Search Documents

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By G. Kordosky

The experience of one plant regarding degradation of copper solvent extraction reagents in the presence of 20 to 30 g/1 nitrate in the leach solution was described at Cobre 2003. However, little information is available about the degradation of copper solvent extraction reagents where the nitrate concentration of leach solution is much lower. Analysis of plant organic samples taken from an operating copper SX plant over a long period of time shows that small amounts of nitrate in the leach liquor can be a significant contributor to reagent degradation provided certain other conditions are present. These conditions are discussed and cautionary suggestions on copper SX plant operations in the presence of even low levels of nitrate in the pregnant leach are made based on industry experience with copper solvent extraction plants and copper solvent extraction reagents.

Jan 1, 2007

By Geoffrey Berry

Exposure?response relationships between the relative risk of lung cancer and quantitative measures of exposure to asbestos are available from a number of epidemiological studies. Meta-analyses of these relationships have been published by Lash et al. (1997) [Lash, T.L., Crouch, E.A.C., Green, L.C., 1997. A meta-analysis of the relation between cumulative exposure to asbestos and relative risk of lung cancer. Occup. Environ. Med. 54, 254?263] and Hodgson and Darnton (2000) [Hodgson, J.T., Darnton, A., 2000. The quantitative risks of mesothelioma and lung cancer in relation to asbestos exposure. Ann. Occup. Hyg. 44, 565?601]. In this paper, the risks derived in these meta-analyses have been compared. Lash et al., concentrated on process and found that the risk of lung cancer increased as the asbestos is refined by processing. Hodgson and Darnton concentrated on fibre type and found that the risk was highest for exposure to amphibole asbestos (crocidolite and amosite), lowest for chrysotile and intermediate for mixed exposure. Some of the differences between the conclusions from the two meta-analyses are a consequence of the choice of studies included. The range of asbestos types included in the studies in the analysis of Hodgson and Darnton was wider than that in Lash et al., enabling differences between fibre types to be analyzed more readily. There are situations where occupational exposure to chrysotile asbestos has shown no detectable increase in risk of lung cancer. Taconite miners have shown no increased risk of mortality due to lung cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Amosite; Grunerite; Taconite; Crocidolite; Tremolite; Anthophyllite; Winchite; Risk assessment; Etiology

Jan 1, 2007

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007

By A. Warczok

Smelting slags contain payable metals in a dissolved form and as mechanically entrained matte or metallic inclusions in the size range from 2 to 1000 µm. Slag cleaning requires reduction of magnetite and metal oxides and sedimentation of inclusions. Slag cleaning in an electric furnace is carried out in batch or semi-continuous mode. The strong trend for continuous slag cleaning generates the basic question about the optimal geometry of the electric furnace. Results of combined CFD, potential distribution and heat transfer modeling allowed for the determination of the fluid flow pattern and the temperature distribution in a classical, circular electric furnace as well as in a rectangular furnace. For the rectangular furnace, various length/width ratios and position of electrodes have been simulated. Analysis of key phenomena pointed out the advantages of the rectangular electric furnace over the circular furnace, particularly for continuous slag cleaning. Phenomena that have been analyzed were mass transfer, the rate of slag reduction, coalescence and settling of inclusions, all on the basis of the calculated slag flow pattern and the temperature distribution.

Jan 1, 2007

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

By I. Mazalov, G. Ospanova

Introduction Today, uranium is of great interest because of its application to nuclear power and nuclear weapons. Kazakhstan has been an important source of uranium for more than fifty years. All uranium products are exported. Results In Kazakhstan uranium exploration started in 1948 and developed in several parts of the country thru mining of hard rock deposits. There are known around 50 uranium deposits in six provinces: Shu-Sarysuyskaya (57%), North Kazakhstan (18%), Syrdaryinskaya (15%), Ilyiskaya (7%), Caspian (2%), Balkhash (1%). In the Northern Kazakhstan province, KazSabton took over Tselinny Mining & Chemical Co in 1999. In this province the stockwork is of Paleozoic and Paleozoic folded complexes origin. In the Balkash province some mining of volcanogenic deposits occurred during the Soviet era. This province’s stockwork is of Endogenous origin.In the Ili province uraniumis mainly found in uranium-coal deposits formed by oxidation of the lignite beds roofs. In the Caspian province the Prikaspisky Combine operated since the 1960s a major mining and processing complex on the Mangyshalk Peninsula. This led to the founding of Aktau. It was privatised as Kaskor in 1992 and operations ceased in 1994. The uranium occurrence is associated with the phosphorous from fossil fish bone detritus conglomeration. In the Chu-Sarysu province, which has more than half the country's known resources, both Stepnoye and Tsentralnoye have been operating since 1978 and 1982 respectively. Uranium mineralization occurred in the regional stratum oxidation zones. In the Syrdarya province slightly to the west of the province’s center the No.6 Mining group has been operating since 1985. Uranium mineralization occurred in the regional stratum oxidation zones.

Jan 1, 2007

By P K. Banerjee, S Kumar

Indian iron ores with less than 62 per cent Fe are currently unexploited, except for a few sectors which export them to foreign countries. It is anticipated that by 2012 the countryÆs domestic steel production is likely to rise to the tune of 60 million tonnes per annum. To meet this requirement, it is necessary to utilise not only the existing high-grade deposits but it is also necessary to look into exploiting the leftover iron ores of lower grades. Hence, reserves with Fe content 62 per cent and below (particularly the ores with In the present paper, an attempt has been made to beneficiate three different types of low-grade iron ores selected from three different parts (states) of the country. In the paper, alternative routes for beneficiation and effective utilisation have been tested using different techniques in the laboratory in an attempt to match their (Al2O3/SiO2) ratio after thorough characterisation and liberation studies. The paper also encompasses the geological formations, occurrences and distribution of Indian iron ores as well as highlighting the problems associated with the fines, possible metallurgical routes, and their market segregation from the perspective of end users.

Jan 1, 2007

By W. M. Jansen

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the 'AMIRA P754-Metal Accounting and Reconciliation' project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called `the propagation of error'.

Jan 1, 2007

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By Sverre Olsen, Kai Tang

The composition of ferromanganese slag is very important as it determines the slag/metal equilibrium relations including MnO content of final slag, melting relations and slag viscosity. The slag composition is further expected to influence the process temperature. The properties of ferromanganese slags are suitably described by its basicity and A/S mass ratios. The influence of slag basicity has been discussed in the previous papers. The present paper will discuss the effect of Al2O3 on melting relations, viscosity and MnO-content of final slag. This discussion will be based on assessed thermochemical databases and a recently developed viscosity model.

Jan 1, 2007

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By Wern-ping Chen

To mitigate and control the combined sewer over-flows from 17 outfalls in Detroit, MI, three outfalls in Dearborn Heights, MI and eight outfalls in Redford Township MI, the Detroit Water and Sewerage Department (DWSD) completed the preliminary design of a storage tunnel in 2005. In 2006, a final design revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km (7-mile) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each and 14 drop shafts with various IDs. A small portion of combined sanitary and storm sewers serve the majority of the Rouge Valley water-shed. This includes Detroit, MI and most of the western suburbs. The Northwest Interceptor (NWI), that extends between Eight Mile Road and Ford Road and roughly parallel to the Rouge River, intercepts sanitary sewage and some wet weather flows from trunk sewers in the tributary areas for transport to the wastewater treatment plant (WWTP) for treatment. During extreme storm events, when the capacity of the NWI is exceeded, the excess combined sewer and overflow (CSO) over-flows into the Rouge River through 17 outfalls to local rivers. The purpose of the Upper Rouge Tunnel system (URT) is to capture and significantly reduce the uncontrolled CSO from these 17 outfalls in Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township. When implemented, the

Jan 1, 2007

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By Peter Dowden, Trevor Carter, Allan Moss, Bruce Downing, Richard Beddoes

Traditionally (with a few exceptions) tunnel boring machines (TBMs) have been utilized on tunnel projects where the risks associated with deep tunnels (rock burst, squeeze, etc) are low (or expected to be low). This has generally been due to the extremely adverse consequences of entrapping or damaging a TBM under such conditions; but also due to the relative difficulty of dealing with these ground conditions in the confined working area of a TBM, in comparison to a drill and blast heading. This paper review the constraints of operating a TBM in a deep tunnel and discusses related project experience, particularly recent and current experience with TBMs in the deep Alpine Base Tunnels. Potential future applications of TBMs in the development of large, deep underground mines are also discussed.

Jan 1, 2007

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007

By D. J. Thorkelson

New data indicate Wernecke Breccia-associated iron oxide copper-gold (IOCG) deposits likely formed from moderate-temperature, high-salinity, non-magmatic brines. The breccias formed in an area underlain by a sedimentary sequence that locally contained evaporites (potential source of chloride and possibly sulfur) and was thick enough to produce elevated fluid temperatures. Metals (Fe, Cu, Co, U) were probably derived from host strata, transported as chloride complexes, and precipitated due to changes in fluid temperature and pressure during brecciation. These new data suggest that the spectrum of genetic models for IOCG deposits that typically invoke formation from magmatic or hybrid magmatic-non-magmatic fluids should be expanded to include those systems that formed in a non-magmatic environment. Modifications to the definition of IOCG systems are proposed that reflect the degree of involvement of magmatic and/or non-magmatic fluids and the nature of the mineralizing environment. A division into magmatic, non-magmatic, and hybrid magmatic-non-magmatic IOCG types is suggested. Typical magmatic end-member IOCG deposits include Lightning Creek and Eloise, Australia. Hybrid magmatic-nonmagmatic IOCG examples include Ernest Henry and Olympic Dam, Australia. The Wernecke Breccia and Redbank deposits are suggested as possible representatives of non-magmatic IOCG end members. Endmember magmatic IOCG deposits have similarities to some porphyry deposits, whereas non-magmatic IOCG end members share characteristic with some sediment-hosted Cu deposits, suggesting that the range of IOCG deposits may form a link between intrusive- and sediment-related deposits

Jan 1, 2007

By Luthie Els, Chris Coetzee, Roedolf Koekemoer, Casper Els, Olof Vorster, Frank Fereday

Three electric arc furnaces (EAFs) were constructed by Union Carbide at Tubatse Ferrochrome (TFC) in1975. This plant was expanded to four furnaces at the East Plant in 1985 and the gas cleaning system was enlarged without taking flow dynamics into consideration. In order to improve competitiveness, TFC has increased furnace capacity, partially substituted coal for coke, and changed the charge mix. These changes increase the heat and dust load into the air pollution control (APC) system. TFC embarked on a project to improve the APC capacity by: ?Quantifying the required off-gas capacity ?Optimising the aerodynamic flow through the system by means of Computational Fluid Dynamics (CFD) ?Converting the old Brandt Koyo top entry baghouses to bottom entry ?Upgrading the cleaning system ?Installing Gore-tex® ePTFE membrane filter bags The estimation of required off-gas capacity is traditionally done by rule-of-thumb methods such as specific extraction. A more elegant evaluation method was developed for simulating the effects of changes in charge mix on the furnace reaction gas volume and the APC system. Reaction gases are calculated by modelling the reactions taking place in the furnace and off-gas volumes are compared to both fan and baghouse capacity. This enables identification of bottle-necks in the off-gas system. CFD techniques were utilized to evaluate geometric imbalances and propose solutions to ensure optimal use of off-gas capacity. The system modifications were completed over several months and the modified equipment went into service in May2006.

Jan 1, 2007

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007