Search Documents

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By S. A. Osterberg, J. L. Breckenridge, R. S. Popielak

Multidisciplinary investigations were completed to prove the availability of water resources for the proposed San Cristóbal silver-lead-zinc mine in the arid Altiplano of Bolivia. Surface water resources are scarce, of poor quality, and unsuitable for development. Therefore, hydrogeological reconnaissance targeted alluvial aquifers for development. Follow-up resistivity, refraction, and water quality assessments were used to prioritize areas with prolific production potential. Pumping tests and regional water balance analysis indicate an alluvial aquifer can sustain the required approximately 40 000 m3 per day production for the life of the mine and predict no significant negative environmental effects on local groundwater users and the environment.

Jan 1, 2002

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By Steve Kral

The mining industry is no stranger to hard times. Throughout its history, the industry has faced the ups and downs of commodity prices, difficult-to-mine-and-process ore bodies, labor issues and other problems. Throughout it all, though, the mining industry continues to provide the materials needed for society —even in the face of attacks by those who seek to cripple the industry or have it go away. The reason the mining industry survives, of course, is that mankind requires the products the industry produces. And, in recent decades, the industry has developed new technologies and improved on existing ones to produce those products in environmentally sound ways. At the same time, the economic benefits have been enormous to communities throughout the world where mining takes place.

Jan 1, 2002

By M. M. Botz, F. W. DeVries

Discussion by F.W. DeVries Comments on natural cyanide attenuation. The paper by Botz and Mudder in the November 2000 issue of Minerals and Metallurgical Processing had one disappointing aspect. Table 1 (p. 229) failed to include a significant species - neutral copper cyanide (CuCN). This compound has been most trouble-some in many plant-scale cyanide cleanup processes, includ- ing acidification-volatilization- reneutralization (AVR), hy- drogen peroxide cleanup and air/SO2 cleanup. It has also plagued many pilot efforts to use ion-exchange (IX) resin technology. This author elucidated the concept that, under some conditions, copper cyanide failed to precipitate out of treated effluents and appeared to exist as a filterable colloid that reported as copper and cyanide, with the latter measured as WAD (weak-acid-dissociable) cyanide in that analytical method. The concentrations measured were very near the levels of 0.2 ppm, often the regulatory limit for WAD cyanide. The copper concentration, using the 1 : 1 ratio for this com- pound, would then be more than 0.4 ppm, which could also be unacceptable. We discovered that it was unsafe to assume that the Cu(CN),- would surrender both cyanide ions simultaneously and allow cupric copper to be removed subsequently as, say, cupric ferrocyanide (Hatchett's Brown). This compound could be ignored as safely as the "iron blues," as essentially an inert solid, stable in geologic time if not exposed to sunlight. Under poorly controlled oxidation of the cyanocuprite ions (copper with four, three or two cyanides complexed to the copper), CuCN could well be formed and could not be assumed to precipitate out as a solid. The authors of the paper, by failing to include the CuCN species in their model, may have left users of the model prone to ignore the possible occurrence of the colloidal(?) form in the discharge, thus finding an effluent that failed to meet regulatory limits. (See addendum below.) This somewhat ephemeral material may well have been responsible for some large-scale failures of cyanide destruction technology to succeed at sites in North America and elsewhere. Two specific references alluding to this occurrence may be found: Griffiths et al., 1987, "The detoxification of gold-mill tailings with hydrogen peroxide," Journal of the South African Institute of Mining and Metallurgy, September, p. 282. DeVries, 1989, "Improved understanding in detoxification of cyanide leach liquors using peroxide" Rand01 Gold Conference, Sacramento CA, p. 15 1. It is advisable for workers in this area of cyanide removal or recycle to avoid assuming that CuCN will, with certainty, precipitate out of solution, or that the dicyanocuprite ion will part simultaneously with both cyanide ions and allow cupric copper to be dealt with by other reactions. One further piece of work may be incomplete. That is, a definitive study of the long-term behavior of CuCN that does precipitate when exposed to other compounds present in neutralized tailings. Addendum. The extremely complex reaction of cupric ion on cyanide- which, of course, results in oxidation of cyanide to cyanate, probably through the intermediate stage of forming cyanogen [(CN)2] from oxidation of HCN with its hydrolysis to cyanate and cyanide ion - involves two cyanide moieties and the reduction of the cupric ion back again to the cuprous state. This, then, can form the CuCN potential "solid" that was already the undesirable species. In cyanide cleanup, with either air/SO2 or hydrogen peroxide, copper is generally employed as the catalyst, so it is unclear what happens when the CU(CN)2-1 is ultimately exhausted. Certainly, the field evidence is quite clear that all

Jan 1, 2002

By J. Ran

"Hangingwall sloughing is the major cause of unplanned stope dilution in open stope mining. Understanding the hangingwall sloughing mechanism can guide the stope design in minimizing the unplanned dilution and improving muck size and therefore mining efficiency. Though the modified stability graph method may be adopted to assess the hangingwall stability, for mines where the hangingwall is inaccessible, the required parameters are difficult to define and some of the simple influential factors cannot be easily identified in this method to provide guidelines for stope design.This paper identifies the main modes of hangingwall sloughing in open stope mining based on detailed data collected from mined-out stopes and site observations, applies the voussoir beam notation to analysis of the hangingwall sloughing mechanism, compares the model analysis results with the collected stope data, and provides guidelines for stope design and model application. Finally, examples are given to demonstrate the time and support effects on hangingwall sloughing and stope dilution."

Jan 1, 2002

By C. R. Edwards

"The Cigar Lake project will develop the world’s second largest high grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the high grade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2005.INTRODUCTIONThe Athabasca Basin in northern Saskatchewan hosts a number of large uranium mining and milling operations, including Cluff Lake, Key Lake, McArthur River, McClean Lake and Rabbit Lake. (Edwards 1988, Edwards 1992, Fielder 1998, Edwards and Oliver 2000, Edwards 2001) The latest project in the Athabasca Basin is the Cigar Lake project."

Jan 1, 2002

By P. N. Saavedra, E. A. Salamanca

"The maintenance strategies in the mining industry are changing from operative and periodic inspection strategies to a condition-based, predictive maintenance strategy centred in vibration analysis plus complementary techniques. Condition monitoring can also help to improve availability by being able to pinpoint and diagnose problems on operating machinery at an early stage. This reduces unscheduled downtime and production losses.However, in mining, for shovels operating in transient modes, with variable load and/or speed, the FFT (Fast Fourier Transform) standard approach is not directly applicable for analysis. This work illustrates how spectral order analysis and new transforms, called time-frequency transforms (TFT), allow us to monitor the shovel when it is working. Some practical examples showing the application of these analysis techniques to occasional vibrations measured on hoist and crowd transmission of a shovel are also presented. It is shown that at present, it is possible to carry out the vibration monitoring in the mining shovel while it is working, therefore avoiding the high cost of a loss of production which can occurr in traditional monitoring, where the measurement is taken while the shovel is out of production."

Jan 1, 2002

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By G. Lawrence, R. Pieters, A. Leung, T. Pedersen

The Main Zone and Waterline pit lakes at the Equity Silver Mine near Houston, BC (Canada) are the sites of a new 3-yr research program with three primary goals: 1) understanding controls on metal concentrations in the lakes; 2) using mesocosms to test a variety of remediation strategies; and 3) verifying and improving an existing coupled physical-geochemical model with the goal of improving predictions of pit lake water quality. Initial data from two summer surveys in the Main Zone pit lake reveal elevated dissolved metal concentrations (e.g. [Zn] as high as 800 µg/L) present in a two-meter-deep mixed layer, and elevated particulate metal concentrations towards the bottom of the water column. Hydroxide sludge, a byproduct of ARD treatment, is being discharged to the surface waters of the Main Zone pit lake. The sludge sinks rapidly to the lake bottom, leading to deep waters with elevated levels of dissolved O2 and total metals. By contrast, the deep waters of the proximal Waterline pit lake are mildly reducing, manifested by depletion of O2 and elevated levels of dissolved Fe. These reducing conditions have led to elevated levels of As (up to 1500 µg/L) in Waterline pit deep waters. The contrasting behavior of these two pit lakes, as well as the processes controlling metal concentrations in the lakes, will be discussed.

Jan 1, 2002

By Donald E. Garrett

Sodium sulfate is one of the larger tonnage industrial minerals. A little more than half of this tonnage — 3 Mt/a (3.3 million stpy) of natural product— is recovered from ore deposits. Most of the rest is produced as a byproduct from other manufacturing operations. Sodium sulfate is mined in a variety of ways. These include conventional room-and-pillar mining, strip mining, in situ leaching of thick ore beds, solar evaporation and cooling-crystallization of lake brine, and the pumping of brine from complex salt deposits. There is also a variety of commercial sodium sulfate ore sources. They include thenardite (the mineral form of sodium sulfate, or Na2SO4), mirabilite (glauber salt,Na2SO4•10H2O), glauberite (Na2SO4•CaSO4), astra-kanite (bloedite; Na2SO4•MgSO4•4H2O), burkeite(2Na2SO4•Na2CO3), sodium sulfate-containing caliche and various brines.

Jan 1, 2002

The profitability of individual ore blocks can be classed as clearly profitable, clearly not profitable, and those in between which are by nature quite sensitive to their major cost and revenue drivers. It is often the case that the most effort goes into the least profitable ore blocks to ensure that these will in fact not generate a loss. In these cases a cut-off grade policy is often not sufficiently live to separate individual sources given the volatility of financial markets and individual circumstances of some sources particularly in remnant operations such as Mount Isa MinesÆ Lead Mine. Standard sensitivity analysis can determine which factors stope profitability is most sensitive to. However, this does not usually indicate the likelihood of any input change, nor the combined effect of multiple inputs changing. The author attempted to modify the Lead Stream financial model that determines cash margin by inserting probability distribution functions and then using Monte Carlo simulations to determine the probability of any particular ore block making a profit. This effectively demonstrates the combined effect of varying a number of inputs simultaneously to provide a probability of making a profit. The limitations of this analysis lie in the accuracy that individual probability distributions can be specified. Attempts to generate valid functions from first principles have proved difficult for a number of reasons and these are discussed along with some practical alternatives.

Jan 1, 2002

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By Bruce W. Woolpert

During the SME Board of Directors’ midyear meeting in Monterey, CA Aug. 25, I discussed trends in the construction aggregates industry. Many construction-material suppliers may not have yet fully internalized the changes that are taking place. But the changes are significant. And they have shifted the focus in the aggregates industry from “assets” to “people and innovation.” Construction-material suppliers serve many customers. A typical quarrying operation at Graniterock would have more than 1,000 customers, mostly civil engineering contractors. Along with the push toward people and innovation, there is increased emphasis on vertical integration from aggregates to ready-mix concrete and hot mix asphalt, to final construction. If a company is not vertically integrated, it will at least have strong partnerships with other firms, to deliver a high-quality finished project on time.

Jan 1, 2002

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

By D. R. Hack

Increased consumption of concrete in the Pacific Northwest has pushed aggregate resource development pressure from urban areas west of the Cascade Range to rural areas east of the Cascades. Some recent development has focused on barge and rail accessible off-reservation Indian allotments that are exempt from state and county regulations. These lands have their own unique set of challenges, especially when Federal and Tribal governments have conflicting goals and attitudes pertaining to resource development. This paper discusses issues of leasing, reclamation, Federal vs. Tribal authority, cultural resources, and the history of allotment.

Jan 1, 2002

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

Over recent years the trend in Australia has been towards the definitions of sustainable development which emerged from the 1992 Rio Summit of retaining a commitment to ecological integrity, but also incorporating social and economic dimensions of sustainability. Sustainable development may be seen as maintaining and enhancing:natural capital: defined as all natural resources, both environmental and those of traditional economic value; manufactured capital: made by human kind; including produced goods, infrastructure and built environment; human capital: defined as the health, well-being, intellectual capabilities and spiritual welfare of individuals; and social capital: defined as social relations and institutions within and between societies, their norms and functionality (Ameef, 2002). This paper will endeavour to assess the challenges and opportunities facing the professionals and their Institute in the minerals industry in Australia because the MMSD Global and Regional Australia Reports do not, in the authorÆs opinion, adequately address the æhuman capitalÆ input into the current or future development of the minerals industry, in particular, the sustainability of the professionalsÆ skills, knowledge and experiences in a global context.

Jan 1, 2002