Search Documents

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By E. Krause

The oxidation of Fe(II) with S(IV) and oxygen can be used advantageously in leaching systems requiring both Fe(III) and sulfuric acid; e.g., heap leaching of sulfide-containing ores or concentrates. The oxidation of Fe(II) with SO2/air is several orders of magnitude faster than with air alone; rates of up to ?20 g/L'h were observed at 25°C. The reaction proceeds via an intermediate orange-red mixed-valence Fe(II)/Fe(III) sulfite complex, which is present at an essentially constant concentration throughout most of the oxidation process. The oxidation rate of Fe(II) is approximated by the formula -d[Fe(II)]/dt = k [S(IV)] [02]0'3. The concentration of the mixed-valence complex, and thus the iron oxidation rate, decreases with increasing acidity. Certain impurities, such as SCN- and thiourea, negatively affect the rate. The oxidation reaction 2Fe2 + SO2 + 02 4 2Fe3+ + S042- is accompanied by the side reaction H20 + SO2 + 1/202 4 H2SO4. The side reaction becomes particularly important at low temperatures and whenever the oxygen mass transfer is insufficient with respect to the rate of addition of S(IV). Thus, effective oxygen mass transfer is essential for achieving high oxidation rates with minimal acid formation. The activation energy was estimated as 141 kJ/mol over the temperature range 10-35°C.

Jan 1, 2006

By O. Acaroglu

Selection of the most suitable roadheaders (boom type tunnelling machines) for the galleries/tunnels to be excavated in certain rock and under known project conditions is important for avoiding problems during application. This research utilized a multiple attribute decision-making method and studied how this will be applied for the selection of boom-type excavation machines. The Cayirhan Coal Basin was used for selecting roadheaders using the analytical hierarchy process, which is one of the multiple attribute decision-making methods. To conclude, this study reveals that decision-making methods can be used in the process of selecting roadheaders for the excavation of galleries. Keywords: roadheaders, multiple attribute decision-making, analytical hierarchy process.

Jan 1, 2006

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By Vojteh Leskov?ek

The tribological load is the load on forging tools resulting from the relative motions between the plastically deformed workpiece and the die. In comparison to many other forming processes hot die forging has an especially disadvantageous tribological system. The advantages of the application of hard coatings, which are well known for cutting tools, are to a much lesser extent explored for casting, extrusion, molding and forging tools. Increasing the lifetime of these tools is an important task in surface engineering because of the complex loading conditions and often complicated tool geometry. The plasma-assisted chemical-vapor-deposition (PACVD) technique is well suited to depositing hard coatings onto large dies and molds. The aim of this study is to present and discus results obtained on a duplex PACVD hard coating in an industrial application like the hot forging of automotive parts. A new generation of vacuum-melted and remelted (VMR) hot-work tool steels has been developed; these can reach a hardness of 58 HRc, and have a fracture toughness at this hardness equivalent to that of standard hot-work tool steels at 45 HRc. This offers one of two advantages: the steels can be used at the higher hardness to provide resistance to wear or deformation, or, when used at a hardness of 47?49 HRc for hot forging, to provide temper resistance, nitriding behavior and adhesive wear resistance. The results presented here are from a preliminary investigation. The experimental results indicate that the introduction of a proper duplex PACVD hard coating will lead to an improved wear resistance and a longer lifetime for the hot-forging dies. Furthermore, by using a hard, low-friction coating excellent anti-sticking properties can be obtained. At this stage of the investigation it is also necessary to carry out pilot trials to determine the wear resistance and the tool life in practice.

Jan 1, 2006

By David J. Blackwell

The challenge; to design production facilities and in particular separation equipment which have the ability to deal effectively with the ever changing composition of well fluids, over the life time of the field in which it is operating, ensuring maximum uptime of the asset coupled with consistently effective separation. Design engineers are, however, continually confronted with a dilemma when selecting materials of construction for Oil/Gas separation equipment, since they are generally obliged to select an acceptable material of construction, based on ?predicted? operating conditions, at the lowest acceptable cost. Consequently many designs are somewhat basic and do not take into account the constantly varying dynamics of the well fluids being released into the separator. As oil fields mature, oil companies endeavour to maximize revenue by maintaining oil and gas throughputs. This often results in an associated increase in water and sand volumes and, in order to maintain efficient separation, an increase in operational temperature and pressure; subjecting the equipment to operational conditions for which it was never designed. In reality, therefore, the limitations and constraints placed upon new construction design often result in Maintenance Engineers having to solve the ensuing problems in difficult ?in-field? environments. Should refurbishment or upgrade be required then the status of the platform and that of the vessel during shutdown will dictate how this is achieved. Hotwork on the vessel is generally not preferred due to the requirement for post weld heat treatment and re-classification of the pressure vessel, not to mention the added risk in terms of safety. Unfortunately, until recently, there have been few alternatives to conventional ?hotwork? repair and protection systems, especially since the performance of cold curing polymer based repair and coating systems, for use in oil and gas process equipment, has, until recently, been limited by their resistance to temperature and pressure in immersed conditions. In line with the continued development of high temperature / high pressure oil and gas fields however, recent breakthroughs in polymer technology can now offer both repair and protection solutions which are able to function effectively at temperatures up to 180°C in immersed conditions combined with resistance to the destructive forces of explosive decompression from pressures in excess of 90 bar. This paper will look at recent work that has been undertaken to determine the suitability of modern polymer based repair and protection systems as an alternative to hotwork; thus enabling newly designed and upgraded internals to be cold bonded into position and further protected with temperature resistant coatings, in order to minimize the downtime of the asset and further to protect the vessel internals from the Erosive Corrosive environment.

Jan 1, 2006

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By W. Z. Rogers

U.S. feldspar output sold or used in 2005 was an estimated 760 kt (838,000 st), valued at $44 million free-on-board plant. This was below the 2004 volume and was the second year of decline in a row. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures and fiberglass insulation requiring feldspar. Shipments of glass containers were about the same as in 2004. Imports of ceramic tiles and plumbing fixtures continued to increase, taking the place of U.S.-produced goods and the feldspar required to make them. For 2005, 80 percent of the ceramic tiles sold and 50 percent of the plumbing fixtures sold in the United States were imported. Since 2000, manufacturing plant closures in the plumbing fixtures industry have reduced the demand for feldspar and feldspar-silica mixtures by 100 kt (110,000 st). Increased demand from the ceramic tile industry has partially offset the lost volume.

Jan 1, 2006

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland.   Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz.   Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this.   Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By C. S. Chenga

Sustainable development is currently an extremely relevant concept worldwide, especially in developing countries like South Africa. Mining and metals companies are also directly affected by the sustainable development agenda. The Mining Charter?s requirements as well as new legislation (Mineral and Petroleum Resources Development Act) expect, among others, for mines to support infrastructure and poverty eradication projects in the communities surrounding the mines. The aim of this paper is to, against the background of a qualitative study of mining communities in the North-West Province of South Africa, put forward some critical factors for the sustainability of social development projects in the mining sector.

Jan 1, 2006

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By M. Hochenhofer

Due to economic aspects and environmental regulations recycling of slag and waste from ferroalloy production became a very important issue for the companies during the last years. The treatment of slag depends prior on the composition, especially on their content of valuable metals and impurities. The final aim should be a total re-use of these materials in the industry e.g. cement industry, pig-iron production etc.. Therefore, to reach the required physical and chemical properties for a further use, possibilities of a metallurgical treatment have been investigated. The conditioning of slag with a high V-, Mo- and P-content via reducing metal bath showed to be one alternative. To determine the optimal process parameters, practical investigations with different slag compositions and thermodynamic calculations were carried out.

Jan 1, 2006

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

Early strategic mine planning includes decisions over the organisation of work and workforce accommodation. These decisions involve significant commitments that affect not only employee quality of life but also the impacts and relationships with existing local communities. Strategies for workforce accommodation are characteristically community-based (either as purpose-built company towns or integrated within existing local communities) or commuter (fly-in, fly-out) mine camps. The quality of accommodation underpins the fulfilment, morale and motivation of employees. This is not only relevant to productivity and safety, but also to recruitment and retention, particularly with the current onset of a significant human resources crisis. In the event that communities exist in proximity to a proposed mine then the accommodation strategy selected can influence the value-adding potential for the sustainable development of such communities. This early planning is particularly challenging where mine locations are isolated and/or face significant economic, social and political adversity. This paper draws upon a case study review of five large mining projects implemented in three South American countries, selected to cover a range of scenarios and accommodation strategies. The review aims to advance our understanding of the complexity of the underlying planning issues. Each scenario considered the prevailing environmental, social, economic and political situation, together with the adopted accommodation strategy. The case study review aimed to identify lessons learned and to make recommendations for advancing mineworkersÆ accommodation planning practice.

Jan 1, 2006

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

By Emma Arakelova

An increase in concentration of a Zn-containing volatile complex for synthesis of ZnO films was investigated when processing their target by ultraviolet radiation emitted by mercury lamp. The experiments were carried out using a flow-type quartz reactor. ZnO tableted target was preliminarily irradiated during 2 to 7 hours. H2O2 (98%) vapor at 25Pa passed through the reactor with ZnO target at 373K. As substrate material, five subsequent quartz cylinders were used at 423K. The experiment lasts 4 hours. H2O2 decomposition on ZnO surface was accompanied by formation of a Zn-containing volatile complex which passed in gas phase and decomposed on the substrates with isolation of final ZnO. The concentration of the Zn-containing volatile complex (N) in gas phase increases with UV pre-irradiation time (t) (without irradiation N = 1.05 1011 particles/cm3; after t=2 hours, N = 5.19 1011 particles/cm3, after t=4 hours, N = 9.95 1011 particles/cm3; after t=7 hours, N = 1.86 1012 particles/cm3.

Jan 1, 2006