Search Documents

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By Russell Barr

Strategic alignment throughout a mining organization is critical to effective strategic execution and good business performance. The alignment of strategic goals and objectives in the different operations and functions in a large global operation is a challenge facing executive management in light of legacy organizational structure and processes. An additional confounding factor in strategic alignment of acquisition and new project expansion is that mining projects and operations are frequently multi-cultural in terms of country origin as well as organizational culture. This brings together many cultures to accomplish the project or complete an acquisition (Financial Times, 2006). The mining industry presents numerous challenges to executives and mine management by the nature of the operation and organizational processes used in running it. For example, there seems to be an inherent conflict between the individual goals of the components that constitute a mineral processing operation (the mine, the mill, the smelter and the refinery), and lowest cost production of the final product. Managers of these component operations have specific objectives passed down from the corporate executives. Those site managers tend to be compensated based on throughput and perform to this main metric. This tendency to maximize throughput for an individual operation can contradict the general process flow of a best-fit solution to producing the final product at the lowest cost. In an effort to become more aligned, firms are increasingly using balanced scorecard derivatives at great cost and effort (whether internally or externally sourced) in an attempt to help with strategic alignment. Balanced score-cards have been effective in providing a good strategic scorecard to companies with some measure of strategic alignment. Many firms make this effort of using balanced scorecards. However, most firms are not strategically aligned or, at best, are sub-optimized, in terms of strategic alignment (Kaplan and Norton, 2006). The tendency in mining operations is to focus on operating individual components as optimally as possible and stretching existing assets to the best possible production rates. ?Making tons? is the common operational focus. Numerous factors underpin this focus and can affect the ability of the operation?s ability to align properly with the corporate strategy and strategic goals. Critical factors are legacy organizational structure, culture, processes and performance measurement systems. Changing anyone of these factors to affect better strategic alignment requires significant attention to managing change.

Jan 1, 2008

By H. Do

In flotation, hydrophobic particles are selectively collected by air bubbles, and the bubble-particle aggregates enter the froth phase. However, less hydrophobic particles drop off from the froth phase, while more hydrophobic particles are recovered. Thus, the froth phase provides an important cleaning mechanism. In the present communication, the froth-phase recovery process has been modeled by considering particle retention times and the carrying capacities of bubbles. The model predictions are compared with the experimental data reported by Seaman et al. (2006). The results show that the froth-phase recovery varies with particle size, particle hydrophobicity, and bubble coarsening.

Jan 1, 2008

By Anette Mueller, Thomas Schnellert, Sérgio C. Angulo

"The use of automatically sorting technique, to separate gypsum components from recycled material of processed construction and demolition waste (C&DW), is motivated by environmental and economical aspects. Only if the gypsum can be separated the aggregates can fulfill the environmental requirements and also the structural characteristics according to the standards. Furthermore, the separation of red brick can also improve the quality of the aggregates.This paper aims at analyzing the separation of gypsum components and red brick by using the color sorting technique. The impacts on the composition and the envelope density of recycled aggregates are described. Depending on the gypsum content the application of two processing stages (rougher-cleaner) can be necessary to produce aggregates with sufficiently low gypsum content. Additionally, the separation of red brick and concrete is successful. So, the color sorting may be a promising technique to upgrade the quality of mixed C&DW aggregates.IntroductionConstruction and demolition waste (C&DW) is a mixture of different materials. Such mixtures can be used only in low grade applications. If the material is used as certified material for road construction or as aggregate in concrete the concrete particles must be separated from the other building materials. This paper aims at analyzing the separation of gypsum components and red brick by optical sorting. The needed stages of sorting for getting a product quality according to the German Standards are deduced.Gypsum is a building material that is increasingly used for interior works in Germany like it is shown in figure 1 [1]. At present the content of gypsum in C&DW is estimated at about 1 %. Assessments on the basis of material streams of gypsum and concrete and their life spans show that higher gypsum contents of about 3 % must be expected in future [2]. Also in other countries the use of gypsum has grown considerably in the last decades. From the characterization of C&DW available in some cities in Brazil, 4 to 15 % of total amount of C&DW that may arrive at the recycling plant to be processed is excessively contaminated by gypsum. In one of these cities, the average content of gypsum in the C&DW before processing was as high as 2.1 % [3]."

Jan 1, 2008

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the 3D surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. Studying the geometrical and temporal relationship between these two signals opens a broad window through which new management techniques become apparent. In this paper we discuss the signal processing techniques used to study these relationships, as well as the related implications for mining. This research was carried out in association with the Chevron Mining underground molybdenum mine in Questa, New Mexico. Some of these new techniques will be integrated into the decision management process at the mine and will provide insight on ore production, draw control, and safe reclamation. The science of signal processing involves the analysis and interpretation of physical processes that vary with time. Two general categories of signals1 are recognized. A continuous signal is a waveform of varying amplitude that is continuous in time (such as a sine wave). A discrete signal is a sequence of quantized values. The independent time variable and amplitude are sampled periodically such that we only know the value and shape of the waveform at the sampling frequency. Displacements measured by a Global Positioning System (GPS) receiver are an example of this. Discrete signals may be studied in the time, frequency, autocorrelation, or wavelet domains. In this paper the amount of ore extracted from the mine and the measured surface displacements are analyzed in the time domain.

Jan 1, 2008

By Thomas V. Falkie

In bygone days, the mineral engineer spent most of his/her time on the technical aspects of designing, building, and managing mineral operations. In the last few decades, mostly since the 1960s, increasing amounts of engineering man power and time are spent dealing with federal, state, and local government agencies, laws, and regulations. It is not possible to plan, design, build, or operate mines, mills, smelters, or even office buildings without detailed consideration of government regulations and permitting requirements dealing with environment, worker health and safety, etc. The four chapters of this section provide an overview of the social, legal, political, environmental, and health and safety aspects of mineral enterprise. The section sets the stage for the working engineer/geologist in industry, government, consulting, or academe and points the direction for more detailed study in each of these areas.

Jan 1, 2008

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By P F. Knights, P Boniwell

This paper investigates the causes of low effective utilisation of the production drill fleet at the Telfer Underground Gold Mine, as measured by the percussion hours per shift. The first part of this paper focuses on a site time and motion study conducted to accurately identify shift time allocation and optimal drilling parameters (manual versus automatic, and suitable flushing mediums for varying ground conditions) as well as quantifying the business potential for automated or remotely operated production drilling. The second part of the paper focuses on the rate of successful hole completion for automated production drilling during shift changes. Two main areas of drill optimisation were identified. Firstly, a site-specific drilling procedure was established so as to ensure that all operators were drilling using optimal parameters. Total production metres per rig increased by 10.7 per cent as a result of the implementation of this standard. It was observed that a 25 per cent faster overall drill cycle was achieved using air mist flushing, and that manual drilling achieves a 19 per cent faster overall drilling cycle in comparison to automated drilling. Secondly, routine provision to the maintenance department of automation reliability reports that outlined the principal causes of unsuccessful hole completion led to an increase in production metres of a further 4.1 per cent, measured between January 2007 and August 2007. First hole automation reliability increased from 39 per cent to over 77 per cent over the same time period. Second hole automation completion was increased to 74 per cent, leading to a higher proportion of production achieved through automated technologies.

Jan 1, 2008

By Chris Curfman

Sustaining Business in a Rapidly Changing Environment Topics: ?Sustainability @ Caterpillar ?Workforce Management ?Regulatory Environment & the Reality of living in a Carbon Constrained World

Jan 1, 2008

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

By Günther M. Volkmann

Continuous developments in tunneling require knowledge transfer between designers and suppliers to optimize the application of support systems. This collaboration allows the designer access to the latest research results, technical innovations, and support specific measurement techniques as well as the supplier?s experiences on recent projects. Project specific requirements determine the information that can be used to increase support system efficiency, advance rate, degree of safety, or decrease costs. This cooperative effort results in not only an unambiguous tender document, but also an optimized design with reduced risk that is coordinated with safe and high performance construction techniques. This paper will address the benefits of an early collaboration to both the design and the specifications in the tender document by using the A3 Hindhead project (UK) as an example.

Jan 1, 2008

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By I. Ocak

The modulus of elasticity of rock material (Ei) is an important rock property that is used as an input parameter in the design stage of engineering projects such as dam and tunnel constructions, mining excavations, and so forth. However, determination of the modulus of elasticity is sometimes difficult to obtain by laboratory tests because high-quality cores are required. For this reason, empirical methods for predicting the modulus of elasticity of rock material have been popular research topics in recently published literature. In this study, the relationships between the uniaxial compressive strength (UCS), unit weight (?) and modulus of elasticity for different types of rocks were analysed by using 177 data obtained from laboratory tests carried out on cores obtained from drill holes within the area of the Kadiköy-Kartal Metro line (Istanbul, Turkey). Keywords: Kadikoy?Kartal Metro, uniaxial compressive strength, unit weight, estimating the modulus of elasticity.

Jan 1, 2008

By J Elsen, R Snellings, K Van Balen

This research concerns the mineralogical study of the physico-chemical reactions taking place at the pozzolan-binder interface. Lime binder/ pozzolan mixtures have been prepared for different natural zeolites. Analcime, phillipsite, chabazite, erionite, mordenite and clinoptilolite were mixed with portlandite and water, after which the progress in the reaction was quantitatively determined by thermogravimetrical analyses from three to 180 days. A first and important step was the thorough characterisation of the raw materials by quantitative X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope energy- dispersive X-ray (SEM-EDX) measurements of the zeolite minerals, Brunauer-Emmet-Teller (BET) specific surface area measurements, grain-size analyses and cation exchange capacity measurements. Beside these zeolite samples with varying Si/Al ratios, two clinoptilolite samples exchanged to the calcium, potassium and sodium form were studied and the difference in their short- and long-term reactivity was assessed. Also the difference in reactivity between identical clinoptilolite samples ground to different grain sizes, obviously having different specific surface areas, was determined experimentally. The results indicate that the external surface area only influences the short-term reactivity, whereas the cation content has effect on both long- and short-term. Na-exchanged samples combine clearly more portlandite in the first few days, whereas the reaction slows down afterwards compared to K- and Ca-exchanged samples. The early reactivity of the unexchanged zeolite samples could be explained by these two parameters, but their long-term reactivity seemed to be related to their Si/Al ratio. Samples with zeolites rich in Si reacted faster then their Al-rich counterparts.

Jan 1, 2008

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008