Search Documents

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By FT Cawood

The latest Draft MPRRB was released for public comment in October 2006. The main purpose of the Bill is to collect royalties at mines developed in terms of new-order mineral rights granted through the MPRDA process. The transition phase stipulated in the MPRDA will be completed by 1 May 2009, on which date mineral royalties will become payable to the state. The royalty rates stated in the MPRRB differ from mineral to mineral and also depend on the degree of refinement. Gold is the subject of this paper, where the royalty rate ranges from 1.5% (for refined gold) to 3% (for unrefined gold) of sales revenue. This royalty is payable regardless of profit, with a maximum 75% relief for loss-making mines. The purpose of this paper is to establish whether or not it would be necessary for gold mines to adjust their mineral reserve statements as a result of this Bill. The methodology is to add the royalty costs stipulated in the MPRRB to the actual quarterly information for the past ten years as reported by the gold-mine members of the COM. The rationale is to investigate the impact this Bill (in its current form) would have had on gold reserves that must be left unmined in the ground because of a higher pay limit. The results of the study point to a significant impact on reserves available for mining with the subsequent shortening of mine lives and retrenchment of workers. Had the MPRRB been effective for the 10 years prior to 1996, it would have resulted in 46 tonnes of gold being sterilised. Stated alternatively, 30 700 workers at COM gold mines alone would have lost their livelihoods.

Jan 1, 2007

By Mauri Kauppi, Pekka Niemelä

World HCFeCr production is 6.0 million tonnes. Correspondingly 1.1-1.6 t slag / t FeCr is produced depending on the raw material basis. Essentially all FeCr is produced in submerged arc furnaces, while the role of competitive technologies like DC is limited. In all furnaces fluxes are used to optimize the slag composition. Vital characteristics are smelting point, electric conductivity and viscosity. The main components of FeCr slag are SiO2, Al2O3 and MgO. Additionally it consists of Cr-, Fe-oxides and CaO. Granulated slag and/or classified slag products are produced depending on the production process. The slag products are mainly marketed in road and civil construction purposes but also in producing refractories. Normally crushed and screened slags are produced simultaneously when recovering alloy. The leachate of slag products is low and performance results are excellent. Slag products successfully replace natural sand and macadam. Generation of waste is essentially reduced. Producing and using slag products are described as BAT-technology and it is an essential environmental aspect. Outokumpu Tornio Works produces 320 000 t FeCr-slag/a. This paper deals with formation of slag in smelting process, its chemical composition, physical and structural characteristics, utilization and product specifications as well as environmental aspects. The slag products are standardized and CE marked. Additionally the role of slag in smelting and alloy recovery is reviewed in this paper.

Jan 1, 2007

The most expensive unit operation in the beneficiation of ores is grinding. The correct design of the grinding circuit is crucial to prevent unnecessary use of energy. Proper design and evaluation of SAG grinding circuits require the specific grinding energy, which is determined experimentally. The most common tests in SAG grinding are the Drop Weight Test, from the Julius Kruttschnitt Mineral Research Center (JKMRC) in Australia, and the SAG Power Index, from MinnovEX Technologies in Canada. The application of these tests to the same ore sample commonly produces different results. The work reported here aims at comparing the application of these two tests in the determination of the specific grinding energy for sulfide copper ores from Sequeirinho and Sossego deposits, Sossego Project, Companhia Vale do Rio Doce - CVRD, in Para state, Brazil.

Jan 1, 2007

By L. Yacher

Most metallurgical plants already have sophisticated control systems as well as a process-historian that manage thousands of real-time and historical variables. There exists a huge potential for operational improvement through the inference of patterns, correlations and cause-effect relationships within these records. The ability to run online and offline advanced multivariate statistical analyses represents a great potential for the mining industry, in various areas such as cathode quality improvement in an SX/EX plant, the analysis of the correlation between the ore characteristics and the mill throughput, the determination of early failure alerts for major equipment, etc. The background theory is described, as well as some practical experiences of operations in Chile and Peru. Cu2007

Jan 1, 2007

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

By Rick Frechette, Bryan Ulrich

Representatives from several mining operations in three western states left their mines behind for a day in February to discuss with their peers the issue of water. The event was Knight Piésold and Co.’s Roundtable 2007, held in Elko, NV. It was third such event put on by the company. The issue this year was site-wide water considerations.

Jan 1, 2007

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

By Craig Bournes, David Chapman, Michael DiPonio

Historically, boulders are a frequent source of problems in soft ground tunneling. During tunnel construction, the need to manually break and remove boulders as obstructions causes delays to the project. Repairs to a tunnel boring machine (TBM) can also be a source of delays. Managing these problems is difficult since normal soil investigation techniques do not accurately predict the presence or frequency of boulders. This has lead to considerable number of claims for extra costs and delays during the construction of soft ground tunneling projects. These issues are exacerbated in pressurized face tunneling systems where there is limited access to the TBM cutterhead for obstruction removal and/or cutterhead maintenance. The project team that built the Big Walnut Augmentation/Rickenbacker Interceptor (BWARI) Project for the City of Columbus successfully managed the design and construction of a 4,267 mm (14 ft) diameter soft ground tunnel with high boulder concentrations in a complex geologic setting. The management of the boulder issue tookplace during several phases of the project.

Jan 1, 2007

The basic make-up of the majority of currently produced bulk explosives has changed little in the last 20 years. These explosives would be described as mature in a life cycle analysis. Therefore these explosive products and the practical rules for their use are well understood and well established. In recent years there has been interest in low density explosives, predominantly due to ammonium nitrate shortages and the associated increase in the cost of explosives. In the use of low density explosives some of the practical rules for the more commonly used bulk explosives do not apply. Therefore a shift in the thinking among users is required. At a number of mines low density explosives have been trialled or are being used, utilising the practical rules that apply to bulk explosive products. This has led to poor blast results in many situations. These poor blast results have often then led to a reduction in the use of low density explosives at the mine. This reduction does not acknowledge the advantages that can be gained from this product in the area of reduced cost of mining. This paper looks at low density explosives and discusses how and why these products work. Included in the paper are some practical ideas and examples of how low density explosives can be effectively used at the mine site.

Jan 1, 2007

Phelps Dodge has recently operated a commercial scale, super fine grinding circuit of copper concentrates for use in a medium-temperature pressure leaching process. Two 355 kW vertical stirred mills were installed in series, targeting a grind of 80% passing 7.5 µm and 98% passing 15 µm as outlined in Phelps Dodge's concentrate leaching patent portfolio. This paper details the operation and results of the test program at Bag dad, as well as some of the operating challenges encountered.

Jan 1, 2007

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By John J. Murray, Michael T. McRae, Michael A. Krulc, Kathy L. Schuler

The San Vicente Pipeline Tunnel Project involves the construction of an 8.5-foot-diameter water pipeline in an 11 mile tunnel in San Diego, California. The tunnel is located in extremely variable geologic conditions of strong granitic and volcanic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. One reach of the tunnel is a 5,200-foot mixed face reach that includes Friars Formation Conglomerate overlying granitic rock. Due to the variable ground conditions in this reach, the use of a TBM was deemed too risky and the contract documents required drill-and-blast and hand mining methods. Although it was not required, the contractor elected to construct this reach using NATM methods. This paper describes the geology of the 5,200-foot mixed-face reach, the design evaluation, and the construction challenges faced on this project.

Jan 1, 2007

By A. More, J. M. Míguez, J. Bullón

In 2000 Ferroatlantica started a project with the aim to develop a new casting machine for silicon and other ferroalloys. Until now, it has been cast more than 25.000 tons of silicon for the chemical and metallurgical market. This system has improved the process yield, productivity and product quality which place?s Ferroatlantica at the top of technology development in this field. After the first presentation of the Ferroatlantica?s casting machine at Infacon X, we would like to show the improvements in the control which have permitted us to increase the lifetime of the copper and to obtain, at the end of the machine, the right product size for the customer avoiding the current necessity of crushing and sizing the lumpy metal. Furthermore, we have improved the system in relation to the obtaining of smaller granulometries at the end of casting machine. Not only is this kind of machine cost competitive for special silicon applications but also for other normal ferroalloys with different specifications of size and thickness.

Jan 1, 2007

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Deniz Adiguzel

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. In bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. The prediction of ground vibration components plays an important role in the minimization of the environmental complaints. This paper presents the results of ground vibration measurements carried out in the quarries located on the different sides of Çatalca district in Turkey. In order to predict peak particle velocity level for this district, ground vibration components were measured for shots during bench blasting at these quarries. In blasting operations; ANFO is commonly used as blasting agent at the quarries. The type of priming and firing differed from quarry to quarry. The parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events by using different type vibration monitors. The absolute distances between shot points and monitor stations were determined by using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. In order to predict, and compare the influence grades to the neighboring buildings, and structures at the Çatalca district, the particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms due to the lack of a national standard in Turkey. Then, the data pairs belonging to these quarries were gathered together to represent the district and were analyzed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance

Jan 1, 2007

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By PC Pistorius, DR Groot

The South African base metals industry has been one mainly focused on the production of metals or metal compounds from primary ores. This is true for metals such as titanium, vanadium, chrome, manganese, cobalt, nickel, copper, zinc and aluminium. The steel making industry has traditionally used a substantial portion of scrap steel, and could thus be considered to be somewhat of an exception. Secondary sources have played much less of a role, possibly due to at least some of the following factors. Scrap material is often of unknown composition, and thus it requires additional chemical analysis, and possibly special treatment. Tonnages are relatively small, and the incorporation of secondary materials is possibly seen to carry undue risk and inadequate benefit. South African consumers are still not very conservation and recycling conscious, which limits the amount of scrap made available. This attitude might also be expected to influence decision makers in these industries. Finally, pressure from environmentally motivated activists locally has not been unduly large. This landscape has been changing, and is continuing to do so. Various municipal authorities such as those of Pretoria, Johannesburg and Cape Town are reporting increasingly limited landspace for waste (Bondolfi, 2007). There are increasing concerns regarding the leaching of hazardous metals such as chromium, mercury and cadmium from landfill waste, especially electronic and electric wastes ? the so-called eWastes. In more developed countries such as the United States of America and Western Europe the problem of eWaste has grown to the extent where legislation has been enacted, such as the Waste Electrical and Electronic Equipment (WEEE) legislation of the EU (European Union Directive 2002/96/EC). The 19th and 20th centuries have seen major technological advances. Relevant to this paper is the availability of centrally generated electrical power, telecommunication, entertainment through recorded and transmitted music and images, the growth and pervasive influence of electronics, and the handling of digital data by computers and microprocessors. These developments have placed ever increasing demands on resources for the manufacture of electrical and electronic equipment, as well as on the generation of electrical power. Most of the resources required are non-renewable: copper, steel, aluminium and other metals, various thermoplastic polymers such as PVC (polyvinyl chloride), polyethylene and ABS ( acrylonitrile-butadiene-styrene), thermosetting polymers such as epoxies, elastomers such as butyl rubber, glasses and ceramics, and composites such as fibre reinforced plastic (fibreglass). The conservation of non-renewable resources inevitably includes recycling. To a certain extent, recycling of materials locally is well established. Thus glass, paper, used oil, car batteries, ferrous scrap such as beverage cans and non-ferrous scrap such as

Jan 1, 2007

By H. Saridikmen, C. S. Kucukkaragoz

In the present study, the measurement of sulphur distribution ratios between the slag and metal phases encountered in the ferromanganese smelting has been carried out at 0.83 atm of partial pressure of CO at 1773 K by using classical gas-slag-metal equilibrium quenching technique as a function of composition. The distribution results were employed in calculating the sulphide capacities of SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.-S metal phase. It is shown that the sulphur transfer from metal to slag phase increases with increasing the basicity of the slag. As expected, the sulphur distribution ratio decreases by increasing the silica content of the slag system. The effect of metal composition on the sulphide capacities of the slag as well as on the sulphur distribution ratios between the slag and metal phases have been discussed. Emprical relationships were developed to express the sulphur distribution ratios and sulphide capacities of the above slag system.

Jan 1, 2007

By J. de Bakker

It hardly needs to be repeated that if coal is to continue as America’s premier source of cheap energy, it is absolutely necessary that the carbon dioxide from its combustion somehow be sequestered. A promising method proposed to accomplish this is the “indirect” carbonation of serpentine in a concentrated magnesium chloride brine. Indirect carbonation could be also applied to precipitate magnesium in lateritic nickel processing: this would not only solve magnesium-control problems in laterite hydrometallurgy, but also reduce its energy requirements and create CO2-sequestration credits. Fifty-five percent of the electricity generated in the United States comes from coal-fired power plants, and American coal reserves can last over 500 years at 1990-level consumption1. Coal is therefore both abundant and cheap: it could (and in fact probably will) continue to be an affordable source of energy, both for producing electricity and as a feedstock for liquid hydrocarbon production by Fischer-Tropsch reactions. As a result, it is important to find a workable method of permanently sequestering CO2.

Jan 1, 2007