Search Documents

By Catherine N. Mulligan

Thickening of mine tailings is a relatively new concept for their sustainable management. Removal of water from the tailings to form a paste instead of slurry disposal decreases environmental and geotechnical concerns. As the use of these pastes is relatively new, their behaviour requires investigations such as liquefaction and seismic stability, freeze-thaw behaviour, consolidation and leachate characterization. Slurry density, ore type, particle size distribution, specific gravity and environmental conditions can all influence paste characteristics. In this paper, the effect of the above-mentioned parameters is examined. New developments in water removal, and additives (such as flocculating agents, cements, organics, fertilizers, etc) leading to low moisture content tailings are reviewed, and the potential for thickening to enable sustainable management of mine tailings is discussed with respect to storage volume requirement, use of virgin land, consolidation of the tailings, land use after decommissioning.

May 1, 2007

By Himanshu Dehra

The pre-fabricated outdoor rooms are often utilised near the mines and construction sites for office purposes. The paper has presented modelling and simulation results of the integration of commercially available glass coated photovoltaic (PV) energy technology and solar ventilation technology into a pre-fabricated outdoor room. The pre-fabricated outdoor room has been setup at Concordia University, Montréal for full scale testing of the glass coated PV modules with solar air ventilation. The computer simulation model has been developed for PV modules installed on a double wall wooden frame in an outdoor room based on its preliminary field testing. The testing apparatus was a wooden frame assembly of double wall with solar air ventilation: two adjacent glass coated PV modules, air column and plywood board filled with polystyrene. The measurement data collected from various sensors were: solar intensity, ambient air temperature, room air temperature, electric power, surface temperatures of PV modules and plywood board, air velocities and air temperatures in the air column. The enhancement in the air velocity of the air column was achieved with an exhaust fan fixed in an outdoor room. The simulation model is used to perform the two dimensional energy analyses with applied one dimensional solution of steady state heat conduction equations. The simulation model is based on conjugate heat exchange paths with network boundary conditions of convection, radiation heat exchange and solar air ventilation heat transport. The model parameters are based on measured values of ambient air temperature, room air temperature, air velocity at outlet of air column in double wall, electric power and available solar intensity. The model has predicted fairly well energy performance of glass coated PV modules with solar air ventilation installed on a wooden frame. The model is also useful for predicting heating, ventilating and air-conditioning (HVAC) requirements for the pre-fabricated outdoor rooms.

May 1, 2007

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

By J. H. Nantel

Indications are that underground mining is gaining favour with large and small mining companies due to environmental and sustainability concerns. Dramatic changes to mine fill technologies will be needed in order to keep pace with these emerging trends. The industry will be compelled to gravitate toward zero discharge mining operations. Innovative handling of mine tailings will become a focal point in this effort. The challenges are to use a greater portion of the residues and to manufacture a fill with better properties. This is a tall order that can only be addressed through a systematic research and implementation process involving mining companies, universities, research organizations, manufacturers and governments. The mining industry has to be at the forefront of this technology push in mine fills for the future mines. It will also be called upon to lead the way in other research areas. The industry will have to partner with other technology providers: universities, government laboratories and consultants.

May 1, 2007

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hard rock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

May 1, 2007

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

By Washington Luiz Mafra

Every year the conventional direct reduction processes ? Midrex and HYL III ? increased their market share in the world steel production, even though they are only economically feasible in countries where natural gas is available at competitive prices. In this context, the new Midrex projects are based on large reactors (Megamod - 1.5 to 1.8 Mt/y of DRI), reduction temperatures of the metallic burden up to 850oC, with bustle gas temperatures between 960oC e 1050oC. Thus, the requirements of metallic burden performance, as well as the evaluating methods, usually based on ISO standards, need to be reviewed. It is well known that the standards usually applied to quality evaluation do not reflect the performance of metallic burden inside the reactors. This paper describes the different methods of evaluating the disintegration under reduction of DR pellets based on ISO 11257 standard. This is the most important method used by pellet producers and customers for evaluating DR feedstocks. The different methodologies tested to evaluate the disintegration under reduction had varying results, evidencing the relevance of the method and the quality of the pellet. Nevertheless, validating the method in an industrial reactor is still fundamental.

May 1, 2007

By Bahram Samani

The Bafq - Saghand ore belt (metallogenic zone) is the main region, where the major discovered Uranium resources are located. This belt is a unique Upper Precambrian terrane experienced Katanga ? Pan African tectono ? thermal events. The oldest sialic crust was formed during the middle Proterozoic and followed by K-granite intrusions of Lufilian Cycle (850-800 M.Y.).This event caused Tectono ? Magmatic ? Activization (T.M.A) characterized by intracontinental rifting and associated ore formations. This zone was considered as an iron ore belt in 1960s ? 1970s, and U ? Th ? REE belt in 1980s ? 1990s, but by new discovered of U ? Mo (Co, Au, As, Cu) mineralization is assigned as a U - Polymetal zone, hosting the full sequences of iron oxide (Cu, Au, U) ore forming groups. On the basis of detailed investigations this zone is characterized by the following peculiarities: This zone is the vestigial vessel of Gondwana basement, where the oldest granite and the first platform clastic cover is exposed. This zone is marginal part of Precambrian continental crust, consolidated in 1.3-1.0 B.a. The sub mature continental crust experienced Lufilian Orogenic and Katanga ? Pan African Tectono ? Thermal event by intercontinental rifting, and ore mineralizations. The ore forming stages were sequential processes, started by enriched mantle derived metallogeny, and ended by interaction of silanes/ HACONS (derived from outer core) with crust. The magnetite- apatite (REE, Ti) metallogeny developed from alkaline- ultrabasic magmatic differentiation, capable to from Au- Ni- Sulfide intrusive massifs during 850- 800 Ma. Degassing of silanes/HACONS from deeper level, not only caused mantle enrichment, and plume upwelling as a frontal load, but also played the main role to develop regional Si (-Na-K-Mg-Ca-Co3) metasomatism, and formation of U- Th- Ti- REE- (apatite, magnetite) deposits. The latest (583-510 Ma old) felsic magmatism was major IGU from U-Mo (-Co-As-Au-?Cu?) hydrothermal vein- type deposits. The albitite- type U- Ti- REE (Th) mineralization could be formed by interaction of ascending, and descending solutions along the deep- rooted structural conduits.

May 1, 2007

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By Robert J. Kuhne

The Iron Ore Company of Canada has successfully employed advanced process control (APC) to optimize the operation of their induration machines. A significant increase in machine throughput and a reduction in fired pellet quality giveaway were observed following the APC implementation on all six machines. This paper discusses the opportunity for process control optimization in induration, reviews the property estimation and multivariable control technologies, and describes how the IOCC control strategy captured this opportunity. APC performance data is presented. The dependence of APC performance on control room operator acceptance, process equipment and instrumentation is highlighted.

May 1, 2007

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By Aleksandar D. Bugarski

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

May 1, 2007

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By Carol Odell

This paper was prepared as a brief for Prospectors and Developers Association of Canada (PDAC) to guide input at a series of round tables carried out by the Federal Government in response to the 38th Standing Committee on Foreign Affairs and International Trade (SCFAIT) report, on ?Mining in Developing Countries and Corporate Social Responsibility?. This document mandate is to provide background information, analysis and recommendations on the practice of Canadian exploration and mining companies abroad. This research was based on 11 case studies of Canadian companies which have experienced conflicts or controversies overseas. All case studies were assembled through an extensive literature review of publicly available documentation and communications with representatives of the mining companies to assist in deepening the insights into the drivers of the conflicts and the needs of Canadian companies in similar situations. The case studies include both exploration and mining operations. Our analysis begins with the identification of general and case specific drivers of conflict/controversy in each case study. Company names are kept confidential and only anonymous results are presented. We make ample use of simple flow charts and schematic diagrams to explain how contextual drivers and aggravators and company drivers and mitigators play varied and interrelated roles in conflicts. The diagrams also illustrate the cumulative analysis of drivers including the linkages among drivers/aggravators/mitigators across different domains (social, governance, NGO/media and company). Finally, we discuss needs of companies and propose recommendations for addressing social responsibility and human rights concerns.

May 1, 2007

By Samuel Frimpong

Synthetic fuel is a liquid hydrocarbon fuel synthesized from unconventional resources, such as tar sands, heavy oil, coal, and oil shale. These unconventional resources are immense and will be a major energy source for the 21st Century as the availability of conventional crude oil and natural gas declines. The authors review the available global distributions, production data, research frontiers, and current research organizations involved in tar sands, heavy oil, coal, and oil shale. Tar sands and heavy oil is mainly deposited in Canada, Venezuela, and the United States. Oil shale reserves are found in United States, Jordan, China and Australia. Coal occurs in United States, Russia, China, Canada, and Australia. Major research and development efforts are focused on reserves identification, transportation technologies, production cost modeling, bitumen extraction process improvements, coal liquefaction technologies, elimination of pollutants, greenhouse gases, and safeguarding human health and the environment. This review forms a major source for educating the public about these important energy sources, and the need to develop environmentally sound technologies and policies for their extraction.

May 1, 2007

By Dina M. Aloi

In today?s evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to ?engage? communities without a clear understanding of ?how? to do this or to what end. This move, away from compliance, develops more of a focus on ?Community? Social Responsibility and sustainability. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of ?engaging? communities in mining project design and development leads to a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be ?engaged? in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this ?engagement? and manage this risk will be discussed.

May 1, 2007