a novel acrylic composite latex with a hydrophobic core and a thermosenstively swellable shell was designed for fabricating microcapsules showing thermosensitive mode of drug release. The microcapsules with the composite latex-dispersing membranes exhibited an exceptionally rapid on-off response of drug-release in a thermosensitive manner.

Jan 1, 2000

Tracey Khanna, Assistant Editor of UK?s Mining Magazine discusses some of the new and important environmental challenges, physical and social, that are facing mining companies. The tide of public opinion has turned strongly against those companies which are unable to show that they are practising responsible environmental stewardship. This is, no doubt, in part due to the recent focus of the international media on environmental issues and constantly improving means of communications, which has brought the whole subject of mining and the environment to those who, in the past, had only a limited awareness of the industry. Mining companies today face new and important challenges with regard to the environment, both physical and social. New technology and a greater understanding of waste management techniques has helped to bring about improved handling and disposal of mines wastes, so reducing some of the impacts. However, improved technology has also brought about the economic viability of exploiting increasingly lower-grade ore from open pits, resulting in a greater visual impact.

Jan 1, 2000

By Uchil Jayagopal, P. V. Krupakara, S. Manjunath

"This paper deals with the corrosion characterization of quartz particlate ZA-27 alloy metal matrix composites (MMCs). Quartz particles of size 50-80 microns are used as reinforcement. MMC's are prepared according to ASTM standards. Composites containing. 2, 4, and -6% by weight of quartz and unreinforced matrix were tested using 1 -N hydrochloric acid: The composite was found to be more corrosive resistant than matrix alloy. In each test the corrosion resistance of both alloy and composites were found to decrease with the exposure time.1. IntroductionMetal matrix composites- (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight 1-5. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments Particles reinforced MMCs has been the most popular over the last two decades.ZA alloy MMCs have most popular families being represented by. ZA-27 alloy reinforced with ceramic particulate. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior.ZA alloys have been used extensively in industry. This is attributed to their excellent fludity, castability and good mechanical properties. Among the zinc-based foundry alloys, the ZA family of alloy have been widely used during the past few years. ZA alloys have many advantage over aluminium based ones, especially high strength with a low casting temperature 8."

Jan 1, 2000

By Graeme G. Strathdee

"IntroductionThis paper presents an overview of the industry status, describes current potash industry practices at three mills, and summarizes developments that have taken place since the previous review by Banks (1985).The commodity potash is produced in both New Brunswick and Saskatchewan from the evaporite ore sylvinite. This ore is a mixture of co-crystallized halite, NaCl, and sylvite, KCl, and a minor assortment of silica, carbonate, sulphate, and clay minerals. Carnallite, KMgCl3.6H20, is also dispersed throughout the bedded deposits and can affect the recovery of sylvite for fertilizer and industrial uses.Canada continues to be a principal source of supply of agricultural and industrial potash products. Figure 1 shows the sector performance between 1989 and 1997 in the context of the world supply and demand situation as reported by Prud'homme (1997) of Natural Resources Canada.Potash industry output is traditionally measured as the quantity of potassium nutrient and reported as tonnes ofK20. Mineralogically, the principal form of potash produced in Canada is sylvite, KCl, and 1 nutrient tonne K20 corresponds to approximately 1.64 tonnes of sylvite of agricultural grade, about 95% KCI. In 1997, the Canadian industry milling capacity was 13.4 million metric tons (Mt) ofK20 (22 Mt KCl) while the actual production was 9.0 Mt K20 (14.8 Mt KCl). Worldwide milling capacity in 1997 was 35.9 Mt K20 (58.8 Mt KCl) and global consumption was 25.3 Mt K20 (41.6 Mt KCl). Canadian producers can deliver about 35% of the global demand for potash commodities"

Jan 1, 2000

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By R. W. Smith, D. L. Taylor, K. A. Altman

Recent research has shown that traditional sensitivity, what if and best case/worst case analysis of metallurgical data has the potential to over estimate the value of mining projects. Use of simulations, which rely on the input of statistical information, may provide more realistic predictions of the value of future projects. Actual metallurgical data is used to demonstrate that analyzing the data from a statistical perspective can give insight into completing an optimum amount of metallurgical testing and a mechanism to determine that samples used for the testing are truly representative of the ore that will be processed.

Jan 1, 2000

By J. A. Oraniscak

Longwall mining operations continue to increase extraction rates and the potential to generate higher amounts of airborne respirable dust (ARD). The National Institute for Occupational Safety and Health (NIOSH) has gathered data from underground longwall surveys and laboratory crushing tests to identify the important factors influencing the amount of ARD levels generated. Coal-seam characteristics, operational parameters (i.e.,cut sequence, mining height, etc.), extraction rates and dust-control parameters (i.e., airflow, water flow, etc.) were examined to determine their influence on ARD levels measured at longwalls during actual mining operations. ARD generated by a laboratory crusher while crushing bituminous coal samples collected from underground longwalls was also examined to determine if there were cor relations with coal-seam properties. Results from the longwall and laboratory data collected indicated that low-ash, high-volatile coals (low moist fuel ratio or MFR coals) generate higher amounts of ARD. It was found that face ventilation and water application to the coal product are essential elements to controlling longwall ARD levels.

Jan 1, 2000

By A. Burger Pintér

To be meaningful the sharing of ideas about the National Environmental Management Act (NEMA) and social issues within the context of Mining and Metallurgy (M&M) requires an honest scrutiny of the M&M/social environment relationship, both past and present. It is not a secret that this relationship has been and is fraught with difficulties. Thus from all perspectives (M&M, society and environmental and social consultants) such a dissection, that highlights the realities, both good and bad, is uncomfortable. For this section of the colloquium to have any value, the honest but difficult approach needs to be taken.

Jan 1, 2000

By Peter Halbach

The two HYFIFLUX cruises of the German RV SONNE (SO 99/1995 and SO 134/1998) were organized in the framework of a co-operation between several German universities and two European marine research partners. It is a multidisciplinary program for the study of hydrothermalism with its associated geological, mineralogical, and biological processes in the North Fiji Basin (NFB) in the SW-Pacific. The main achievements of the HYFIFLUX cruises were detailed multibeam Hydrosweep mapping in order to identify the detailed tectonic setting, water sampling at hydrothermally active vents, mineral sampling at inactive sites with sulfide, sulfate, and silica mineralizations, and sampling of basaltic rocks, (Halbach et al. 1999). Oceanic accretion in the NFB is characterized by a double spreading system (Auzende et al. 1994),with one spreading axis located in the median part of the basin (Central Fiji Ridge, CFR) and the second one located immediately west of the Fiji platform (West Fiji Ridge). Most of our investigations were done in the northern part of the N 15° segment of the CFR, which corresponds to area A of our program, area D is located farther south in the NFB and corresponds to the N-S segment of the CFR (Fig. 1). During previous works under the French-Japanese STARMER project, the active ?White Lady? mound and the extinct Père Lachaiseí site were sampled; these samples were studied by Bendel et al. 1993. Here an inactive hydrothermal field was studied, where there were many sediment-covered chimneys in various stages of disintegration, (Bendel et al. 1993). However, the area immediately southwest of the nodal circular basin, which is the triple point junction of the medium-spreading Central Fiji Ridge (about 6 cm/yr spreading rate

Jan 1, 2000

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By Tadashi Aiura, Yasuhiro Miura

"A small amount(0.2mass%) of Scandium(Sc) was added to the 7.NOl and 5083 Al alloys as a refiner and stabilizer of microstructure, and the resulting microstructures were discussed in comparison with the effects of the conventional additives. The followings are summarized: 1) in the as-solidified structure, a ·decreased tendency of constitutional supercooling and increased solubility of Mg were recognized for the Sc-added 5083 alloy. Sc is a -better microstructure refiner for the 7N01 alloy than Zr, in a sense that it does not suppress the favorable effect of· coexisting Ti. 2) Sc effectively suppresses recrystallization both in the 5083 and 7N01 alloys. 3) The rod like primary Al3Sc crystals formed during solidification, as well as the fine dispersion of Al3Sc precipitates formed by subsequent heat treatment, can act as a strong recrystallization suppresser. IntroductionThe 7N01 and 5083 alloys are the most popular industrial Al alloys and they are widely' used for various structures because of their superior properties. Fine macro and micro structures of the materials are required for obtaining acceptable sec resistance,consistent appearance of anodized surface and good weldability, as well as good mechanical properties. In order to produce fine grain structures, transition metals, such as Cr, Zr, and Mn, have been conventionally added.It has been reported that Sc is an efficient refiner [l, 2] and can be an alternative for the conventional and also suppresses recrystallization in Al alloys [3,4]. Scandium is the lightest transition element and forms an equilibrium intermetallic phase. The equilibrium phase, Ll2-Al3Sc, is coherent with the matrix, and of _spherical shape. A fine dispersion of the spherical precipitates is obtained by quenching and aging after solutionizing annealing. The authors have already reported a part of the experimental results on the effect of Sc on the as homogenized microstructure of the 5083 alloy [5]. In the present study, the effects of Sc on the macro and micro structures of the industrial high strength Al alloys(7N01 and 5083) for extrusion are investigated, and the superior role of Sc as a grain refiner is shown"

Jan 1, 2000

By A. E. Dabbagh

Saudi Arabia’s mineral potential offers development target that compliment the national effort to diversify the income of this oil and gas economic based nation. Ma’aden, a joint stock company with paid-up capital of US$1 billion, has from its inception in 1997, actively developed in-house engineering and management skills to transform the Arabian shield’s mineral potential into such real projects. Gold mine operating facilities of 100,000 oz/yr underground and 50,000 oz/yr open pit are de-scribed, as well as 3 targets, two of which are underdevelopment; Al Hajar (3,000 tpd at 2.5 gpt Au)and Al Amar (5,000 tpd at 20 gpt Au). Emphasis is also on exploitation of phosphate rock and down-stream fertilizer products, based on the Kingdom’s107,000 sq. km. northern basin geological reserve. Al Jalamid, the prime target, represents 216 million tonnes of these P2O5 reserves. Saudis and expatriates, together, lead international engineering companies and contractors operating and developing these facilities.

Jan 1, 2000

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By C. Restarick, R. G. Robins, R. M. Taylor, I. Ennis

Lime addition to acid mine drainage waters (AMD), possibly accompanied by aeration, has been the basis for their remediation by precipitation of predominantly metal hydroxides. An efficient novel alternative technique causes precipitation of double M(II)-M(III) hydroxy sulfates which readily precipitate and are easily dewatered. When the Fe(II)/Fe(III) + Al(III) ratio of the AMD is appropriate, the Green Precipitate (GP) Process provides a more effective alternative to normal liming/aeration. The process can be adapted to give a continuous in-line treatment by the choice of suitable computer-controlled reactors designed to improve the liming efficiency, reduce scaling and control the rate of treatment. The processes are described in terms of the chemistry involved.

Jan 1, 2000

By K. Iwami, K. Abe

"Onahama Smelter and Refinery has been operated-since 1965 arid currently produces 243,000 metric tons per year of cathode copper. The Onahama tankhouse consists of conventional-type No.1 and 2 tankhouses with the capacity of 123,000 metric tons per year and No.3 tankhouse with 120,000 metric tons per year, adopting jumbo tank system, using hazelett anode respectively.In October, 1996, for the purpose of improving the - anode verticality, new anode copper body press machine has been installed in No.1, 2 tankhouses; by increasing Walker type anode copper weight by 35kg to 365kg. Consequently, it is possible to raise current density from 191 to 222 A/m2 and the No.1 and 2 tankhouses capacity was increased by 15,000 metric tons per year to 138,000 metric tons per year.At present, the refining capacity is 258,000 metric tons per year in total including No.3 tankhouse.This figure is the largest one in Japan.IntroductionSince the Onaham tankhouse was put into operation in 1965, the cathode copper production has increase with much labor cost saving.The following two cases to increase Walker type anode copper weight by 35kg to 365kg were studied.a) To increase the cathode copper production by raising current density.b) To save the labor cost by prolonging the anode cycle in order to decrease the exchanging time of electrodes.So the electrolytic tests were carried out to confirm· the effect of current efficiency, cathode copper quality and working conditions for space adjustment.As a result, we concluded that it was indispensable to introduce the anode body press machine to keep usual current efficiency and cathode copper quality with same workers, and to be possible to increase cathode copper production.In addition, the high-speed press machine was needed to maintain same working time and which specifications were decided through various investigations. In October 1996, the new anode body press machine made by Kawazoe Machine Works, Ltd. has been installed in No.1 tankhouse."

Jan 1, 2000

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000