Search Documents

By Tony Suckling

The commercially available finite element program Plaxis has a key benefit over other finite element analysis programs in that it has a relatively simple user interface to input and output data. This benefit though may also be it?s weakness in that anyone, regardless of their grounding in geotechnical engineering, may use the program and produce results for design. It is essential, as for all engineering design, that the models are checked by competent engineers. This paper describes the key recurring problems found by the authors when checking Plaxis models, such as the generation of the initial in-situ ground stresses and the modelling of groundwater. Interestingly, the authors have not encountered similar problems when checking finite element models produced using other programs and conclude that this may be due to the higher calibre of modeller needed to use these other programs. The geotechnical industry is in a situation at the moment where senior managers who may not have been trained in finite element modelling are relying on less experienced staff who have had some training in modelling, either at university or post graduation. The quality of this training is variable and all organisations running easy to use programs need to be aware of the potential risks and dangers. Management procedures and engineering checks that are essential to validate the results of these models are described, assuming that those in charge are not experienced modellers themselves. The model checking process by competent persons is absolutely essential and it is hoped that this paper will help those organisations that do not have such procedures as part of their own internal Quality Assurance or design validation system. The procedures described are valid for all finite element programs.

Jan 1, 2010

By Leo Panian

Over the last decade, drilled and post-grouted micropile foundations have come to be increasingly relied upon for resisting seismic loads in building foundations on the West Coast. Micropiles have been successfully deployed in a range of soil conditions, in vertical as well as battered configurations, to support a variety of structural systems difficult soils. Their high load capacity in tension as well as in compression, their ability to be installed in confined spaces with minimal overhead clearance, and their ability to be directly tested in an installation have made them indispensable for seismic strengthening of existing structures. More recently, growing industry experience along with improvements in design guidelines have led to wider acceptance of micropiles among engineers and building officials. The increasing availability of the specialized materials, coupled with growing familiarity with drilling technologies among design-build contractors has made micropiles more cost-effective and competitive. For the first time, micropiles are finding applications in the construction of new buildings, where they are combined with shallow footings in hybrid foundations to efficiently resist seismic loads. These new applications rely on more intensive engineering analyses to evaluate the performance of micropile foundation systems and develop detailed requirements for design and construction. This paper describes the design approaches and the analytical methods for the seismic design of hybrid micropile foundations, and provides examples of recent construction projects that demonstrate the application.

Jan 1, 2010

By H. Yoshida

Jet grouting was first introduced in Japan in the second half of the 1960s, approaching 50 years ago. By the end of the first 40 years, jet grouting from single to triple fluid systems had become a global technology. In the last ten years, progress in the jetting has been remarkable, and operational efficiency has improved. The quantity of carbon dioxide emitted in unit soil improvement has become one-third that of the initial technology. Meanwhile, technologies in waste recycling and horizontal jet grouting are also emerging. This paper discusses developments in the most recent ten years.

Jan 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By M. Reda

Inorganic oxidizing agents of the type MeOx-z such as Chromate, Vanadate, Tungstate, and Molybdate... etc. are widely used as corrosion inhibitor. In non acidic solution these oxidizing agent are reduced on the surface of the meta, according to OX + m e + p H20 Red + n OH" In which y = (n-m)/m. The purpose of this publication is to show that for many metals the value of y for any oxidizing agent determines the possibility of that oxidizing agent being an inhibitor or activator for the corrosion process. The inhibition efficiency for other ions such as Pertecnetate and Tellurate which have not been extensively studied can be predicted. A mathematical, equation was derived to express the relationship among the concentration of oxidizing agent, degree of retardation of the corrosion process I cord cor ° (ratio of corrosion current in the solution containing inhibitor to the base solution) , ionic strength of the solution and the coefficient y. The validity of y and the mathematical, equation were verified by many experimental, works on various metals such as zinc, aluminum and steel. Al, the above research works are based on the published research works of Prof. Mikhailoviskii (from 1979 til, 1998) from the Russian Academy of Science.

Jan 1, 2010

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By Yi Luo

A massive roof fall occurred in a small room-and-pillar coal mine. The roof falls occurred under a barrier pillar in a closed coal mine located a short distance above the active mine. The extensive fractures connected the active mine with the old mine, turning them into a “combined mine.” Since completely sealing off the roof fall area is prohibitively expensive for the mine, ventilating the connected old mine became the only option. A comprehensive investigation was conducted to understand the atmospheric condition in the old mine and to find an efficient way to ventilate the “combined mine.” A set of studies involving geology, gas content, pillar stability and mine subsidence were performed to explore whether the closed mine is filled with an explosive air-methane mixture. The air quantity measurement data were used to determine the resistance of the air path formed through the fractured zone. Observations and measurements made from a tour to the underground and mine surface enabled the formulation of simple but effective ways to ventilate the old mine. The ventilation network analysis also suggested methods of control, so that sufficient ventilation air can be directed to the two parts of the old mine.

Jan 1, 2010

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By R. L. Grayson, S. B. Bealko, L. L. Chasko, D. W. Alexander

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies, including a fire or explosion, a massive roof collapse, mine inundations or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training.

Jan 1, 2010

By K. A. Heasley

The objective of this paper is to back analyze the August 6th, 2007, collapse at the Crandall Canyon Mine in Utah, in order to better understand the geometric and geomechanical factors that contributed to that collapse. In this work, the LaModel boundary-element program, along with the best available information, is used for the back analysis. To initiate the analysis, a six-step base model of the mining in the Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters, rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis, a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) overall, the area was primed for a massive pillar collapse because of the large area of equal-size pillars, 2) the abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse and 3) from the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2010

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By Yi Luo

Longwall coal mines are frequently located in steep mountainous areas with narrow valleys. In order to protect surrounding watersheds and residential structures, support areas are left under the valleys. However, the indirect subsidence effects to the residential structures due to the potential topography effects can be a serious problem. The present study examines a longwall mine in southern West Virginia located in an area with an average slope of about 30°, or 58%, and with an overburden depth that varies from 49 to 376 m (160 to 1,235 ft). A comprehensive investigation was carried out to assess the subsidence and topography effects, as well as other ground control issues at this site. Surface and subsurface movements and deformation were predicted and their direct effects on nearby streams and structures were assessed. The potential and indirect subsidence influences of surface topography effects were assessed. The techniques and results of this investigation are presented in this paper. It shows that the direct and indirect subsidence effects on the streams and residential structures should be insignificant. The post-mining observations agreed well with this study.

Jan 1, 2010

By R. J. Thompson

Well-designed and maintained haul roads are the key to minimizing truck haulage onroad hazards and costs, as well as increasing productivity. In practice, however, designing and managing a haul road for optimal performance is often difficult to achieve, especially when resources assigned to design and construction are constrained. By understanding how a road design is developed from geometric, structural, functional and maintenance considerations and, critically, the interplay between these components in design and operation, optimal performance can be achieved. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for safer and more efficient haulage systems, the truck manufacturers’ requirements for a more predictable and controlled operating environment and the recognition of human factors as a significant contributor to haulage accidents. While the human factor is the most problematic to address in a road design, the paper shows that the more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010