Search Documents

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

This paper presents an initial investigation into the viability of co-kriging the grades of multiple mining cuts in a two dimensional, thin reef scenario. Deposits with gradational mineralized zones, in the perpendicular sense, are not as well served by the use of reef accumulation and thickness as deposits characterized by a sharp distinction between ore and waste rock. South African Bushveld Complex platinum deposits and Witwatersrand gold deposits are examples of this distinction. The calculation of an optimal mining cut is of paramount importance in the mining of Bushveld platinum. Two-dimensional kriging of a constant stoping width mining cut is an effective method for resource calculations once a cut is decided, but this begs the question of how to decide on the cut. Comparison of multiple cuts is used as a way of achieving this decision on many of Anglo Platinum’s operations. Although the kriging of each cut is valid in isolation, occasional negative values occur when incremental grades between overlapping cuts are calculated. Negative incremental grades cannot reflect reality. They are thought to be related to the inability of the method to include the strong continuity in the perpendicular direction demonstrated by the relevant variograms. Co-kriging of related variables has been investigated as a potential means tore impose this inherent order relationship. Various co-kriging options have been investigated. The method has been tested on a real data set from an established platinum operation. One of three types of anomaly has been investigated so far. The results show that co-kriging the mining cut grade as the primary variable, with just one secondary variable, the reef thickness, eliminates most occurrences. Severe anomalies remaining are arguably indicative of population mixing and might be more effectively treated by rezoning the data. Aim—To investigate the viability of co-kriging the grades of multiple mining cuts as a method for resolving anomalies in the estimation of such cuts on Bushveld platinum deposits, with applicability to other thin reef type deposits with a gradational not sharp cut-off between ore and waste in the direction perpendicular to the reef. Keywords: co-kriging, cross variograms, ordinary kriging, platinum, two-dimensional, grade profile

Jan 1, 2003

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By Rennie Kaunda, David Streeter, John Kemeny

This paper describes a field/laboratory study that was conducted in cooperation with a mine in Arizona. The primary purpose of the study was to investigate the effect of blasting energy on the crushability and grindability of the post-blast rock fragments. The crushability and grindability of the rock fragments were evaluated through laboratory comminution tests. A secondary purpose of the study was to investigate different laboratory methods for estimating the comminution properties of the rock fragments. In particular, a number of standard rock mechanics tests were conducted and compared with the comminution test results. Finally, the study was used to evaluate new technologies for estimating insitu rock mass strength and for assessing post-blast fragmentation. To estimate in-situ rock mass strength, the specific energy of drilling (SE) was calculated during blast hole drilling utilizing a continuous drill monitoring system. Post-blast fragmentation was estimated using the Split image processing system. Results from the study support the idea that increases in blast energy can enhance crushing and grinding. Also, several simple rock mechanics tests were found to correlate well with the results from standard comminution tests, which could prove to be useful in practice.

Jan 1, 2003

By B. Zlender

ABSTRACT: The paper presents investigation of carboniferous slates from the Trojane hilly area performed on series of samples of equal material. The results of static loading tests show that carboniferous slate is heterogeneous and yields on slate layers. Where that kind of heterogeneity is distinctive the strength results are essentially lower of commonly tests results. The results of dynamical loading tests show that the slate surfaces have the essential meaning for the stability of the material. When those surfaces are moistened the material become unstable. RÉSUMÉ: L'article présente une épreuve des ardoises carbonifères de la région montagneuse de Trojane sur une série des échantillons des matériaux identiques. Les résultats des tests de charge statique montrent que l'ardoise carbonifère est hétérogène et qu'elle cède sur les couches d'ardoise. Quand l'hétérogénéité est distinctive, les résultats de stabilité sont essentiellement plus bas que les résultats obtenus par des tests ordinaires. Les résultats des tests de charge cyclique montrent que les surfaces d'ardoise sont très importantes pour la stabilité du matériel. Quand ces surfaces sont mouillés, le matériel devient instabile. ZUSAMMENFASSUNG: Der Artikel präsentiert die Forschung von Karbonschiefersteinen im Bereich des Bergland Trojane, ausgeführt durch Serien von Proben aus den gleichen Erdmaterial. Die Resultate der statischen Belastungsprüfungen zeigen, das die Karbonschiefersteine heterogen sind und die Schieferflächen nachlassen. Wo bei dieser Art der Heterogenität die Festigkeitsergebnisse wesentlich niedriger sind als bei gewöhnlichen Testergebnissen. Die Ergebnisse der zyklischen Belastungsprüfungen zeigen das die Schieferflächen eine wesentliche Bedeutung für die Stabilität des Erdmaterials haben. Wen diese Schieferflächen befeuchtet sind, wird das Erdmaterial unstabil.

Jan 1, 2003

By Harry R. Asche, Manfred K. Lechner

The Cross City Tunnel comprises 2km of a new underground traffic route in Sydney, Australia. The route is very complex, involving some six separate tunnels and three underground Y-junctions. For almost 200m the six tunnels run parallel at different level sunder William Street, Sydney. Almost all of the route runs adjacent to the City Business District of Sydney and adjacent to or below many major buildings and services. The planning and design of this project is described. The geometric arrangement is achieved with a strong dependence on 3D road design packages. Road alignment constraints include land acquisition and proximity to existing tunnels and basements as well as maintaining separation from the other tunnels in the scheme. Geotechnical and hydrogeological studies are described. Findings discussed include the high horizontal stress field in the Sydney area and investigation of incised palaeochannels on the route. Methods of design for the tunnels and Y-junctions are described, as well as methods of settlement prediction for the buildings and services. The latter includes the settlement assessment for more than 200 buildings, many in excess of 20 storeys, as well as services including all of the city railway lines in Sydney.

Jan 1, 2003

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in 1994 initiated a dynamic shift in the ownership, management and development of the country’s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system, started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress’ Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since 1955 there have been important changes affecting the rules of mineral development. These are: •Firstly, a drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully •Secondly, the globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists; and •Thirdly, the introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its Regulations, the much-publicised Broad-Based Socio-Economic Empowerment Charter and its associated Scorecard.

Jan 1, 2003

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By Karl J. C. Harries

13.1. RIGHT TO RECEIVE ROYALTY CONTRACTUAL ONLY1

Jan 1, 2003

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By J. A. Finch, T. Weber

"Bubble size in flotation is strongly influenced by frother concentration in the pulp liquor. There is no accepted method of judging the dosage and thus how effectively frother is being distributed to control bubble size is not known. This will hamper certain plant test work where constant bubble size (e.g., when comparing reagents) is implicit. Bubble size is not easy to measure in plant and gas holdup is suggested as a surrogate in the development of a proposed “meter” to estimate frother concentration. The meter is calibrated to enable frother concentration to be estimated on samples drawn from any location in the flotation circuit. The meter and its calibration are described.As general background the action of frothers in reducing bubble size by retarding coalescence is discussed and the bubble generation systems for which the effect will be important are considered.INTRODUCTIONBubble size is an important variable in flotation. The flotation rate constant k has been related to mean bubble size Db by k % Db -n with n ranging up to 2 (Ahmed and Jameson, 1989) and even 3 (Yoon, 1993). Recent work has introduced k % Sb, the bubble surface area flux, given by Sb = 6 Jg / Db (where Jg is the superficial gas velocity or volumetric gas rate per unit cell cross-sectional area), i.e., n = 1 (Gorain et al., 1998). Regardless of the exact value of n, the significance of bubble size in flotation remains. In many plant trials it will be implicit that bubble size has not changed and attention will focus on other process variables. The measurement of bubble size, or a surrogate, would be useful addition to any test work.The size of the bubbles is influenced by several variables, gas rate, gas injection system (e.g., impeller design and rotation speed in a mechanical cell) and pulp composition (chemicals added, percent solids), but the most important is frother concentration (Harris, 1976). The frother functions by retarding coalescence (see appendix), which acts to preserve the small bubbles generated in the pulp (and permits a stable froth to form on top of the pulp). The measurement of bubble size is thus related to measuring frother concentration. The distribution of frother and whether sufficient (to control bubble size) is reaching the intended parts of the circuit then become important considerations. At present there is no simple way to judge frother concentration in a plant. In this communication we introduce a possible methodology, a “frother concentration meter”."

Jan 1, 2003

By Ximing Yuan, Yongsheng Xu, Hongjie Li

A study of a static demolition agent that can be used underwater has been carried out. A new type of granulated static demolition agent with rapid reaction has been tested in several hundred experiments. It can be used conveniently and simply in the field. It demonstrates a fast reaction rate with high expansion pressures. The important characteristic of the new type of granulated static demolition agent is the ability to function underwater. It will destroy rock and the other brittle material without flyrock, vibration, shock wave, toxic gas or noise. The reaction rate can be controlled within 30-60 minutes. It is difficult to use these products when the reaction rate is less than 30 minutes and it is less efficient when the reaction rate is longer than 60 minutes. The reaction rate is slightly increased after the material is kept in storage for two years. A new type of the hydraulic device that is used to measure the expansion pressure of solid materials has been designed. The expansion pressure of the granulated static demolition agent has been tested with the device. It is shows that the expansion pressure of the granulated static demolition agent can get to 80~120MPa in 60 minutes. Also included is a discussion of the thermodynamics of the static demolition agent.

Jan 1, 2003

By Ronald L. Bruening

IBC Advanced Technologies, Inc. (IBC) has developed and commercialized SuperLig® materials based on Molecular Recognition Technology (MRT), which have proven to be very effective for the removal of bismuth from hydrometallurgical sulfuric acid process streams. The most common application is its removal from copper refinery electrolytes, where bismuth control is extremely critical. IBC has also developed an MRT system for extraction, recovery and refining of palladium from a copper refinery by-product stream originating from the treatment of copper tankhouse slimes. A high purity palladium salt is produced which meets market specifications. Results are reviewed and discussed.

Jan 1, 2003

By Panagiota Tsolis-Katagas, Basilios Tsikouras, Tassos A. Grammatikopoulos, C. Katagas

"Mineralogical techniques including microscopic methods, reflected and transmitted light microscopy, Cathodoluminescence (CL) and Scanning Electron Microscopy equipped with an Energy Dispersive Spectrometer (SEM-EDS), are useful in determining the quality of industrial minerals. They are essential for studying ores and metallurgical products including the evaluation of physical characteristics of the mineral, paragenetic relationships, associations with possible deleterious contaminants (e.g., sulphides), spatial distribution within the ore zones and liberation characteristics. The methods are inexpensive, and provide quick identification and distinction among the industrial minerals and the gangue minerals in a section. Additionally, SEM is necessary to reveal complex textural sequences and 3-D measurements of minerals and quick semi-quantitative analysis.Common analytical methods include Electron Microprobe Analyses (EMPA) and Whole Rock Analysis (WRA) (commonly with XRF and ICP) for major and trace elements. The EMPA analyses of industrial minerals provide information on the purity of the analyzed grains as opposed to the bulk chemical analyses that may be misleading due to contamination by other associated common “gangue” minerals. These techniques have been implemented for the case studies of wollastonite, V-magnetite and muscovite. Therefore, these methods can provide extremely useful information and lead to the implementation of a successful pilot-testing programme.MINERALOGICAL EVALUATION OF DEPOSITSDespite their considerable and increasing economic importance, industrial mineral deposits have traditionally been neglected by economic geologists, and are only rarely the subject of the detailed analysis widely lavished on metallic mineralization. Moreover, in that they generally represent concentrations of “normal” rock-forming minerals, albeit commonly with particular textural and/or geochemical features, they have tended to fall between the mainstream of petrogenetic studies and mineral deposit research (Grammatikopoulos 1999). For many industrial minerals, little attention has been paid to the factors responsible for their local concentration as large and high-grade bodies. This comparative neglect has particularly been the case for minerals such as talc and wollastonite, widespread in metamorphic rocks, in which they are reasonably interpreted as components of assemblages derived, respectively, from pelitic sediments, ultramafic igneous rocks and siliceous limestones."

Jan 1, 2003

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003