Search Documents

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale.Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and refl ective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become fi lled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

Western Fuels Association, Inc. ?WFA was formed in 1976 ?Nation?s first fuel supply cooperative ?Original members included Basin Electric and Tri-State G & T ?Formed to ensure provision of coal supply to new power plant projects being constructed

Jan 1, 2007

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

The simple act of taking a sample implies that someone will use the information contained in the analytical result to make a decision about a course of action. In the mining industry, the decisions may involve huge capital commitments for opening or closing a mine, or marginal tactical costs that involve deciding if a truckload of mineralized rock should be sent to the mill for processing, or the waste dump. Sampling is among the most fundamental activities in a mining operation, and this paper aims to examine some of the technical issues that can assist in ensuring that samples are representative and correct. Insights into the scale of variability require that we disaggregate sampling variance into its component parts and evaluate each one individually. The work of Pierre Gy in understanding the different sampling errors is the first step in establishing an optimal protocol. This must be followed by the appropriate measures to ensure the protocol is implemented such that minimal bias is introduced in the sampling process. Even with these insights the possibility exists for large unseen and hidden costs can accumulate in a mineral development because of sampling errors. These hidden costs arise due to misunderstanding of the principle factors that affect the size of sampling errors, such as the mass of the sample, the effects of splitting a sample to reduce the mass, and the influence of the nominal particle size. The handling of sample material without due regard to the sampling characteristics of the material being sampled is also a major source of sampling errors. The most significant problem is due to the influence of the so-called volume-variance effect. This effect is a consequence of the support effect and the information effect both of which relate to the difference in size at which samples are collected and mining blocks are extracted. The information effect is a function of the availability of data at the time that decisions are made about the destinations of mineralized rock, namely the mill or the waste dump. Implementation of appropriate sampling protocols in the mineral value chain remains a challenge throughout the industry. The growing understanding and deepening appreciation of sampling theory and methods means we stand on the threshold of a new era for implementing and understanding appropriate sampling procedures and protocols. In the interests of optimal development of the national patrimony it is suggested that standardization through the identification of structural problems and continuous improvement of mining processes be instituted at a national level.

Jan 1, 2007

By A. E. M. Warner, I. E. Hills, C. L. Harris

Since the late Dr. Keith Brimacombe, et al, performed tests at the now-closed Asarco Tacoma smelter and the Inco Copper Cliff Smelter on Peirce-Smith copper converters almost thirty years ago, many Pyro-metallurgists have investigated using the technology. To the best of the authors knowledge, except for shrouded tuyere technologies using substantial oxygen enrichments, the core idea of using high pressure air injection has not been implemented anywhere in the world. This paper reviews the fundamentals of this technology and summarizes the basic economic considerations. It also presents the circumstances of where and when high-pressure injection might be justified.

Jan 1, 2007

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By S. L. Zekovic

This paper analysis the medium and long-term perspectives, framework and considered possibilities of sustainable development of RTB "Bor" (Copper mines in East Serbia) after consolidation in the period of transition. The copper mine was opened in 1903. and today is the best quality copper producer on Balcan. This paper are elaborates the problems of privatization, debt, investment, growth of copper production from own mines (and imported raw), opening of new mines, economical efficiency of production, markets, environmental problems and impacts of the recent industry consolidation. The RTB "Bor" is a serious hot spot in Serbia. Unsustainable trends and processes are identified, as follows: open-pit waste dumps, flotation tailings, mining and processing waste waters, air pollution; no efficiency (excessive) using nonrenewal resource in the copper production; inefficiency in the use of energy, water and other inputs in copper complex; transboundary character of emissions of dust; environmental degradation and quality of wide area and ecologically highly risk, etc. Analysing some trends and planning-developmental perspectives and development strategies of company, it might be assumed that in the forth coming period, in parts of the Serbia, the borders areas of Bulgaria and Romania, there is an anticipated increase of ecological risk.

Jan 1, 2007

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007

By M. Marchese

It is no secret that scarcity of fresh water is an issue that at a global level in the years to come will have a major impact on the business landscape. A number of projects, beyond the mining sector, could remain on paper only due to this. At the same time, this situation is seeing the rise of new business opportunities, such as development of technologies for more efficient usage of water, water recycling, and desalinization of sea water. Despite that most of Chilean mining facilities are located in the driest area of the world, business has developed strongly and actively for more than a century. However, the negative effect on the water reservoirs and the environment is, lately, resulting in the reduction of the authorized water rights. Holding Water Rights for any given volume does not guarantee that the resource will be available when needed. A recent report from the United Nations on global climate change indicates that global warming can be directly related to changes in the natural and human environment. Chile would not be an exception. The reduction in snow levels in the high Andes and reduced rainfall during the so called "Bolivian winter", have directly affected the replenishing of the underground water reservoirs in the lower parts of the valleys, where most of the extraction of the resource takes place. Mining facilities shall be designed to reduce potential environmental effects, using proven technologies, and considering the best practices available. These measures shall constitute a complete structural framework for the environmental impact assessment (EIA) of the Project. The measures to prevent and mitigate the impacts on the water resources shall be considered during the design stage of a mining project. Current and future mining projects in Chile are conscious that the increasing pressure on the limited water resources is becoming unsustainable, and are already facing the water scarcity and social pressure by implementing sea water desalination plants, including long pressurized pipelines to the mine sites (e.g. Escondida, Candelaria, El Morro, Regalito). This paper presents, in summary, an analysis of the present and potential future scenarios.

Jan 1, 2007

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Kagan Ozdemir

In the condition that drilling and blasting technique is inevitable depending on the rock mass and material characteristics on mining activities, the fragmentation rate and particle size distribution of the muckpile after blasting has important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc. and the total costs of that mine. Drilling and blasting is an important step in this process chain and it's results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. There is an increasing body of blasting research indicating significant impacts in these downstream processes.

Jan 1, 2007

By H. Salamanca

Recently, the mining industry has become one of the leading target markets for the technology industry as they need to innovate in their productive processes in order to boost productivity, reduce operation costs, increase operation safety, and improve the quality of life of their workers. This work presents the technological developments that HighService has done in different stages of the mining productive processes to include robotic manipulators in their automation solutions as well as the development of new equipment and sensors. The robotic technology integration is presented in different applications such as handling and selection of cathodes in E-W machines, automation of base plate maintenance, automation of cathode stripping machine, and multi-tools handler for liner bolt replacement in SAG mill liner maintenance activities. The proposed solutions show technical and economical viability with low initial investment and short implementation period of six (6) to ten (10) months. The results have been validated in plant, obtaining higher production rates and availability.

Jan 1, 2007