Search Documents

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By Refik Elibay, Lawrence A. Williamson, George D. Barnes

Under an extremely aggressive schedule, final design of 13.5 km (8.4 miles) miles of 8.2 m (27 ft) diameter deep rock tunnel, 322 ML/day (85 million gallons / day)submersible pumping station and associated facilities were accomplished ahead of a federal court mandated consent decree schedule. Challenges overcome by the project team in enabling timely completion of the construction documents will be presented. Discussion includes evolution of final design, consideration of future O&M requirements, and risks identified for construction and operations, together with measures to manage and proactively prepare for such risks.

Jan 1, 2005

Safety remains a critical priority for the Australian mineral resource industry and will receive increased focus in the future. This is particularly evident in underground coal mines where reserves are becoming deeper and more hazardous to extract. The CSIRO, through its Exploration and Mining Division, have recently delivered on two projects aimed at providing step-change capabilities in real-time risk management and hazard control. This paper describes the key outcomes of these projects.

Jan 1, 2005

By Emmanuel N. Zevgolis Ismene-Polyxeni Kostika

Keywords: reduction, kinetics, laterites, rotary kiln, dust In this work, the reduction kinetics of dust from nickeliferous Greek laterites is investigated. The dust is a by-product from laterite treatment in rotary kilns and it comes from washing towers, electrostatic filters and polycyclones. Laboratory made pellets from this dust were also examined. Reducibility was studied in the temperature range of 700°C to 850°C in a laboratory tube furnace. Kinetic analysis of the results showed that at lower temperature values the mixed kinetic model verifies the experimental results of dust and pellet samples. At higher temperatures (800° and 850°C) diffusion becomes the rate controlling mechanism. The calculated activation energy values verify also the above mentioned results.

Jan 1, 2005

By D. Drymonitis, G. Gialoglou

"Placer gold mineralizations have been observed in the north-eastern parts of Greece. Some of them have been at first evaluated to be of special interest so, exploration campaigns have been designed and carried out. Among the other exploration techniques applied on the sites of interest, drilling was the one to give the detailed information and data for the evaluation of the deposits. Having collected the data from trenching and two consecutive drilling campaigns, they were processed geostatistically to estimate the ore reserves and therefore the economic interest of the deposits. The latter was done by using exploitability indices, which would give a rough idea whether the deposits were economically feasible. A small number of such deposits have been spotted in the area and have been explored and evaluated as above. The present paper deals with the most important of them, giving all the process followed and the results derived from the exploration carried out."

Jan 1, 2005

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By J. MacFadyen

The U.S. cement industry experienced its best year ever during 2004 in terms of production and shipments of cement. Clinker, portland and masonry cements production and shipments were up considerably. Clinker production as reported to the U.S. Geological Survey (USGS) was 87.75 Mt (96.73 million st), an increase of 5.4 percent. Gray and white portland cement production from domestic and imported clinker was estimated to be 91.6 Mt (101 million st), up 5 Mt (5.5 million st) from 2003.

Jan 1, 2005

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005

By Chris Bennett, Drupad Desai, Kirit Mevawala

INTRODUCTION The design/build (D/B) philosophy of contract delivery is neither new nor unusual when it comes to at-grade, elevated or high-rise structures. But when it comes to constructing underground facilities, there were no examples to be followed in early 90sin the continental United States or its territories. When DMJM+HARRIS was selected as general architectural and engineering consultant for the Tren Urbano (TU) project in Puerto Rico, one of the requirements of the Federal Transit Administration (FTA) for funding commitment was to use TU as a demonstration project utilizing design/build contract delivery method. Now fifteen years later, New York City Transit (NYCT) has instituted a similar requirement for their first Tunnel Boring Machine (TBM) contract for the Second Avenue Subway. As with most construction mega-projects, lots of things have happened and there were several lessons learned from the TU experience that are now being applied to Second Avenue. Both of these projects require building tunnels and underground transit facilities in heavily traveled corridors of an urban city, in the vicinity of active business and commercial enterprises. To enhance the challenge, there are noise and vibration sensitive and historic urban receptors either over or along both the transit corridors. Column free Tren Urbano station caverns over18 m (60 ft.) wide were built in soft ground conditions within 3.6 m (12 ft.) of the surface under an aging heavy utility corridor, while NYCT tunnels with station structures stretching the limits of rock caverns to 34.8 m (100 ft.), were planned in rocky geology with the presence of shear and fault zones and some mixed face conditions. BACKGROUND During the early period of design/build experimentation, the speed with which the contract procurement packages could be put together enabled the owners to take advantage of the major efforts underway to rebuild the infrastructure that was suffering from post-World War II neglect. Use of design/build for new starts was unheard of and most of the projects were smaller in nature in order to allow the methodology to be tested. Development of functional design packages with the understanding that the D/B

Jan 1, 2005

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By Anthony L. Reynolds, Clifford J. Wren

"The adoption of a significant pile testing regime, the use of Eurocode 7 as the design standard, the development of lean construction techniques, and lateral thinking in overcoming some considerable construction challenges allowed Stent Foundations to construct the foundations for the new Wembley Stadium, London, on time and within budget. In addition to the piling works for the main stadium, and after significant design development, a large number of extra piles were required to raise the new iconic roof Arch to its final position some 133 metres above the ground. A 1,400m long contiguous bored pile wall was also constructed to allow for excavation and formation of the new pitch. INTRODUCTIONHjstorjcal lntrodyctionWembley Stadium is the 'home of English football'. As long ago as the 1880's, Wembley Park leisure grounds had football pitches and running tracks.In 1918 the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Exhibition area covered 219 acres and the area on which a former abandoned tower called Watkins Folly had stood was chosen as the site for the new stadium (http://www.wembleystadium.com).The Empire Stadium, as it was originally known, was designed by architects Sir John Simpson and Maxwell Ayerton and the engineer Sir Owen Williams. It took just 300 days to complete at a cost of £750,000 ($1.4m), and was built using 25,000 tons of ferro concrete, 1,000 tons of steel, and over half a million rivets.The Empire Exhibition was a remarkable event, containing fountains, lakes, gardens, and many pavilions, each representing the architectural style of the countries exhibiting. It was opened on 23rd April 1924 and the final attendance was over 27 million, with 4.5 million admissions to the Empire Stadium alone."

Jan 1, 2005

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By M. Kerr, Petra Lampinen, Jinming Zhang, Petra Brodin, C. Hull, Nils-Johan Bolin, R. Asmatulu

"According to Darcy’s equation, the rate of dewatering varies as inverse square of the surface area of the particles to be dewatered and is proportional to the pressure drop across a filter cake. Thus, the difficulty in dewatering fine mineral concentrates can be overcome by using high-pressure filters. When treating ultrafine particles, however, it is often necessary to further dewater the filter cake using a thermal dryer. In the present work, novel dewatering aids that can reduce the pressure requirement have been developed. The reagents are designed to reduce surface tension, increase particle hydrophobicity and increase capillary radius, all at the same time. They were tested for dewatering mineral and coal concentrates in both laboratory and pilot-scale tests. The results show that the use of the novel dewatering aids can substantially reduce cake moistures and, at the same time, increase throughput. In this communication, the case history of using the reagents commercially at the Garpenberg concentrator is given. The use of the novel dewatering aids allowed the operators to use a vacuum filter to obtain desired cake moistures and obviate the need to use a thermal dryer.INTRODUCTIONDewatering is an integral part of mineral and coal processing operations, as it is necessary to remove water from concentrates (or clean coal) to minimize shipping costs, meet contract specifications, and recycle the process water. In general, the cost of dewatering increases with decreasing particle size, which can be attributed to the difficulty in removing the water trapped in the pores (or capillaries) formed between the particles constituting a filter cake.The various parameters affecting the process of dewatering, including the effect of particle size, can be understood in view of Darcy’s equation (Darcy, 1856):"

Jan 1, 2005

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polypropylene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2005

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By J T. Smit

The theory of froth flotation developed slowly, in almost all cases lagging behind practical developments in the operation of flotation processes. This was largely the result of a lack of understanding of the required basic principles of chemistry and physics, many of which were being developed at the same time. A review of some of the early theories propounded is worthwhile, and should encourage those who are presently studying or practicing flotation to exercise some care in claiming a complete understanding of the underlying phenomena in the art. This paper considers theories presented up to and including those in Principles of Mineral Dressing by Antoine M Gaudin (1939). Of course, developments since that time are important, but they are beyond the scope of this discussion.

Jan 1, 2005

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

By G Bubner, C Gaughan

Magnetite mineralisation within the South Middleback Range has been known since the early 1930s; however, it was not until 1989 that BHP (then owners of the Middleback Ranges mining leases) drilled 10 700 m of diamond core into what was then known as the Iron Duchess low-grade deposit. In 2002 a review of Iron Resources left in the Middleback Ranges and the identification of downstream processing benefits using magnetite as a primary feed source led to the commencement of an 18 000 m resource drilling program of the high-grade core of the Iron Duchess low-grade orebody (renamed the Iron Magnet deposit). This paper describes the geology, processes and procedures used since drilling recommenced in early 2003. The Iron Magnet deposit is located 53 km southwest of Whyalla in the South Middleback Range, South Australia. It is a Paleoproterozoic stratabound magnetite deposit that lies down-dip and lateral to the Iron Duke hematite deposit, hosted within the Lower Middleback Iron Formation of the Hutchison Group meta-sediments within the Cleve subdomain of the Gawler Craton. Magnetite bearing host units within the Lower Middleback Iron Formation can be divided into a æmixedÆ basal sequence, a lower iron carbonate unit, a middle iron talc unit and an upper iron silica unit, all units grading up sequence and laterally into one another. The magnetite mineralisation is hydrothermal in origin. The strongest consistent mineralisation coincides with the iron carbonate unit, and the hematite orebodies of the Iron Duke are interpreted to represent up-dip supergene enrichment of the same unit. The Iron Magnet occurs within a large-scale parasitic syncline-anticline pair on the west limb of a larger syncline. Major bounding north-south shear zones occur on the east and west sides of the deposit. Cross-cutting west-northwest, northwest, northeast and east-northeast trending faults displace mineralisation. The commencement of drilling in 2003 lead to the migration of geological and geochemical databases, re-logging and re-assaying of all old cores that intersected the deposit, updating of logging codes and procedures, and strict Qa/Qc procedures to ensure the study satisfied JORC standards. External consultants were used for auditing and bench marking. The strong geophysical responses of magnetite and the wealth of close spaced ground magnetic and gravity data already completed over the Middleback Ranges allowed for refining of drill hole targets for the drilling program. It also provided an indirect method for ascertaining magnetite grade and tonnage volumes.

Jan 1, 2005