Search Documents

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By N. J. Alderman, D. J. Clowes, N. I. Heywood

The effects were studied of the presence of comminuted flint on the rheological characteristics of chalk slurry pumped through a 92-km long pipeline from Kensworth Quarry to Rugby Cement Works in the UK, and their impact on the pipe flow conditions. Flow curves were measured for 63different chalk slurry samples; these were described by the Bingham plastic model. In addition to observing trends in the yield stress parameter and plastic viscosity in the model with variations in both flint concentration and dispersant additive, use was also made of slurry viscosity values at a reference shear rate of 60 s-1for the pipe flow. It was found that chalk slurry viscosity decreases with increasing flint content up to 10% by weight for a given additive concentration, and increases with increasing additive concentration from 0.7 to 1.0%, for a given flint content. The pipeline flow regimes were identified using the critical value of the Bingham Reynolds number for laminar flow breakdown. For Bench 11 (quarry bottom) chalk slurries, it was observed that all sections of the pipeline operate in the turbulent flow regime for the nine different formulations and for the three pipe diameters used along the pipeline. However, this was not always the case for Bench 1(quarry top) slurries. It was therefore recommended that chalk slurries prepared from Bench 1 should not be used because of the strong likelihood that laminar flow conditions will occur owing to the presence of higher clay concentrations within this bench. This, in turn, will lead to an unsafe operation of the pipeline because of the potential for coarse particle settling. Likewise, blending of chalk from Bench 1 with the lower benches such as Bench 11 could be problematic and this requires further experimentation.

Jan 1, 2007

By B. L. Eggers

This study investigates the application of computed order tracking with subsequent rotation domain averaging and statistical analysis, to the drag gearbox of a dragline used in a mining environment. Computed order tracking is a fault detection method developed to deal with the varying speed conditions often found in industry and has been proven effective in laboratory conditions. Its application to real situations, however, requires some adjustment to deal with issues such as inadequate speed data and the fact that the drag gear rotates in two directions. This provides a unique opportunity to observe the performance of the order tracking method in a bi-directional rotating environment, allowing an investigation of the relationships between the results obtained from each operating direction. A monitoring station was set up aboard the dragline and data was captured twice daily for a period spanning approximately one year. The data captured consisted of accelerometer and proximity sensor data. The key on the shaft triggers the proximity sensors, allowing speed and direction to be measured. The measured speed is interpolated by using various speed interpolation techniques. Then the interpolated speed is used to complete the order tracking procedure that resamples the vibration data with reference to the speed. The results indicate that computed order tracking can be successfully employed in real environments. Furthermore it is shown that the rotation direction that opens the gear-tooth crack gives a better indication of incipient failure. It is therefore important not to disregard either direction when monitoring rotating machinery of this kind.

Jan 1, 2007

By F. F. Peng

The raw-coal feeding system and the upward medium current flow in a dense-medium vessel (DMV) are, in addition to the residence time of particles in the separator, important factors for efficient coarse particle separation. The feed material from a raw coal screen and/or pre-wet screen merge with the major volume of circulating medium as push medium, guided by an adjustable submergence baffle plate deep fed into the separator for effective separation. The remaining volume of the circulating medium enters from the purge and drain hoppers at the bottom of the DMV. This generates a gentle upward medium current flow in the separator, which prevents dense medium stratification/settling and merges as part of the push medium. A two-dimensional, two-phase model developed using computational fluid dynamics (CFD) is used to describe the flow pattern and evaluate the function of the dip plate for understanding the mechanisms of particle separation in the separator. The particle movement in the DMV is also tracked to investigate the major operating parameters affecting the separation performance of the DMV. The simulation results of the DMV separation performance are validated by in-plant test data.

Jan 1, 2007

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

The U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to "disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act." In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable. This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 19602; and these 5-year lists of publications and articles: from January 1, 1965, to December 31, 1969\ from January 1, 1970, to December 31,19745, from January 1, 1975, to December 31, 19796, from January 1, 1980, to December 31,19847, and from January 1, 1985, to December 31, 19898?.

Jan 1, 2007

By L. Ou

This paper reports on research on leaching pyrite in a germ-free system. The effects of mineral particle size, pulp potential and various oxidation agents on pyrite leaching were studied. The results indicated that a smaller mineral particle size leads to a higher leaching rate of pyrite. The optimum results were obtained with a mineral particle size of -0.037 mm. The pulp potential reflected the leaching process and an increasing pulp potential improved pyrite leaching. The leaching rate rapidly increased with the addition of oxidation agents such as Fe3+ and H2O2. However, the precipitate generated by ferric ion coated the surface of the pyrite and prevented further leaching.

Jan 1, 2007

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

By Michelle Mouton, Johanna van Deventer, Jussi Vaarno

Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Impeller rotation speeds of 0-220 rpm were tested, and it seemed that speeds of between 80 and 220 rpm gave similar Fe and Mn removal rates. Co and Cu losses were generally below 1% and 5% respectively at pH 3.

Jan 1, 2007

By W. Langer

Of the 50 or so most often utilized industrial minerals, more than two thirds are, or have been, produced in the western states of Arizona, Colorado, Idaho, Kansas, Montana, Nebraska, New Mexico, North Dakota, Oklahoma, South Dakota, Texas, Utah, and Wyoming. Some commodities, such as natural aggregate, currently are produced in all 13 states; others such as beryllium and iodine are produced in only Utah and Oklahoma, respectively. Together, the 13 western states make a significant contribution to the US industrial minerals industry.

Jan 1, 2007

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

The application of modifying factors to the Merensky Reef and UG2 Chromitite Layer has a number of challenging aspects as the deposits are tabular and consist of a number of separate geological entities that are grade bearing. The important aspects of the conversion include mineral holdings, dilution with grade bearing material, mining and geological losses, marginal cut offs and recoveries especially where open pit or weathered material is being considered. It is considered inappropriate to add material for dilution at zero grade as the associated material generally comes with an associated low grade. The Merensky Reef Is typically a pegmatoidal feldspathic pyroxenite with bounding chromitite layers. The Merensky Reef is senso stricto too narrow to be considered as a mineable entity and therefore any reserve must include material at low or marginal grades. This is further complicated as the typical mine cut or approach varies across a mine of project. This variation must be included in the mineral reserve conversion. The UG2 Chromitite Layer is typically lithologically bounded i.e. chromitite hosted. However, this adds interesting aspects particularly where leaders are intersected in the hangingwall. These can contribute to unstable hangingwall. It may be considered appropriate to include these in the mineral reserve. One of the overarching principles is that the reserve can be demonstrates to be feasible i.e. can be mined at a profit. Here aspects of a feasibility including infrastructure (power, water etc) needs to be properly considered. The paper will attempt to describe these and other relevant issues and highlight examples from experience together with proposed solutions.

Jan 1, 2007

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By L. Andrews

Electron microbeam analysis of metallurgical samples covers abroad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion. Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistry can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis complements bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect. This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly.

Jan 1, 2007

The paper discusses the improvements achieved after an external sparger flotation column was installed as a final cleaner at the Northam Platinum Ltd. UG 2 concentrator in South Africa. It further discusses the improvements achieved after the conversion of a conventional flotation column, utilized as cleaner in the Merensky concentrator, to an external sparger flotation column. Finally, the application of the above knowledge in the design and commissioning of an external sparger flotation column as final cleaner in the furnace slag concentrator, is also discussed. 1. FINAL CLEANER AT THE UG 2 CONCENTRATOR The MF2 designed UG 2 concentrator is processing 75 000 tonnes run of mine ore at a head grade of 4.0 g/t 3PGM+Au and a feed Cr2O3 concentration of 28 %. Since commissioning of the plant in 2001, Cr2O3 in final concentrate amounted to approximately 5 % of the total mass. Although final concentrate produced from the UG 2 concentrator is blended with final concentrate obtained from the Merensky concentrator before smelting, blended Cr2O3 values in excess of 1.6% lead to difficulties in the subsequent smelting process. Several options for reducing the amount of Cr2O3 in final concentrate have been evaluated namely:- ? Differing types of depressants at various dosing rates. This test work did not reduce the amount of Cr2O3 reporting to final concentrate by any significant extent. ? Reduction in mass pull to minimize the entrainment of Cr2O3 in the concentrate stream.. This process change had a detrimental effect on PGM recovery. Conclusions were drawn that conventional mechanically agitated flotation cells could not achieve the required selectivity without sacrificing PGM recovery. As a consequence an alternative mechanism needed to be incorporated for the final cleaning of PGM concentrate.

Jan 1, 2007

By D Vidyarthi

Blasting is the most important activity in the mining industry, the world over. It is a well known fact that only part of the explosive energy gets utilized in causing the actual rock fragmentation. The rest of it gets converted into blast-induced ground vibrations and noise. Though blast vibrations cannot be totally eliminated, it is possible to minimize them by optimization of blast parameters. This paper highlights various in-house efforts put forth by the author towards site specific blast optimization and the monitoring of blast vibrations. It also deals with the prediction curves developed by regular regression analysis for the prediction of ‘blast vibrations’, ‘peak particle velocity’, ‘safe charge’ for various blasts.

Jan 1, 2007

By M Bilodeau, G Caro, R Beaudoin, D Labrie

In 2005, Dyno Nobel Canada Inc, DynoConsult and CANMET-MMSL used their pool of expertise in blasting, ground control, open pit and underground mining, mineral processing, information technology and applied mineralogy to launch a research project aimed at evaluating the role of electronic detonators in the development of a sustainable energy-efficient rock reduction process. The overall objectives were to improve health and safety in a mining environment and reduce energy consumption and greenhouse gas (GHG) production in the Canadian mining industry. The study was conducted in a quarry located in Nova Scotia, Canada, with the objective of taking advantage of the higher accuracy and flexibility of electronic detonators towards improving blast efficiency and measuring its impact on productivity in a quarry environment and energy savings. Optimising the blast sequence was the first aspect to be considered before starting to look at designing bigger blasts and achieving productivity improvements, without creating additional environmental concerns, as the quarryÆs location was representing a challenge in itself in the surrounding community. The use of high-speed cameras (500 fps) was an improved means of analysing blast dynamics during the firing sequence. Seismic monitoring and linear superposition techniques were also applied to validate the sequences to be tested in all three specific geological areas. The combination of field measurements allowed to identify the optimal blasting sequences that would then be delivered accurately with the electronic initiation systems. The data from 12 blasts (six with electronic detonators and six with pyrotechnic detonators) carried out in three different geological formations (soft, medium and hard rock) showed that the electronic blasting technology could increase rock fragmentation by 15 to 20 per cent. A more uniform distribution of rock fragment size was also obtained. Blast improvements on downstream processes resulted in a five per cent productivity increase in rock excavation and transportation, a ten per cent energy reduction in primary crushing and a 15 per cent increase in the primary crusher throughput. A prototype soft-sensor based on primary crusher data (eg energy consumption, throughput, feed and product size distribution) and a simplified computer process model were developed for online measurement of a rock operating work index. Furthermore, rock samples were collected and specimens were prepared in order to determine the tensile and compressive strength of the rock materials, evaluate the aggregate crushing work index and examine the development of micro and macro-fractures under binocular and scanning electron microscopy (SEM). Blast-induced rock damage was evaluated at the end of the laboratory testing program. A reduction in rock hardness by about 30 per cent was observed after blasting. However, the impact of the blasting method (eg using electronic versus pyrotechnic detonators) on the induced rock damage was either absent or not perceptible within the measurement technique accuracy and the number of samples analysed.

Jan 1, 2007

By Vinay Kumar Agrawal, Rama Nath Praharaj

IMFA Group is the largest producer of Charge chrome not only in India but also in Asia. This Group has plants situated at Therubali and at Choudwar. They also have a Thermal power plant at Choudwar which not only caters to the power requirement of Choudwar plant but also supplies power to Therubali. The plants are fed for Chromite ore through the captive mines namely Nuasahi Chromite mines (40.47 Ha) , Bangur Chromite mines(37.34Ha), Sukinda chromite mines (116.76 Ha), Mahagiri Chromite Mine(73.777 Ha) and Chingudipal Chromite mines (26.62 Ha). Nuasahi Chromite Mine, which is situated in Keonjhar district, is an underground mine and is based upon best technological advancements in the industry. The underground mining operation is certified under ISO-9002, ISO-14001and OHSAS 18001. This not only shows the concern for the quality, environment but also for the health of the employees. The Nuashahi is the first chromite mine to backfill the opencast excavations created during the last 50 years and carry out the production from underground area below the opencast workings. This paper deals with the state of art technology of sub-level open stopping in thin ore bodies. The under-ground mine openings was started in the year 1997. In next four years the production of chromite from underground was started.(2001). At present the mine is in a good shape with several running stopes. Today it is producing around 10,000 Mt per month of chromite. The development of the mine is carried out with an average of 200 mtr per month of tunneling. The mine is having a mechanical ventilator having a capacity of24000 M3 per hour at 50mm water gauge, thus feeding sufficient air for the persons working in underground. The mine is being dewatered through a most modern positive suction sump, having a capacity of 500 cum and operated with 120 HP pumps. After commissioning of this sump in the year 2003, the mine has taken a quantum jump in production with remarkable saving in power consumption.

Jan 1, 2007

By G. Watson, S. Sawyer

A Method to Calculate Hydrodynamic Loads on Underground Bulkheads Bulkheads are structures built in openings in underground mines to impound water, preventing the water from entering the active mine workings. These structures not only have to be designed to withstand the static, hydraulic pressure, but also the dynamic or seismic pressure, which would be generated by an earthquake. Bulkheads can be considered underground dams. Unlike dams on the surface, bulkheads are often subjected to hydraulic heads that exceed the heights of the bulkheads. Theodor von Karman in 1933, and Westergaard earlier, developed the equation by which the hydrodynamic pressures on surface dams could be calculated. Civil engineering handbooks of today contain this equation. In this paper, using the methodology developed by von Karman and Westergaard, the authors have developed an equation by which the hydrodynamic forces on bulkheads could be calculated when the hydraulic head exceeds the height of the bulkhead.

Jan 1, 2007